Two pieces of carbon fiber composite are glued together as a lap joint. Shear stress is t= P /A. If the glue has a shear strength of 1.2 ksi and the joint is loaded with a shear load P=1700 lb. , how much glued surface area is required for a good bond?

Two pieces of carbon fiber composite are glued together as a lap joint. Shear stress is t= P /A. If the glue has a shear strength of 1.2 ksi and the joint is loaded with a shear load P=1700 lb. , how much glued surface area is required for a good bond?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.11P: A joint between two glass plates A and B is filled with a flexible epoxy that bonds securely to the...

See similar textbooks

Related questions

Q: SOLID STEEL SHAT 5m LONG IS STRESSED AT 80 MPa WHEN TWISTED THROUGH 4º. USING G = 83 GPa, COMPUTE…

A: Find the diameter of shaft and power transmitted.

Q: Part A The two bars shown in the figure below (Eigure 1) are made of a material that has the…

Q: A bronze bar is fastened between a steel bar and an aluminum bar as shown in Fig. P-211. Axial loads…

A: Given that: For the composite bar maximum allowable horizontal deformation is 3 mm. It is required…

Q: Determine tool life for maximum production

A: Given; Tool changing time is=5.4 min Taylor's tool life exponent=1.3 Acc. to data given we have to…

Q: A prismatic wing box is constructed of two cylindrical tubes (each of thickness welded to top and…

Q: Gas enters the nozzles of an axial flow turbine stage with uniform total pressure at a uniform…

A: This problem is the example of the direct problem. In which the flow angle is specified as some…

Q: 4. Qu object in madio to traued along path absenior eed that ü trauelling hatally at x= 12t° m/;…

Q: Problem 2. A block R of rubber with dimensions a x a xL is confined between the plane parallel walls…

A: For the given loading condition, let us attach a coordinate system as shown below

Q: Air with an initial state at 4.5km is allowed to expand isentropically to a state where pressure is…

A: Given Data: The standard Pull P0 for tape is 5 kg and standard temperature is T0 20°C Area of tape A…

Q: Sketch the stream lines represented by y = xy. Also find out the velocity and its direction at point…

A: Velocity is calculate using velocity component and streamline relations.

Q: Water is flowing at a rate of 228 L/s through a 111 m horizontal pipe having a diameter of 249 mm.…

Q: If the Taylor tool life exponent is 0.1 and the tool changing time is 1.6 min, then the tool life…

Q: Problem 4 - Two homogeneous rods ABCD and BE are bent as shown and rigidly connected to each other…

Q: Q1/ Estimate the hot junction temperature for a cooper wires are used in the micro thermopile show…

Q: The bumper springs of a railway carriage are to be made of square section wire. The ratio of mean…

Q: A man is about to throw a stone by rotating his fully extended arm. If the stone moves at v = 2 due…

Q: A force of 80 Newtons is applied to the handle of the pliers as shown. | 80 N -35 mm 95 mm A 80 N…

Q: An ideal vapor-compression refrigeration cycle that uses refrigerant-134a as its working fluid…

Q: 5-9. By applying a force F, a saline solution is ejected from the 15-mm-diameter syringe through a…

A: Given dataForce F is appliedDiameter of syringe = 15 mm = 0.015 mDiameter of needle = 0.6 mm =…

Q: With respect to the following construction trades, list two occupational injuries commonly observed:…

A: Given Work To find Injuries

Q: 4 Am ob jecet is made p fravel obrerver çees fhat it is fraveluing harizbufally fx= 24t° M/ where…

Q: Hello sir Muttalibi is a step solution in detailing mathematics the s ame as an existing step…

Q: The platform scale consists of a combination of third and first class levers so that the load on one…

Q: Which of the following statement(s) is/are true in minimizing the the stress of a rope. i. Increase…

A: Stress = Force / Cross sectional Area Stress is resistance cause by material against apply load.

Q: If the percent humidity of air (30 °C, total pressure 150 kPa) is 45 % and the saturation pressure…

Q: A flywheel 6 ft. in diameter accelerates from rest at the constant rate of 4 rpm per sec. Compute…

Q: Under steady-state conditions, the wall of a brick house is measured to have an inside temperature…

Q: In the mechanism shown in Figure Q3, the inclined rod AC is pinned to a collar that can slide along…

A: Given: Absolute upward velocity of collar A: →VA=1 m/s Instantaneous angle of rod AC with…

Q: - EXAMPLE 8-1 Laminar Flow in Horizontal and Inclined Pipes Consider the fully developed flow of…

Q: A plant has installed a single suction centrifugal pump with a discharge of 68 m3/hr under 60 m head…

Q: As a thermo-fluid engineer working for an energy startup located at Greentown Labs, you are tasked…

A: Given Inlet temperature of hot gas, Ti = 52oC Inlet temperature of cold water, T1 = 4oC…

Q: What is the atmospheric pressure? kPa Required informetion Ar in a tank at 120 kPa and 300 K…

Q: it velocity is Arodet is travelling in dnother planet where depined by = 412-(ot where t is in…

A: Given Velocity, V = 4t2-6t Time, t = 5 sec Find Displacement, S Acceleration, a

Q: (++612- 15t+7) m where t is in seconds. a. determine when the particle changes direction and it's…

Q: Define two-dimensional stream function and velocity potential. Show that following stream function :…

Q: 1. A jack having square threads of 50 mm nominal diameter and 10 mm pitch is supporting a load of 89…

Q: The impeller of a radial pump with diameter of 34.2 in such that its head is reduced by half. What…

A: Initial diameter of the impeller, D1= 34.2 in Initial head= H1 Given that head is reduced to half.…

Q: solution and explaination needed

A: The Navier-Stokes equation is a partial differential equation that shows the flow of incompressible…

Q: PROBLEM: Given the system shown in Figure 4.21, find J and D to yield 20% overshoot and a settling…

Q: 3. Gear B supplies 20 KW of power, while gears A, C and D withdraw 6 kW, 4 kW and 10 kW,…

Q: At time t = 0, an RC circuit consists of a 15.0-V emf device, a 66.0-n resistor, and a 146.0-pF…

Q: À three-bladed wind turbine has a small, unbalanced mass m =0.3 kg, located at an eccentricity…

A: Given

Q: A 7.6 cm jet of water strikes a vertical plate in its centrod. Find the velocity of water through…

Q: Taylor's tool life exponent is 0.8 Determine tool life for maximum production rate? Tool changing…

A: given : n = 0.8 Tc = 6.9 minutes

Q: Completely solve and provide the diagram. Box the final answers. Use 4 decimals in all instances.…

A: Given DataT1=300KP1=101.325KpaT3=1150Kηm=87%ηc=92%ηT=80%ηgen=96%CV=41860kJ/kgCP=1.005kJ/kg-KR=282…

Q: A small model of a water pump has the ff. performance characteristics: D1 = 9in; N1 = 1760 RPM; Q1…

Q: 2. A tube is made of aluminum ( G = 24 GPa ) and has a rectangular cross section as shown in figure.…

Q: Make a comparison remark about Metrology's line and end standards

A: It is required to determine the difference between the line and end standard.

Q: 4. The tapered shaft is made from E- 36 steel ( G = 80 GPa ), and has a radius which can be…

A: Given Length, L = 4 m Torque, T = 450 Nm G = 80 GPa Find Angle of twist

Q: Determine the magnitude of force F in cable AB in order to produce a moment of 1250 Nm about the…

Question

100%

Two pieces of carbon fiber composite are glued together as a lap joint. Shear stress is t= P/A. If the
glue has a shear strength of 1.2 ksi and the joint is loaded with a shear load P-1700 lb. , how much
glued surface area is required for a good bond?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider the copper lubes joined in the strength of the copper is err = 200 MPa, figure using a "sweated" joint. Use the properties and what is the maximum load P]iwathat can be dimensions given. applied to the joint if the desired factor of safety in shear is FS_ - 2 and in tension is (a) Find the total elongation of segment 2-3-4 (
A joint between iwo concrete slabs A and B is filled, with a flexible epoxy lhal bonds securely lo the concrete (see figure). The height of the joint is h = 4.0 in., its length is L = 40 in., and its thickness is t = 0.5 in. Under the action of shear forces K the slabs displace vertically through the distance d = 0.002 in. relative lo each other. (a) What is the average shear strain in the epoxy? (b) What is the magnitude of the forces V if the shear modulus of elasticity G for the epoxy is 140 ksi?
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
What is the shear stress, fv, for the glue of the lap of the connection with P= 15,000 lb? What is the axial stress due to tension, ft, on the thinner of the two plates?
The anchor opposite is made of Cr-Ni steel. Thereelastic limit is 520 Mpa. What should be the minimum diameter inanchor shear if the load F is 50kN? Consider a safety factor of 2.Please note that the safety factor is applied tothe elastic limit.
The cable of hoist has a cross sectional of 80mm2.The hoist is used to lift a crate weighining 500 kg.The free length of of the cable is 30 m.Assume all deformation is elastic. (a) what is the stress on the cable. (b) How much will the cable extend if it is made from steel(E-200 Gpa)? (c) How much will the cable extend if it is made from polypropylene(E-1.2 Gpa)?
A rope has a cross sectional area of 0.002m2 and is being used to lift a 5000N weight. What is the stress in the rope?
A plastic bar of 88 mm is to be twisted by torques T until the angle of rotation between the ends of the bars is 80. If the allowable shear strain in the plastic is 0.014 radian, what is the minimum permissible length of the bar in mm?
If the contact pressure between the rope and sheave is 2.97 N.=/sq.mm. and used to raise the load of 2T=450 kN. Calculate the sheave diameter if the nominal diameter of the wire rope is 4 cm.
A plastic bar of 53 mm is to be twisted by torques T until the angle of rotation between the ends of the bars is 9 degree. If the allowable shear strain in the plastic is 0.018 radian, what is the minimum permissible length of the bar in mm?