i need the answer quickly Two plates 20 mm thickness arefastened by a number of 25 mmdiameter rivets and an axial load of 500KN was applied, determine the numberof rivets required if the shearing stressof rivets is limited by 80 MPa and thebearing stress of plates is limited by 110?MPa500 KN500 KN150mm25 mm Dia.20 mm500 KN20 mm500 KN

Given Bearing stress = 110 MPa Thickness, t = 20 mm Diameter, d = 25 mm…

Answered: Two plates 20 mm thickness are fastened…

Two plates 20 mm thickness are fastened by a number of 25 mm ameter rivets and an axial load of 500 N was applied, determine the number

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

From the given bracket shown, which consist of two plates riveted to the column by 4-22mm Ø rivets which is subjected to an eccentric load of 150 kN. 1. Which of the following gives the shearing stress due to axial load only? a. 49.325 MPa b. 70.25 MPa c. 80.47 MPa d. 68.25 MPa 2.. Which of the following gives the shearing stress due to moment alone? a. 69.76 MPa b. 70.94 MPa c. 56.39 MPa d. 64.32 MPa 3. Which of the following gives the maximum shearing stress? a. 110.30 MPa b. 120.40 MPa c. 140.50 MPa d. 105.70 MPa
For a lap joint, determine the maximum safe load P which may be applied if the shearing stress in the rivets is limited to 60 MPa, the bearing stress in the plates to 110 MPa, and the average tensile stress in the plate to 140 MPa
A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.375 in., and each side of the pulley support bracket has a thickness of t = 0.3125 in. The average shear stress in the pin cannot exceed 45 ksi, and the bearing stress in the pulley support bracket cannot exceed 65 ksi. Determine the maximum value of Pmax that can be supported by the assembly.
The cylinder of a hydraulic press is made up of thick-walled cylinder having an inside diameter of 300 mm. It is subjected to an internal pressure of 40 MPa Determine the thickness of the cylinder without exceeding a shearing stress of 80 MPa. A. 109.81 mm C. 95.56 mm B. 75 mm D. 120.71 mm
The solid steel rod (1) has an allowable shear stress of 12 ksi. The brass tube (2) has an allowable shear stress of 5 ksi. The diameter of the rod is d1 = 0.625 in. The outside diameter of the tube is D2 = 1.625 in., and its wall thickness is t2 = 0.125 in. The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at B. Determine the largest torque Tmax that can be applied at the upper end of the steel rod.
A 5-mm thick, 100-mm wide AISI 1020 steel rectangular plate has a central elliptical hole 8 mm in length transverse to the applied stress and 2 mm in diameter along the stress. Determine the applied load that causes yielding at the edge of the hole. Ans. 92.43 kN
A 35-mm diameter rivet joins the plates that are each 150 mm wide. The allowable stresses are 200 MPa for bearing in the plate material and 80 MPa for shearing of the rivet. Determine the minimum thickness of each plate. Answer: t = ___________________
A 10-mm diameter steel bolt is surrounded by bronze sleeve. The outer diameter of the bronze sleeve is 20 mm and its inner diameter is 10-mm. Given that the yield stress for the steel is 640 MPa and the yield stress for the bronze is 520 MPa, determine the magnitude of the maximum allowable total load that can be applied to this assembly. (Assume full bond between the steel and the bronze sleeve) Esteel = 200 GPa, Ebronze = 100 GPa, Factor of safety = 1.5
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (sY)st = 640 MPa, and for the bronze (sY)br = 520 MPa,determine the magnitude of the largest elastic load P that can be applied to the assembly. Est = 200 GPa, Ebr = 100 GPa.
A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of a 50 mm diameter solid steel rod. If the compound bar is then subjected to an axial compressive load of 160 kN determine the load carried by the steel rod and the brass bush and the compressive stress set up in each material. For steel, E = 210 GN/m2; for brass, £ = 100 GN/m2
A brass rod 8mm diameter and 400mm long fits centrally inside aluminum tube of the same length having an external diameter of 16mm and a wall thickness of 3mm. The rod and tube are rigidly connected at their ends so that they twist together when a torque of 20 Nm is applied. Galuminum = 30GPa; Gbrass = 40GPa. Determine: a) The values of the torsional stiffness for the rod and the tube b) The torque transmitted by each c) The maximum shear stress in each d) The angle of twist
The d = 17-mm-diameter solid rod passes through a D = 22-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 12 mm. The rod head has a diameter of a = 34 mm, and the head has a thickness of t = 9 mm. The shear stress in the rod head cannot exceed 125 MPa, the punching shear stress in the support plate cannot exceed 80 MPa, and the bearing stress between the rod head and the support plate cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported by the structure.