Two shafts, having axes in the same plate intersecting at an angle of 40°, turn in the same senses at 30 rpm and 100 rpm. Draw a pair of cone to be located on these shafts and turn in pure rolling contact. Diameter of base of smaller cone is 1 in. Calculate the cone angles. CONE ANGLE 1 (driver): CONE ANGLE 2 (driven):

Two shafts, having axes in the same plate intersecting at an angle of 40°, turn in the same senses at 30 rpm and 100 rpm. Draw a pair of cone to be located on these shafts and turn in pure rolling contact. Diameter of base of smaller cone is 1 in. Calculate the cone angles. CONE ANGLE 1 (driver): CONE ANGLE 2 (driven):

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If two parallel shafts are connected by cylinders in pure rolling contact and turning in the same direction, and having a speed ratio of 2.75, what is the Center distance of the two shafts assuming that the diameter of the smaller cylinder is 22 cm? Unit in cm.
Two parallel shafts, 61 cm apart and having a speed ratio of 3, are connected by cylinders in pure rolling contact. Determine the D1 in cm when they turn in opposite directions
Please solve this, thank you very muchProblem: Two parallel shafts, 27 inches apart and having a speed ratio of 2.6 are connected by cylinders in pure rolling contact. Find: 1. diameter of larger cylinder when they turn in the opposite direction 2. diameter of smaller cylinder when they turn in the opposite direction 3. diameter of the larger cylinder when they turn in the SAME direction
Board Exam April 1997. Two parallel shafts connected by pure rolling turn in the same direction having a speed ratio of 2.75. What is the distance of the two shafts if the smaller cylinder is 22 cm in diameter?
Correct Solution need.. Two parallel shafts, 61 cm apart and having a speed ratio of 3, are connected by cylinders in pure rolling contact. Determine the D1 in cm, when they turn in same directions.
Two parallel shafts, 11 inches apart and rotating at 75 RPM and 200 RPM, are connected by cylinders in pure rolling contact. Determine the diameters of the cylinders: (1) when they turn in opposite directions; and (2) when they turn in the same direction.
m) The method of sheet forming in which springback is prevented is called ..........n) With the help of liquid pressure of tubular parts with complex surface geometryThe method used in shaping is called ..............o) The rounding of the two ends of the sheet metal produced in rolling ...........is the error that occurs.
A strip with a width of 12 in. And 1 in. Thick is fed through a rolling mill with rolls of 10 in. Radius each. The work material thickness is reduced to 0.875 in in one step, at a speed of 50 rev / min. The work material has a creep curve defined by K = 40,000psi and n = 0.15, the coefficient of friction between the rollers and the work is assumed to be 0.12. Determine if the friction is sufficient to perform the rolling operation. If so, calculate the rolling force, torque, and horsepower.
mention the advantages and disadvantages of rolling contact bearing
A strip (300x30 mm) is fed through a rolling mill with two powered rolls (each with radius of 300 mm) rotating at the speed of 60 rpm. The flow stress of work material is 90 MPa, and the coefficient of friction between rolls and work is 0.12. For a single rolling operation performed at the contact angle of 6.28°, calculate the followings:a) Work thickness after rolling (in mm)
Show your illustration and complete solution in a drawing plate. Two parallel shafts, 11 inches apart and rotating at 75 RPM and 200 RPM, are connected by cylinders in pure rolling contact. Determine the diameters of the cylinders: (1) when they turn in opposite directions; and (2) when they turn in the same direction.
1. The friction in direct extrusion is ________ Indirect extrusion. a) Greater than. b) Equal to. c) Less than.2. The Temperature in hot forming process is ____. a) (0 to 0.4) Tm. b) (0.5 to 0.75) Tm. c) 0.9 Tm. d) 0.4 Tm. e) 0.8 Tm. f) (0.3 to 0.5) Tm. Where Tm is the melting temperature of the work piece.3. Maximum draft in rolling depends on _______. a) Coefficient of friction and roll radius. b) Thickness of plate. c) Smoothness of roll Surface. d) Roll rotational speed.e) Width of the plate. f) Length of the plate.4. In deep drawing process, the drawing ratio (DR) has a higher limit (value) of:- a) 6. b) 1. c) 4. d) 5. e) 7. f) 2. g) Zero.5. Spring Back is a phenomena usually associated with which of the following processes:-a) Extrusion. b) Forging. c) Bending. d) Wire drawing. e) Rolling. f) Sheet metal cutting. g) Deep Drawing.