Two shafts, having axes in the same plate intersecting at an angle of 45°, turn in opposite senses at 30 rpm and 90 rpm. Draw a pair of cone to be located on these shafts and turn in pure rolling contact. Diameter of base of smaller cone is 1 in. Calculate the cone angles.

Two shafts, having axes in the same plate intersecting at an angle of 45°, turn in opposite senses at 30 rpm and 90 rpm. Draw a pair of cone to be located on these shafts and turn in pure rolling contact. Diameter of base of smaller cone is 1 in. Calculate the cone angles.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: What is the Pure Rolling Bodies in The Mechanical Systems and what its application?

A: Pure rolling refers to the rolling process in which no slide occurs. Pure rolling is a mix of…

Q: Q5- A single-pass rolling operation reduces a 15mm-thick plate to 12mm. The roll has a radius of…

A: GIVEN DATA INTIAL THICKNESS hi=15mm FINAL THICKNESS hf=12mm ROLL RADIUS R=400mm WE HAVE TO CALCULATE…

Q: coefficient of friction between the roll and the plate i

A: Given; In a rolling operation using rolls of;Diameter,D=400 mmThickness, t=35mmFor the given…

Q: Question 8 8.1 Calculate the power required to roll an 8650 steel strip, 140 mm wide and 20 mm thick…

Q: A 150-mm-long, 10-mm-diameter, high-strength cast iron rod is being reduced in diameter to 8 mm by…

Q: city 8f steadily decrease from entrance to exit. ii. Rolling is most effective in the absence of

A: The velocity of the sheet increases from the entry of the roll to the exit of the roll. It helps in…

Q: If two parallel shafts are connected by cylinders in pure rolling contact and turning in the same…

Q: Two parallel shafts, 20 in. apart and rotating at 450 rpm and 112.5 rpm, are connected by cylinders…

Q: 6. Four cylinders rolling in opposite directions has a speed ratio of AB.C:D = 5:2:3:4. If center…

A: Let the diameters of each cylinders be - DA, DB, DC and DD . The center distance is given by -DA2+…

Q: 19.3. A series of cold rolling operations are to be used to reduce the thickness of a plate from 50…

Q: Show your illustration and complete solution in a drawing plate. Two parallel shafts, 11 inches…

Q: A 300-mm-wide strip 25-mm thick is fed (Bottom roll removed) through a rolling mill with two powered…

A: Given: The width of strip, b = 300 mm The thickness of strip, x = 25 mm The radius of rolls, R = 250…

Q: A strip with a cross section 120 mm x 6 mm is being rolled with 20% reduction area, using rolls of…

Q: Two parallel shafts, 27 inches apart and having a speed ratio of 2.6 are connected by cylinders in…

Q: A cylindrical working part is subjected to a forging landfall operation. The blank is 3.0 in. high…

A: volume of workpiece=π4×22×3=9.4247 in3

Q: The method of sheet forming in which springback is prevented is called .......... n) With the help…

A: Given :- m) The method of sheet forming in which springback is prevented is called ..........n)…

Q: A 42.0 mm-thick plate made of low carbon steel is to be reduced to 34.0 mm in one pass in a rolling…

A: *As per our guidelines we are supposed to answer* only one question. Kindly repost other questions…

Q: Two parallel shafts, 11 inches apart and rotating at 75 RPM and 200 RPM are connected by cylinders…

Q: In rolling process, calculate the applied torque in (N.m) when w= 600mm, K = 275 MPa, n = 0.10, %3D…

A: Given Data W=600 mm K=275 MPa n=0.1 ho=35 mm hf=29 mm R=373.3 mm

Q: An aluminium strip with a cross section of 200 mm × 8 mm is being rolled with 25% reduction of…

A: Given Data: Aluminium strip cross sectional area A=200 mm×8 mm Diameter d=400 mm Tensile yield…

Q: A strip with a width of 12 in. And 1 in. Thick is fed through a rolling mill with rolls of 10 in.…

Q: A strip with cross section 120 X 6 mm is being rolled with 20 % reduction area, using rolls of…

A: Consider a strip of thickness h0 is undergone rolling operation whose Roll Diameter is D and angle…

Q: Determine the direction of slip line at the workpiece tool interface in the condition of coulomb…

A: given; ⇒coefficient of friction (μ)=0.2⇒normal stress (σ)=100N/mm2⇒shear yield strength…

Q: Two shafts, having axes in the same plate intersecting at an angle of 40°, turn in the same senses…

Q: 6.Where is instant center of a higher pair of rolling and sliding ? A lies at infinity on the normal…

A: As per given question .Where is instant center of a higher pair of rolling and sliding

Q: Compare the force required to draw (25mm×6mm) capper strip to 45% reduction of area with that…

Q: Calculate the bite angle when rolling plates 12 mm thick using work rolls 600 mm diameter and…

A: Given:∆h, Thickness reducing=3 mmR, radius of roller=300 mm

Q: A 42.0-mm-thick plate made of low carbon steel is to be reduced to 34.0 mm in one pass in a rolling…

Q: The team is rolling a 300-mm-wide strip 25-mm thick with two powered rolls each of radius = 250 mm…

A: Since you have posted a question having multiple subpart we will solve first three part for you To…

Q: the work metal has a flow curve defined by K=300MPa and n=0.2, and the coefficient of friction…

Q: Calculate the bite angle when rolling plates 12mm thick using work rolls 600mm diameter and reducing…

A: Given data: hi=12 mm∆h=3 mmD=600 mm Need to determine the bite angle.

Q: A 300-mm-wide strip 25-mm thick is fed through a rolling mill with two powered rolls each of radius…

A: Let b =width =300mm h1 =Thickness before passing to roller =25mm h2 =Thickness after passing to…

Q: 3. Two shafts, having axes in the same plate intersecting at an angle of 45°, turn in opposite…

A: Given: θ=45°,N1 = 30 rpm , N2 = 90 rpm , r2 = 1 inch To find: cone angles, i.e. γγ1 , γ2 Solution:…

Q: I. Using smaller diameter rolls, to reduce the contact area II. Taking smaller reductions per pass,…

Q: Explain the significance of rolling disc on inclined plane apparatus.

Q: ng at 75 RPM and 200 RPM, are connected by cylinders in pure rolling contact. Determine the…

Q: Neutral point (no-slip point) of the rolling is a point along the arc in which the workpiece and…

A: In rolling operation. The velocity of workpiece and velocity of roller are same at a point. I.e…

Q: forming proceɛɛ. 18) rolling mill type are associated with relatively small diameter rolls in…

A: Disclaimer from Bartleby: Since you have asked multiple question, we will solve the first three…

Q: Fill in the blanks: Find the distance in (inches) of the shafts if the small cylinder is 88 inches…

Q: The thickness of a metallic sheet is reduced from an initial value of 16 mm to a final value of 10…

A: Data given- T1 = 16 mm T2 = 10 mm D = 400 mm So R = D/2 = 400/2 = 200 mm

Q: Two parallel shafts, 11 inch apart and rotating at 75 rpm and 200 rpm are connected by cylinders in…

Q: 7. A strip of annealed low-carbon steel (K = 528 MPa, n = 0.25) is rolled from its initial…

Q: nore ects in rolling

A: 1. Iron ore: Iron metal is a mineral substance which, when warmed within the sight of a reductant,…

Q: mention the advantages and disadvantages of rolling contact bearing

A: Rolling contact bearings: In rolling contact bearings, the contact between the bearing surfaces is…

Question

100%

First problem only. Read and Solve carefully, make sure readable if it is in hand written form, include the units in every step. Your work will be appreaciated much. Thanks! See attached figure for the problem.

3. Two shafts, having axes in the same plate intersecting at an angle of 45°, turn in opposite
senses at 30 rpm and 90 rpm. Draw a pair of cone to be located on these shafts and turn in
pure rolling contact. Diameter of base of smaller cone is 1 in. Calculate the cone angles.
4. Two shafts A and B are connected by rolling cones and turn in the same direction. Shaft A
makes 300 rpm while shaft B makes 100 rpm. Calculate the cone angle of each cone and
the diameter of each base if the base of cone B is 2 in. from the vertex. 0 = 30°

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Please solve this, thank you very muchProblem: Two parallel shafts, 27 inches apart and having a speed ratio of 2.6 are connected by cylinders in pure rolling contact. Find: 1. diameter of larger cylinder when they turn in the opposite direction 2. diameter of smaller cylinder when they turn in the opposite direction 3. diameter of the larger cylinder when they turn in the SAME direction
Problem 6 only, solve carefully, include the units in every step and draw the diagram. Thanks! Four cylinders rolling in opposite directions has a speed ratio of A:B:C:D = 5:2:3:4. If center distance between cylinderA and D is 80 inches, find the diameter of all cylinders
Board Exam April 1997. Two parallel shafts connected by pure rolling turn in the same direction having a speed ratio of 2.75. What is the distance of the two shafts if the smaller cylinder is 22 cm in diameter?
Question 3A rolling operation on a 250 mm wide, 8 mm thick, 1112 cold rolled steel takes place using hardened steel rolls with a surface finish of 0.03 μm. The rolls have a diameter of 350 mm and rotates at 115 rpm. The final thickness of the plate is 6 mm and the entry speed of the plate is 1.8m/s Calculate: 3.1)The minimum coefficient of friction required, that will make the rolling operation possible. 3.2 The required roll force. 3.3 The position of the neutral point, ??3.4 Indicate, using a sketch, the neutral point showing all relevant notation and dimensions
If two parallel shafts are connected by cylinders in pure rolling contact and turning in the same direction, and having a speed ratio of 2.75, what is the Center distance of the two shafts assuming that the diameter of the smaller cylinder is 22 cm? Unit in cm.
A rolling cone with a center angle of 15° turning at 240 rpm makes external contact with the second one which turns at 360 rpm. Find the angle between the shafts.
Correct Solution need.. Two parallel shafts, 61 cm apart and having a speed ratio of 3, are connected by cylinders in pure rolling contact. Determine the D1 in cm, when they turn in same directions.
Illustrate what happens when a torque is applied to a circular shaft?
Two parallel shafts, 11 inches apart and rotating at 75 RPM and 200 RPM, are connected by cylinders in pure rolling contact. Determine the diameters of the cylinders: (1) when they turn in opposite directions; and (2) when they turn in the same direction.
Draw the figure and show your solutions. PLEASE ANSWER IT ASAP FOR AN UPVOTE. Shafts A and B are connected by rolling cones and are turning in the same direction. A makes 450rpm while B makes 150rpm. Angle between them is given as 45°. Calculate the cone angle of each cone and the diameter of each base if the base of cone B is 5inches from the vertex
in shaft turning Steel raw material, diameter 40 mm., length 200 mm. to obtain a lathe workpiece diameter 35 mm., length 150 mm, as shown in the figure, with a cutting speed of 25 m/min and a rough-cutting feed rate (f) 0.2 mm/rev. The feed rate for finishing (f) 0.1 mm per revolution determines a depth for rough turning of not more than 1 mm and a depth for finishing of not more than 0.5 mm. Find 1) the speed of rotation used per minute. 2) Details of turning Such as how many rounds of rough turning, how many rounds of fine turning? 3) From the available data Find the approximate turning time in minutes.
On the attached drawing, is the allowance between "shaft C" and "hole D" positive or negative?