Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be limited to 188 MPa, determine the minimum diameter required for each rod. Assume P = 81 kN and Q = 108 kN.

Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be limited to 188 MPa, determine the minimum diameter required for each rod. Assume P = 81 kN and Q = 108 kN.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.13P: A metal bar AB of a weight Ills suspended by a system of steel wires arranged as shown in the...

See similar textbooks

Related questions

Q: An aluminum [E = 10000 ksi] control rod with a circular cross section must not stretch more than…

Q: The cross-sectional area of bar ABCD is 500 mm?. Determine the stress in segment BC. 40 kN 35 kN 20…

Q: The rectangular beam ABC, 100 mm wide by 400 mm deep, is supported by a pin at A and the cable CD.…

A: Given data :- width of beam = 100mm depth of beam = 400mm normal stress in the beam = 120 Mpa. find…

Q: Member BC shown is subjected to a vertical force of 45 kN. Determine the position S of this force so…

Q: For the clevis connection shown, the shear stress in the 0.21-in.-diameter bolt must be limited to…

A: Given: Let us consider the given data, Shear stress, τ=39 ksi=39×103 Psi Bolt's diameter, d=0.21 in…

Q: Required information Two horizontal 9.5-kip forces (P) are applied to pin B of the assembly shown. A…

A: Given P = 9.5 kip Diameter of pin = 0.8 in To find Normal stress at link AB

Q: A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138, Determine…

A: Solution (A) Given data: The inside diameter of the steel tube, d1 = 120 mm. The outside diameter…

Q: A stainless steel tube with an outside diameter of 50 mm and a wall thickness of 5 mm is used as a…

Q: An open cylindrical tank E mm in diameter and made of F mm thick plate is subjected to an internal…

A: According to the given information we have a diameter of the cylinder is 6 mm. the thickness of the…

Q: 4. A force Q is applied to a rectangular member with a size of 300mm x 450mm. Q is located 37-5mm…

A: Find the value of force Q and stress at point C and D

Q: PROBLEM 2) The rigid bar ABC shown is hinged at A and supported by a steel rod at B. 8) Determine…

A: Givenσ=120MPa∆xc=4mm

Q: The homogeneous bar ABCD shown in figure below is supported by a cable that runs from A to B around…

Q: a. The diameter of the connecting rod CD, given that the normal stress is limited to 140 MPa. b. The…

A: Given: P1= 5 kN Normal stress = 140 MPa To determine: The diameter of connecting rod CD The shear…

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. Determine the largest load…

Q: The homogeneous bar ABCD shown in Fig. is supported by a cable that runs from A to B around the…

Q: A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three…

Q: 3 a M The scheme of supporting of the absolutely rigid body is shown in the picture. The minimal…

A: Given data: The value of a is a = 1.6 m. The magnitude of the moment is M = 8 kN-m. The admissible…

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

Q: An aluminum [E = 10100 ksi] control rod with a circular cross section must not stretch more than…

Q: A vertical force P is applied at a point C located on the axis of sym-metry of the cross section of…

A: The centroid of the column , y=y1A1+y2A2A1+A2 iny=5X6X2+2X4X26X2+4X2 iny=3.8 in

Q: Rigid bar ABC supports a weight of W = 26 kN. Bar ABC is pinned at A and supported at B by rod (1),…

A: Free body diagram

Q: A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three…

A: given data; ⇒a=1.2m⇒b=7.9m⇒c=2.9m⇒load(P)=40KN⇒load(Q)=75KN⇒area(A)=1120mm2⇒normal stress in each…

Q: The structure supports a distributed load of w. The limiting stress in rod (1) is 300 MPa, and the…

A: Given:

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

A: For the Given system P = 9 kips Q = 5 kips R = 20 kips S = 30 kips stress limit in (1) = 19 ksi…

Q: An aluminum [E-9600 ksi] control rod with a circular cross section must not stretch more than 0.34…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If the…

A: Given data: σ=345 MPa Need to determine the minimum diameter required for the rod.

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the…

Q: 5. The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported…

Q: QUESTION 2 с Y The 6.7-in diameter steel shaft AB is attached into the rigid wall at C and supported…

A: Given data: ◆ The dia meter of the shaft: d = 6.7 in ◆ The length of the lever AC: x = 3.54 ft ◆ The…

Q: A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three…

Q: If the allowable bearing stress for the material under the supports at A and Bis op = 820 psi,…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the…

Q: Rigid bar ABC supports a weight of W 50 kN. Bar ABC is pinned at A and supported at B by rod (1),…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

Q: Required information Two horizontal 5.5-kip forces (P) are applied to pin B of the assembly shown. A…

Q: A 600 kg material is hung from the end of the horizontal bar BD as shown. Determine the stress on…

Q: 2.2 (A). If the maximum stress allowed in the copper of the cabie of problem 2.1 is 60 MN/m?,…

A: Given, The diameter of a single copper wire, d=1.6 mm No. of wires are 10 and there are such three…

Q: A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three…

Q: A 150mm x 30mm x 250mm central wooden block is glued between cantilevered brackets 200mm x 50mm each…

A: Stress Stress is defined as the ratio of force to the area on which force is acting. There are…

Q: Two aluminum plates, each having a width of b = 8.0 in. and a thickness of t = 0.750 in., are welded…

Q: Q3) A pillar crane, shown in below, is fastened to the foundation by means of 16 identical bolts…

Q: Q6/ For the truss in Q5, if the average normal stress in cach of the 25-mm diameter bars is not…

Q: vo solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the…

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

A: Given:-A=3.9 in2a=4.25 ftb=5.10 ftNormal stress=55ksiTo find:-Pmax

Q: 2. For the bone shown to the left, assume the cross-section at C can be approximated as annular,…

A: Given:Average normal stress, σ=3.8 MPaLoad applied, P=1200 Nouter diameter, d=25 mm

Q: The steel tie bar shown is to be designed to carry a tension force of magnitude P = 130KN when…

Q: Q. 6: A steel rod 20 mm in diameter, 400 mm long is co-axially enclosed in brass tube of 25 mm…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be
limited to 188 MPa, determine the minimum diameter required for each rod. Assume P = 81 kN and Q = 108 kN.
d2
di
В
C
Answers:
d1 =
i
%3D
mm.
d2 =
i
mm.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
, An arm A BC lying in a horizontal plane and supported at A (see figure) is made of two identical solid steel bars AB and BC welded together at a right angle. Each bar is 22 in. long. (a) Knowing that the maximum tensile stress (principal stress) at the top of the bar at support A due solely to the weights of the bars is 1025 psi, determine the diameter d of the bars. (b) If the allowable tensile stress is 1475 psi and each bar has a diameter d = 2.0 in,, what is the maximum downward load P that can be applied at C(in addition to self-weight
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
Because of foundation settlement, a circular tower is leaning at an angle a to the vertical (see figure). The structural core of the tower is a circular cylinder of height ft, outer diameter d2, and inner diameter d1.For simplicity in the analysis, assume that the weight of the tower is uniformly distributed along the height. Obtain a formula for the maximum permissible angle a if there is to be no tensile stress in the tower.
A steel pad supporting heavy machinery rests on Four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression in 50 ksi. The outer diameter of the piers is d = 4.5 in, and the wall thickness is t = 0.40 in. Using a factor of safety of 3.5 with respect to the ultimate strength, determine the total load P that can be supported by the pad.
An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.
A slightly tapered bar AB of solid circular crass section and length L is supported at end B and subjected to a tensile load P at the free end A. The diameters of the bar at ends A and B are dAand dB. respectively. Determine the length of the bar if the elongation of the bar due to the load P = 45 kips is 0.02 in. Assume that E = 10,400 ksi.
A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the top of a vertical buttress AB (see figure). The vertical buttress has height h = 5.0 m and rectangular cross section of thickness t = 1.5 m and width b = 1.0 m (perpendicular to the plane of the figure). The stone used in the construction weighs y = 26 kN/m3. What is the required weight W of the pedestal and statue above the vertical buttress (that is, above section A) to avoid any tensile stresses in the vertical buttress?
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.