Two tubular sections shown in Figure-2, have the same wall thickness and same circumference. Neglecting the stress concentration, find the ratio of shear stresses for equal twisting moments for two cases. a t - 2 1

Two tubular sections shown in Figure-2, have the same wall thickness and same circumference. Neglecting the stress concentration, find the ratio of shear stresses for equal twisting moments for two cases. a t - 2 1

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.1P: A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer...

See similar textbooks

Related questions

Q: 30KN 20 KN 2m By 2m D 2m

Q: The 490-lb beam is supported at A and B when it is subjected to a force of P= 1000 lb as shown.…

Q: For a steady flow process, the rate of change in the total energy of the system will be zero. Select…

Q: 50 R20

A: The semi cut side projection with dimension is shown below.

Q: below, what is the rotation of rod AB about point A if piston b moves to the right? Moreover, what…

A: vB=7.5m/saB=18.75m/s2 To-Find:- Angular-Acceleration=?

Q: In the situation illustrated in the figure below, a small package is deposited by a conveyor belt at…

Q: kg/s of a gas passes through a unit of 0.6 reversible steady flow. It rejects heat rate about 50…

Q: Three plain-carbon steel types are: eutectoid, hypoeutectoid, and hypereutectoid can be seen in the…

Q: At room temperature, the water in the storage tank is pumped up to the top of the absorption tower…

Q: What flow rate at 4000 lbf/in.2 would it take for a hydraulic motor to deliver 20 FHP?

A: Pressure= 4000 lbf/in^2 Fluid power= 20 FHP To find; Flow rate

Q: Calculate the moment of inertia of the shaded area about the x-axis. 97 mm 97 mm 60 mm Answer: Ix =…

Q: Q1: The machine part of negligible weight is supported by a pin at A and a rolier at Cas shown in…

A: Find the reactions.

Q: A glass capillary tube of diameter 0.3 mm and length 60 mm is dipped in a water having surface…

A: Given datadiameter of capillary tube = d = 0.3 mm = 0.3 x 10-3 mLength of capillary tube = L= 60 mm…

Q: Write the shear and moment equations and draw the shear and moment diagram

Q: Determine the coordinates of the centroid of the area that lies between the straight line x =2y/3…

A: Given: equation of straight line→x=2y3 And equation of parabola→x2=4y (1): Using horizontal…

Q: 3. For a beam in bending, what is a suitable Airy Stress Function? Why?

A: given; for a beam in bending ,what is suitable airy stress function? why?

Q: A large home ice cream maker is being used to freeze ice cream. The bowl is at -15C, having just…

A: Find the temperature of the ice cream mix.

Q: A steam power plant operates on a Rankine cycle. Steam enters the turbine at 600 F and 15 MaP and…

A: Given data Steam enters the turbine at 600°F and 15 MPaSteam exits the turbine at 15 kPaTurbine…

Q: Same situation as before. This time it s a block of mass 1.21 kg sliding with a constant velocity of…

A: Given Data The mass of block 1 is:m1=1.21kg The velocity of block 1 isu1=3.27 m/s The mass of…

Q: Consider saturated liquid water at 100°C, contained in a piston-cylinder device. It is then…

Q: ample 2: Convert the quantities 300 lb.s and 52 slug/ft' to appropriate SI units.

Q: A U-tube manometer contains a liquid having a 3 density of 800 kg/m. When the manometer is connected…

Q: Technician A believes the stall test damages transmissions. This includes the torque converter…

A: Stakk test is a short time full-throttle operation with the vehicle brakes fully applied and the…

Q: Write the shear and moment equations and draw the shear and moment diagram:

Q: Q2: Determine the X-and y- coordinates of the centroid of the shaded area amm 20mm 6omm

Q: Example 15: Locate the center of mass of the bracket-and-shaft combination. The vertical face is 50…

Q: A loop antenna of area A = 3.98 cm2 and resistance R = 6.41 µn is perpendicular to a uniform…

A: Find the thermal energy produced.

Q: 2) A linear elastic SDOF system is given below with Tn= 1.1 s, m 1 kg, & = 5 %, u(0) = 0, ú(0) = 0.…

A: Given : To find : Displacement response

Q: Q2/ Determine the forces at the pin joint (F) and the roller support (G) ? 20 KN 30KN 2m By 2m D 2m…

Q: An uncontrolled 850 kg car strikes squarely a motorway crash cushion in which the car is brought to…

Q: ample 2: Convert the quantities 300 lb.s and 52 slug/ft to appropriate SI units.

Q: 1. A two dimensional supersonic airfoil has the cross-section shown below (base: 2.8 m, base angles…

A: Given Mach number, M = 2.4 Pressure, P = 25 kPa Base, w = 2.8 m…

Q: According to first law of . thermodynamics work done by a system is equal to heat transferred by the…

A: There are 3 laws of thermodynamics: 1.Zeroth law of thermodynamics 2. First law of thermodynamics 3.…

Q: (iii) The shear force in a beam subjected to pure positive bending is a) Positive b) Negative c)…

A: To select the correct option for the given sentence

Q: A bicycle and rider of mass 120 kg are travelling at a speed of 15 km/hr on a level road. The rider…

Q: 1- Select the optimum choice for: high speed air craft skins material. Table 1: The properties of…

A: The most extensively used aluminium alloy in aircraft development is 2024. The alloy is a…

Q: which of the PlMowing matricas are singula Por the non sin fnd the in verse? 13 3. 2) -2 2. 12 3 3.…

Q: A volume of 0.03 m' of O, mi larally at 220 F and pressure 4 bar is compressed reversibly at…

Q: b- A vapour compression refrigerator uses refrigerant (R- 410a) and operates between temperature…

Q: A gas turbine power plant operating on a Brayton cycle takes in atmospheric air at 16°C. The…

Q: 50 R20 20

A: the semi cut side projection of given figure is shown below.

Q: Drive Shaft Simulation

A: Your vehicle's drivetrain system helps you get down the road, from trucks and SUVs to small cars…

Q: 1. For the siphon given in the figure calculate a) The volume flow rate of water through the nozzle…

Q: 5. A 5kg ball is moving along a frictionless elliptical rod from B to A. one end of the spring is…

A: Soln Mass of ball = 5 kg System is frictionless ( energy conservation) At A & B Total energy at…

Q: Drive Shaft G-Codes programming process

A: Given question: Drive Shaft G Code programming process. The given question is related to…

Q: Q1/ In the equilibrium position shown in figure below, the uniform bar (AB) has a mass of (50 kg)…

A: Answer: Option (C): T = 7646 N, FBx = 3823 N , FBy = 4169 N

Q: Numerical Exercise 1. A flat plate is supplied with a constant heat flux of 100 [W/m2] from bottom.…

Q: Q4: The 2-Mg uniform pole in Fig.4 is supported by a ball-and -socket joint and two cables.…

A: Find the tension in the cables .

Q: Show your calculation for the method 2 velocity. Explain how it compared to the reading from your…

A: Write the given data from the table. t1=5 sx1=11 mt2=6 sx2=17 m

Q: For the 3500-lb car, determine (a) its mass in slugs, (b) its weight in newtons, and (c) its mass in…

A: Given: W= 3500 lb To find: Weight of the car in Slugs Newtons Kg

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

4. Two tubular sections shown in Figure-2, have the same wall thickness and
same circumference. Neglecting the stress concentration, find the ratio of
shear stresses for equal twisting moments for two cases.
t
a
t >
2
1
Figure-2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A steel hanger bracket ABCD has a solid, circular cross section with a diameter of d = 2 in. The dimension variable is b = 6 in. (see figure). Load P = 1200 lb is applied at D along a line DIh the coordinates of point H arc (8/>, — 5b, 2b), Find normal and shear stresses on a plane stress element on the surface of the bracket at A. Then find the principal stresses and maximum shear stress. Show each stress state on properly rotated elements
A torque T is applied to a thin-walled tube having a cross section in the shape of a regular hexagon with constant wall thickness t and side length b (see figure). Obtain formulas for the shear stress rand the rate of twist
‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.
A solid aluminum bar (G = 27 GPa ) of diameter d = 40 mm is subjected to torques T = 300 N - m acting in the directions shown in the figure, Determine the maximum shear, tensile, and compressive stresses in the bar and show these stresses on sketches of properly oriented stress elements. Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements.
A circle of a diameter d = 200 mm is etched on a brass plate (see figure). The plate has dimensions of 400 x 400 x 20 mm. Forces are applied to the plate, producing uniformly distributed normal stressescr^ =59 MPaander^ = —17 MPa. Calculate the following quantities: (a) the change in length Aac of diameter at: (b) the change in length Abd of diameter bd; (c) the change At in the thickness of the plate; (d) the change AV in the volume of the plate; (e) the strain energy U stored in the plate; (f) the maximum permissible thickness of the plate when strain energy £/must be at least 784 J; and (g) the maximum permissible value of normal stress axwhen the change in volume of the plate cannot exceed 0.015% of the original volume. (Assume E = 100 GPa and v = 0.34
At a point on the web of a girder on a gantry crane, the stresses acting on the x face of a stress element are s= 6250 psi and ??xy= 1425 psi (see figure). What is the allowable range of values for the stress ??. if the maximum shear stress is limited to t0 = 2150 psi?
A single steel strut AB with a diameter (a) Find the strut force Fs and average normal stress ds= 8 mm supports the vehicle engine hood of a in the strut. mass 20 kg that pivots about hinges at C and D (see (b) Find the average shear stress t aver in the bolt at A,figure parts a and b). The strut is bent into a loop at (C) Find the average bearing stress bon the bolt at A. its end and then attached to a bolt at A with a diameter db= 10 mm. Strut AB lies in a vertical plane.
A cold-formed steel section is made by folding a steel plate to form a structural section such as that shown in the figure. This beam is subjected to bending moment M = 2 kip-in, at angle 0 = 10º to the z axis. Find the centroid and the orientation of the neutral axis. Find flexural normal stresses at points A and B (see figure). Use the flexure formula based on principal axes and then confirm your solution using the general flexure formula. Hint: the plate is thin so use centerline dimensions.
Acting on the sides of a stress element cut from a bar in uniaxial stress are tensile stresses of 10,000 psi and 5000 psi, as shown in the figure. (a) Determine the angle 0 and the shear stress T and show all stresses on a sketch of the element. (b) Determine the maximum normal stress amaxand the maximum shear stress Tmax in the material.
A gondola on a ski lift is supported by two bent arms, as shown in the figure. Each arm is offset by the distance b = ISO mm from the line of action of the weight force W. The allowable stresses in the arms are 100 MPa in tension and 50 MPa in shear. If the loaded gondola weighs 12 kN, what is the minimum diameter roof the arms?
3-17 The stresses at a point along a beam supporting a sign (see figure) are sx= 2250 psi, sy,. = 1175 psi, and txy = -820 psi. (a) Find the principal stresses. Show them on a sketch of a properly oriented clement. (b) Find the maximum shear stresses and associated normal stresses. Show them on a sketch of a properly oriented element.
Repeat the preceding problem but now find the stress state on Element A at the base. Let W%= 240 N, WL= 250 N, / = 5 mm, d = 360 mm. See the figure for the locations of clement A and all loads