Two vertical forces are applied to a simply supported beam with the cross-section shown. If L1 determine the maximum tension bending stress in the beam. The beam's moment of inertia about the z axis is 10,577,574 mm“, and the centroid of the section is located 139.1 mm above the bottom surface of the beam. 200 mm 15 mm 160 mm L1 L2 L1 9 mm O 236.7 MPa O 152.0 MPa O 176.1 MPa O 280.4 MPa O 224.3 MPa

Two vertical forces are applied to a simply supported beam with the cross-section shown. If L1 determine the maximum tension bending stress in the beam. The beam's moment of inertia about the z axis is 10,577,574 mm“, and the centroid of the section is located 139.1 mm above the bottom surface of the beam. 200 mm 15 mm 160 mm L1 L2 L1 9 mm O 236.7 MPa O 152.0 MPa O 176.1 MPa O 280.4 MPa O 224.3 MPa

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

If M, = 285 kip-ft, find the magnitude of the bending stress at a point H For the beam cross section, assume a = 9 in. b= 12 in. d= 31 in r= 45 in. The centroid of the cross section is located 14.16 in. below the uppermost surface of the beam. The moment of inertia about the z axis is 26227 in 4
The internal shear force V at a certain section of a steel beam is 80 kN, and the moment of inertia is 64,867,500 mm4. Determine the horizontal shear stress at point H, which is located L = 17 mm below the centroid. 58.9 MPa 42.7 MPa 39.6 MPa 35.2 MPa 31.2 MPa
The T-shaped beam shown above is supporting a concentrated load P at its free end. The beam has an allowable bending stress of ?????? = 250 MPa and an allowable shear stress of ?????? = 100 MPa. a) Determine the distance to the neutral axis (?̅), second moment of area (?), and the section modulus (?) of the cross-section.b) Draw the shear force diagram (SFD) and bending moment diagram (BMD) of the beam. On your diagrams, express the values of shear and moment in terms of the applied load P.c) Determine the maximum value of P such that bending failure will not occur.d) Determine the maximum value of P such that shear failure will not occur.e) Based on your answers to (c) and (d), what is the maximum load P that can be applied to the beam? Is this beam bending or shear governed?
Consider a 180-mm-long segment of a simply supported beam. The internal bending moments on the left and right sides of the segment are 60 kN-m and 68 kN-m, respectively. The cross-sectional dimensions of the flanged shape are shown in the accompanying figure. Assume b1 = 120 mm, b2 = 30 mm, b3 = 200 mm, d1 = 65 mm, d2 = 175 mm, d3 = 65 mm. Determine the maximum horizontal shear stress in this segment of the beam.
If d = 450 mm, determine the absolute maximum bending stress in the overhang beam.
Consider a 155-mm-long segment of a simply supported beam. The internal bending moments on the left and right sides of the segment are 75 kN-m and 79 kN-m, respectively. The cross-sectional dimensions of the flanged shape are shown in the accompanying figure. Assume b1 = 135 mm, b2= 50 mm, b3= 205 mm, d1= 65 mm, d2= 180 mm, dz= 65 mm. Determine the maximum horizontal shear stress in this segment of the beam.
A simply supported beam carries a concentrated load of 31 kN at 7 meters from the left support (1 meters from the right support). Use EI = 80,000 kN-m2. Solve for the slope at the left support in degrees.
Since the beam M in the figure is under the effect of simple bending moment, calculate the bending stress and shear stress values at the A, B and C points. h = 400mm b = 140mm and M = 150KNm
1-10. A bar of variable cross section, held on the left, is subjected to three forces, P =4 kN, P, = -2 KN, and P, = 3 kN, as shown in the figure. On two separate diagrams, plot the axial force and the axial stress along the length of the bar. Let A1, = 200 mm, A2, = 100mm², and A3, = 150 mm".
3.) For the given couple-force system shown, determine the horizontal component of Q. P= 335 KN Q= 44 KN R=74 KN-m Z=263 KN
From the given simply supported beam below, determine the following: d. The moment of inertia with respect to the neutral axis. e. The maximum flexural stress and shear stress of the beam. f. The bending stress at point B and C.
The figure which is in equilibrium under the forces P and F = 42 kN inclined at θ= 48o, is supported by a pin at D. Determine the shear stress in the pin if it is 21-mm-diameter.