Two water reservoirs are connected by a cast iron pipeline which is 150 mm in diameter for the first 6 m and 225 mm diameter for the remaining 15 m as shown in Figure 1. The entrance and exit are square-edged. If the discharge is 0.185 m³/s and dynamic viscosity of water is 0.00102 Ns/m², determine the various losses along the pipeline.

Two water reservoirs are connected by a cast iron pipeline which is 150 mm in diameter for the first 6 m and 225 mm diameter for the remaining 15 m as shown in Figure 1. The entrance and exit are square-edged. If the discharge is 0.185 m³/s and dynamic viscosity of water is 0.00102 Ns/m², determine the various losses along the pipeline.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water flows at a rate of 0.8 cumecs in a 900 m-long pipe with a total head loss of 4m. Solve for the pipe diameter in mm by, (a) By Darcy - Weisbach formula with f = 0.018; (b) Manning's formula with n = 0.014; and (c) Hazen-Williams formula with C = 130.
Answer only that first question thanks. A rectangular canal 3.2 m wide and 1.2 m deep has a full capacity of 8.5 m3/s. Assuming n = 0.015 what is the slop of thechannel bed? Water is issued vertically at the rate of 35 L/s through a 60 mm diameter nozzle. What is the the maximum height of water can reach.
A distributary channel having bed width 5.00 m and full supply depth of1.50 m carries 3.0 m3/s of discharge. A semi-modular pipe outlet in this channel has a commandarea of 15 ha growing rice with a kor depth 20 cm and kor period of three weeks. Determine thesize of the outlet and set it for sub-proportionality with a flexibility of 0.9. Assume the lengthof the pipe as 3.0 m and friction factor as 0.03. The available diameters of the pipe are 150, 125,100, and 75 mm.How does this outlet behave if the distributary runs below FSL at 1.0 m depth ?
Hydrology engineering Q5. well with a radius of 0.5m , completely penetrates an unconfined aquifer of thickness 50m and K=30m/day .the well is pumped so the water level in the well remains at 40m above the bottom .Assuming that the pumping has essentially no effect on water table at R=500m ,what is the steady state discharge ?
A rectangular channel is 6.3 m wide and has depth of flow of 1.7m. The slope of the channel bed is 1/1000. The material used to line the channel is known to have a Ch = 49m^(1/2) m/s. Calculate the mean velocity & discharge.
Give me right solution You have designed a 16-in diameter stormwater pipe to flow at a velocity of 5 ft/s when full. The Manning’s roughness coefficient is 0.011. What material is most likely the pipe made of and what is the slope of the energy grade line?
Three reservoir A, B and C have elevations of 30 m., 24 m. and 15 m. respectively. PointD is the junction of the three pipelines coming from A, B and C respectively. Pipe 1 from A to D is1200 m. long, with diameter of 300 mm. Pipeline 2 is 900 m. from B to D and has a diameter of 200mm and pipeline 3 is 1500 m. from C to D with a diameter of 150 mm. water to reservoirs b and c atthe rate of 44 liters/sec. How much water is distributed to reservoir B if n = 0.011 for all pipes. determine the discharge to reservoir C ifn = 0.011 for all pipes.
Water 20°C, flows at a rate of (0.05 m3/sec) in (20-cm) asphalted cast-iron pipe. What is the head loss per Kilometer of the pipe, if the Kinematic viscosity of water (v= 1.0 x 10* m2/sec) , and friction factor in the pipe (f= 0.019) ?
A 200 mmФ pipeline whose length and friction factor (f) are 2.5 km and 0.018 respectively connects two tanks A and B. Assuming minor loss to be 10% of friction loss, and reservoir A 15 m higher than B, find the rate of flow * a. 0.03426 m³/s b. 0.05426 m³/s c. 0.04426 m³/s d. 0.06426 m³/s
Water flows through the pipe shown at 5 liters per second. If gage pressures of 12.5 kPa, 11.5 kPa and 10.3 kPa are measured for p1, p2, and p3 respectively, compute the head losses in m between; (a) 1 and 2, (b) 1 and 3, and (c) 2 and 3
A uniform pipeline, 5000 m long, 200 mm indiameter and roughness size (ε) 0.03 mm, conveys water at15 oC (ν = 1.13x10-6 m2/s) between two reservoirs, thedifference in water level is maintained at 50 m. In addition tothe entry loss of 0.5v2/2g and an exit loss k = 1.0. Determine the steady discharge between reservoirs usinga. Colebrook-White equationb. Explicit function of f
Three reservoirs A, B, and C are connected by pipelines 1, 2, and 3 respectively which merges at a junction X. The elevation of reservoir A is 300 m and that of B is 285 m. The rate of flow from reservoir A is 1.4 m3/s. Pipes 1 (D = 800 mm, L = 1500 m, Friction Factor = 0.0157) Pipes 2 (D = 600 mm, L = 450 m, Friction Factor = 0.0162) Pipes 3 (D = 450 mm, L = 1200 m, Friction Factor = 0.0177) Compute the elevation of reservoir C in m. Round your answer to 2 decimal places.