Two wood beams, each of rectangular cross section (3.0 in. x 4.0 in., actual dimensions), are glued together to form a solid beam with dimensions 6.0 in. x 4.0 in. (see figure). 4.0 in 6.0 in. 8 ft- Ⓡ The beam is simply supported with a span of 8 ft. (a) What is the maximum moment Mmax (in kip-ft) that may be applied at the left support if the allowable shear stress in the glued joint is 175 psi? (Include the effects of the beam's own weight, assuming that the wood weighs 35 lb/ft³. Enter the magnitude.) kip-ft (b) Repeat part (a) if Mmax is based on allowable bending stress of 2,510 psi. kip-ft

Two wood beams, each of rectangular cross section (3.0 in. x 4.0 in., actual dimensions), are glued together to form a solid beam with dimensions 6.0 in. x 4.0 in. (see figure). 4.0 in 6.0 in. 8 ft- Ⓡ The beam is simply supported with a span of 8 ft. (a) What is the maximum moment Mmax (in kip-ft) that may be applied at the left support if the allowable shear stress in the glued joint is 175 psi? (Include the effects of the beam's own weight, assuming that the wood weighs 35 lb/ft³. Enter the magnitude.) kip-ft (b) Repeat part (a) if Mmax is based on allowable bending stress of 2,510 psi. kip-ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

f) the maximum bending moment in the beam. Enter your answer in kNm to 3 decimal places.
Calculate the maximum moment in beam for six moving loads.
A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. Calculate the depth of the neutral axis of the section in PART A in mm.0 Calculate the ultimate moment capacity of the section in PART A in kN.m.0 Calculate the effective depth of the section in PART B in mm.0
Replace the force system acting on the beam by an equivalent force and couple moment at point A.
In the overhanging beam show, determine P so that the moment over each support equals the moment at the midspan. w = 4.6 kN/m i need an answer right away. thank you
For the beam and loading shown, calculate the maximum moment in the beam. 312.5 N.m 503.2 N.m 187.5 N.m 351.5 N.m
For Beam 2, what is the Maximum Moment for the entire beam?
Draw the FBD of the shaded beam, assuming: • Live load = 50 psf • Slab dead load = 70 psf (excluding beam weight) • T-Beam: b =30 in. and h = 40 in. Then solve for the reactions of joists on main beams, and main beams on columns.
Calculate the ultimate moment capacity of a rectangular beam with b = 300 mm, d = 500 mm, As= 5400 mm2• Assume fc = 34 MPa, fy = 414 MPa.
Refer to the given figure below and compute for moment at force C -- (CW+) Mc
The beam is made up of four boards, and is subjected to a moment of M=200 kip in, calculate the resultant force onthe top board C.
What is maximum moment induced in a simply supported beam of 20 foot span by a 2000 lb load at midspan? a. 125000 ft-lb b. 15000 ft-lb c. 30000 ft-lb d. 10000 ft-lb