Two wooden members shown which support a 4kip load, are joined by plywood splices fully glued on the surfaces in contact. The ultimate shearing stress in the glue is 360psi and the clearance between members is 1/4in. Determine the required length L of each splice if a factor of safety of 2.75 is to be achieved, 4kips 4in 4kips

Two wooden members shown which support a 4kip load, are joined by plywood splices fully glued on the surfaces in contact. The ultimate shearing stress in the glue is 360psi and the clearance between members is 1/4in. Determine the required length L of each splice if a factor of safety of 2.75 is to be achieved, 4kips 4in 4kips

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For a lap joint, determine the maximum safe load P which may be applied if the shearing stress in the rivets is limited to 60 MPa, the bearing stress in the plates to 110 MPa, and the average tensile stress in the plate to 140 MPa
A double-riveted double-strap butt joint is used to connect two plates; eachof 12 mm thickness, by means of 16 mm diameter rivets having a pitch of 48mm. The rivets and plates are made of steel. The permissible stresses in tension,shear and compression are 80, 60 and 120 N/mm2 respectively. Determine theefficiency of the joint.
The lap joint is fastened by 20 mm rivets placed alongside each other as shown along the length of the plate. Determine the safety of the lap joint to carry an axial load P=180 KN if the shearing stress in the rivets is limited to 60 MPa, the bearing stress in the plates to 110 MPa, and the average tensile stress in the plate is limited to 140 MPa. Plate width, W=140 mm, splice plate thickness, t=15 mm and main plate thickness, t = 40 mm. P = 180 KN
The two pieced of wood, 4 in. by 7.5 in. are glued together along the 35deg joint. Determine the maximum safe axial load P that can be applied if the shear stress in the glue limited to 200 psi and normal stress is limited to 380 psi
The eyelet (figure) is used to support a load of 3000 kgf. Determine its diameter d, and the required thickness h, so that the washer does not penetrate or shear the support. Knowing that the eyelet and washer must be made of 1020 steel, cold rolled, with a safety factor of 2.5, and the gap between the screw and the through hole must be 4mm, the steel used will be annealed and threadmachined, and the outer diameter of the washer will be 40mm.
For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the load is P = 64 kips.
The 1.4-kip load P is supported by two wooden members of uniform cross section that are joined by the simple glued scarf splice shown.Determine the normal and shearing stresses in the glued splice.
' Three piates are joined with a 12-mm diameter pin as shown beiow. Determine the maximum load p that can be transmitted by the joint if the maximum bearing stress between a plate and the pin must be limited to 650 MPa .
The rivet group connects two narrow lengths of plate, one of which carries a 15 kN load. If the ultimate shear strength t of a rivet is 350 N/mm² and its failure strength in compression stress is 600 N/mm², determine the minimum allowable values of rivet diameter d (mm) and plate thickness t (mm).
The axial stresses are 12 MPa C in the wood post B and 150 MPa T in the steel bar A as shown below. Pins at A, C, and D are smooth. Determine (a)The load P.(b)The minimum diameter for pin C if it is in single shear and the cross-shearing stress is limited to 70 MPa.(c)The minimum diameter for pin D if it is in double shear and the cross-shearing stress is limited to 70 MPa.
A flexible cable and rigid boom system is used to lift a load of 65kN at the end of Boom at point C. Points A and B are considered pinned in nature. The allowable shearing stress at all bolts are 250MPa and the allowable bearing stress at all bolts are 300MPa. Note that the initial position of boom is horizontal and segment A and B are vertical. Determine the horizontal reaction at A. 3. Determine the vertical reaction at A.
All pins are in double shear, each has a diameter of 13mm, and the average shear stress in each pin is not to exceed 65 MPa. Determine the maximum magnitude P of the loads that the beam can support