Two wrenches are used to tighten the pipe. The pipe ismade from a material having an allowable shear stress ofTallow = 80MPa. The pipe has an outer diameter of 25mm and inner diameter of 20 mmFigure 1Pof 1250 mmB<250 mm>PDetermine the allowable maximum force P that can be applied to each wrench.(Figure 1)Express your answer with the appropriate units.μAP = ValueSubmitUnitsMy Answers Give Up?Provide Feedback

Answered: Two wrenches are used to tighten the…

Two wrenches are used to tighten the pipe. The pipe is made from a material having an allowable shear stress of Tallow = 80MPa. The pipe has an outer diameter of 25 mm and inner diameter of 20 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: *?From the figure, determine R.L of Q from A al b h B a2 D S H1 H2 R. Lof Q = R.L of A +h+ H2O R.Lof…

Q: 1. You run a frequency analysis for a pretensioned beam structure (at one end the beam is…

A: An increase in the axial compression increases the frequency of the beam and vise versa ; The…

Q: If the Whole circle direction is (34°30') and the magnetic declination is (3°30')W the : magnetic…

A: Given data in question Whole circle bearing Magnetic Declination To find out Magnetic direction

Q: D/11 Oil, SG=0.83 3m 2m m Gate

Q: Figure 5 summarizes the loading on two footings. What will be the increase in the vertical stress…

A: Given data q = 30 KPa To Do :- What will be the increase in the vertical stress at point A which…

Q: A 3-m 150 mm CHB wall rests on a 600 mm thick concrete footing. The CHB wall weighs 3.3 kN/m² and…

A: Given:- The length of the wall = 3 m The thickness of the concrete footing is 600 mm The weight of…

Q: A constant-head test was conducted on a sample of soil 15 cm long and 60 cm² in cross-sectional…

Q: The strain components Ex, Ey, and Yxy are given for a point in a body subjected to plane strain.…

Q: Find the area of first prismoid if the areas of A1, A2 and A3 are 145.31, 257.43 and 59.67…

A: 1028.91 is the correct answer.

Q: AWT305 x 41 standard steel shape is used to support the loads shown. Assume w-42 kN/m, LAB-1.3 m,…

Q: SITUATION. A 5m high retaining wall with a vertical back face retains a homogeneous coarse- grained…

A: Given data in question Height Unit weight Cohesion Clay soil To find out Depth of tension crack

Q: What are ridge and contour canals? Write about their examples in Pakistan? Do you suggest that…

A: Ridge canal:- This type of canal is aligned along any non-manmade watershed or ridge line that is a…

Q: For the beam and loading shown, use discontinuity functions to compute: (a) the deflection VA of the…

A: Given data EI = 1550 KNm2

Q: Design the pipe that will connect two reservoirs for a water distribution system of a certain sitio.…

A: Head Loss - When water flow from source to its end point in a pipe it follows Energy Equation i.e…

Q: The latitude for the figure can be given as (0 = 50° 34') 0 245m 161.34m O 155.62 O 160.43m O 165m O…

A: Given data in question Length Angle To find out Latitude

Q: A 40 kg block is attached to the wall with a wire and is resting on the 50 kg and 30 kg blocks on an…

A: given mass block of 40kg resting on 50kg and 30kg blocks from force balance: N1 = 40gcos30 =…

Q: The cross-sectional dimensions of the beam shown in the figure are a = 4.2 in., b=4.9 in., d = 5.0…

A: Given data Mz = - 3.55 kip-ft For negative moment, tension is generated on top fiber of section…

Q: The latitude for the figure can be given as (0 = 50° 34¹) 0 245m 161.34m O 155.62 O 160.43m O 165m O…

A: 155.62 is the correct answer.

Q: 4) A simply supported beam supports the uniformly distributed load of intensity Wo. Determine the…

A: Given ;

Q: Design a welded plate girder for simply supported bridge deck bear with a clear span of 20 m,…

A: Given data:- Length of bridge deck, l=20 m Deal load, DL=18 kN/m Imposed load, IL=8 kN/m Two moving…

Q: SITUATION. At the exit of a toll gate with a single booth, vehicles arrive at random at an average…

Q: List all zero-force members of the truss. 1m 2m 2 m 2m 2m H F -6 m- K D I G E C M B L N e P R 1kN…

A: To Determine All the zero force members of the given Truss.

Q: A bar screen is used to treat 10 MGD of menicipal wastewater. The vertical bars are 1.27 cm wide and…

A: Answer We are given Q = 10 MGD bar width b = 1.27 cm bar depth d = 3.8 cm Minimum allowable spacing…

Q: An isolated Tbeam has flange of 2400 mm wide and 120 mm deep. The effective width and depth of web…

A: Given values: For isolated T beam, Flange: Width, bf= 2400 mm Depth, Df = 120 mm Web: Width, bw =…

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A: From figure :σx=4700psi=2800psiσy=-2700psi=-1400psiτxy=6700psi=4200psi

Q: A cantilever beam of length 1m carries a point load of 1900N at the free end. The cross-section of…

A: Given data:- length of cantilever beam, L=1 m Point load, P=1900 N Dimension of cross-section of…

Q: A constant-head test was conducted on a sample of soil 15 cm long and 60 cm² in cross-sectional…

A: Given data: for the constant head test sample of length, L = 15cm having soil cross sectional area,…

Q: Problem 2. This is a four-part problem. A +2.5% grade intersects with a –1.5% grade at station (735…

A: Note:- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: 9.4 What specific air-pollution-control devices are available for control of particulate emissions…

A: This question is from environmental engineering. It belongs to air pollution control chapter Here we…

Q: Calculate the closing error of the following traverse Line AB BC CD DE EA Length (m) 193.20 176.80…

Q: Find out the deflection angles from the following observations Lines AB BC Bearing N 42° 20' E N 30°…

A: Deflection angle=42°20'-30°00' =12°20' L

Q: The column is 480" long and is Ball and Socket supported on each end. The column is A36 steel with E…

A: Section C10×15.3 Properties: Ag= 4.48 in2Ix = 6.73 in4Iy = 2.27 in4x = 0.634 in The total moment of…

Q: 4) A simply supported beam supports the uniformly distributed load of intensity Wo. Determine the…

A: Let Ra and Rd be the reactions at A and D Supports Considering equations of equilibrium, Ra + Rd =…

Q: From the figure, determine R.L of Q from A? al B #2 D S R.Lof Q = R.L of A + h + H2 R.Lof Q = R.L of…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 60 MPa and…

A: Given Sx=60Mpa Sy=-215Mpa

Q: Line AB BC CD DA A clockwise traverse ABCDEA was surveyed Find the length and direction of line AD…

Q: 1 in. (1 in. = 2.54 cm). We also determine in the lab its weight and volume at various litions. The…

A: (a) Moisture content of green =223.1-143.5143.5×100%=wt. of water wt. of solid×100…

Q: A 14-ft-long simply supported timber beam carries a P = 6.0 -kip concentrated load at midspan as…

Q: What is the difference between inductive and deductive reasoning?

A: The process of reaching a logical conclusion after considering all the relevant facts is called…

Q: 1- A concrete slab with 180 mm thickness support dead load 5kN/m² include self- weight and service…

A: ->Thickness of one-way sections should be essentially L/20 for basically upheld chunks; L/24 for…

Q: 1. Using Rayleigh-Ritz method, determine the expressions for displacement and stress in a fixed bar…

A: The given figure is shown below:

Q: A beam has a width of 275 mm and an effective depth of 500 mm. f'c = 28 MPa. Fy = 414 MPa, Es =…

Q: In a fill section of a construction site, 1500 m3 of moist compacted soils is required. The design…

Q: A clockwise traverse ABCDEA was surveyed Find the length and direction of line AD Line AB BC CD DA…

A: To Determine Length and bearing of line AD.

Q: 2. Get the twist of section A: a) By the elastic equation, indicating the value and direction. b) By…

A: The given figure is shown below:

Q: SITUATION. Based on the figure shown a hallow steel pipe with external diameter Do of 200mm has a…

A: Given dataExternal diameter = 200 mmlength = 3 mE = 200 GPathickness t = 8 mmwe have to find P…

Q: If the reduced bearing of a line AB is N60°W and length is 100 m, then the latitude and departure…

Q: The truss is subjected to the loading shown. It is supported by a pin at A and a roller at L.…

Q: نقطتان (2) * If the formation level at zero chainage is 150 metres and there is rising gradient of 1…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sx - 60 MPa and Sy=…

Concept explainers

Test for Determination of Shear Strength

The term shear strength is often associated with the soil. Shear strength is defined as the resistance to the deformation of soil particles due to the continuous action of shear stress. In short, shear strength is the maximum shear stress that a soil can sustain.

Question

Two wrenches are used to tighten the pipe. The pipe is
made from a material having an allowable shear stress of
Tallow = 80MPa. The pipe has an outer diameter of 25
mm and inner diameter of 20 mm
Figure 1
P
of 1
250 mm
B
<
250 mm
>
P
Determine the allowable maximum force P that can be applied to each wrench.
(Figure 1)
Express your answer with the appropriate units.
μA
P = Value
Submit
Units
My Answers Give Up
?
Provide Feedback

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Test for determination of shear strength

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The screw clamp shown in the figure applies a P = 500 N pressing force to the wooden blocks between the jaws. In this case; a) Calculate the greatest tensile and compressive stresses occurring in the section a-a shown in the figure. b) Show the distribution of normal stresses across the section height. (draw) c) Since the clamp material has tensile strength (apull) safety = 50MPA and compression safe stress (opress) safety = 80MPA, what is the great compressive load (P) that can be applied without damaging the a-a section? %3D %3D (Please solve in detail and according to engineering rules.) Material mechanics Sectional view a-a - 20mm T. 183mm 40mm
Question 4. Three wires are used to suspend the plate shown. Aluminium wires are used at A and B with a diameter of 3 mm and a steel wire is used at C with a diameter of 2 mm. Knowing that the allowable stress for aluminium (E = 72 GPa) is 96 MPa and that the allowable stress for steel (E = 200 GPa) is 124 MPa, determine the maximum load P that may be applied. L L P B
SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the maximum force F that can be applied to the plates. The allowable axial stress of each plate is 150 Mpa. The allowable shear stress of each bolt is 50 MPa. The diameter of each bolt is 16 F F 150 mm 啡 F mm. 50 mm 340 mm
1. The bar ABCD consists of 3 cylindrical steel segments with different lengths and cross-sectional areas. Axial loads are applied as shown. Calculate the normal stress in each segment in psi unit. Indicate if T or C.Calculate the total axial deformation in Problem #1 if Es = 29 x 10 6 psi . Indicate if the bar elongates or contracts.
SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the maximum force F that can be applied to the plates. The allowable axial stress of each plate is 150 Mpa. The allowable shear stress of each bolt is 50 MPa. The diameter of each bolt is 16 F F 150 mm mm. 50 mm 340 mm
Q// A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm', determine the stress in each section. 4P Steel Bronze Aluminum P 609.6 mm 914.4 mm 762 mm
A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid brass shaft with an outside diameter of 0.51 in. and an allowable shear stress of 4500 psi. Segment (2) is a solid aluminum shaft with an outside diameter of 0.41 in. and an allowable shear stress of 6000 psi. Determine the magnitude of the largest torque TC that may be applied at C. Express your answer in lb-in rounded to the nearest tenths.
!! Show Complete & Detailed Solution w/ FBD !!The figure shows that when the rigid bar is in the horizontal position, the wires are unyielding. The bar rotates clockwise about the pin B through an angle of 2.1° when a force is applied at the handle. Determine the average normal strain developed in wires.a. AHb. CGc. DF
In figure shown below B 960 Imm 640 N 3 280 mm 960 N a. Determine the tension in segment AC b. Determine the tensibn in segment BC
1. For the riveted connection shown in the figure using elastic analysisa. Determine the safe value of P if the allowable shearing stress of 25mm rivets is 150MPab. Determine the maximum shearing stress that can be develop in the rivet for a given load ? = 52??c. Determine the minimum shearing stress that can be develop in the rivet for a given load ? = 52?N
You are an engineering intern at a manufacturer of mechanical tools, your senior engineer asked you to evaluate the stresses on a newly-design utility hook, shown in Figure.6, to confirm it's not exceeding its yield strength. The hook dimensions are (d, D¡, L) = (20, 75, 250) mm. The task can be completed by calculating the stresses at the inner and outer surfaces of section A – A when the load is F = 4 kN. L Figure.6: Utility hook
Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum tensile bending stress will occur at point C. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner C does not exceed 205 MPa. Answer: M- eTextbook and Media Save for Later Part 3 8.31E1 Answer: M-i The z-component of moment M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum compressive bending stress will occur at point A. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner A does not exceed 205 MPa. eTextbook and Media Save for Later Part 4 kN-m * Your answer is incorrect. kN-m Submit Answer Determine the maximum bending moment that can be applied to this cross…