Please provide a clear solution, a pv, and a ts diagram. e✔7.10 If 2 kg of steam at 18 bar and 288°Cundergo a constant pressure process until thequality becomes 50% (h₂ = 2220, V₂ =Sz0.075, S₂ = 5.18). Find W, AH, Q, AU, andAS: (a) if the process is nonflow, (b) if theprocess is steady flow with AK = 0. UseItem B 16(SI).1eiAns. (a) W = -220 kJ, Q = -1566 kJ,AS = -3.20 kJ/K.711

Answered: Image /qna-images/answer/cbbdbb7f-ae57-4a4c-8d59-f0b49492e598.jpg

undergo à constant pressure process until the quality becomes 50% (h₂ = 2220, V₂ = 0.075, S₂ = 5.18). Find W, AH, Q, AU, and AS: (a) if the process is nonflow, (b) if the. process is steady flow with AK = 0. Use Item B 16(SI). Ans. (a) W = -220 kJ, Q = -1566 kJ, AS = -3.20 kJ/K.

undergo à constant pressure process until the quality becomes 50% (h₂ = 2220, V₂ = 0.075, S₂ = 5.18). Find W, AH, Q, AU, and AS: (a) if the process is nonflow, (b) if the. process is steady flow with AK = 0. Use Item B 16(SI). Ans. (a) W = -220 kJ, Q = -1566 kJ, AS = -3.20 kJ/K.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a steam turbine system, suppose the value of ∆mH is constant (meaning, inlet and outlet conditions are maintained). From the energy balance equation, Qnet + Wnet = ∆mH + ∆KE + ∆PE or −0.1209 kW − 70 kW = ??̇? + 8.75 kW − 0.0068kW 1. What will happen to Wnet if there was no increase in kinetic energy, will the magnitude of Wnet increase or decrease? What should be the sign of potential energy so that Wnet will increase in magnitude?2. For a turbine system, what should happen to Qnet, ∆KE, and ∆PE to maximize the work done by the turbine? Which factor is the most significant?
Please indicate the given, assumption and illustration. A large tank contains air at 2.84 bar gauge pressure and 24°C temperature. The air flows from the tank to the atmosphere through an orifice. If the diameter at the orifice is 2 cm, find the maximum flow rate of air, in kg/sec. Take R = 287 J/kg·K, k = 1.4, and ambient pressure = 1 bar.
3.) Find the pressure ,specific volume ,internal energy ,enthalpy ,entropy of saturated water at 300 F . 4.)Find the temperature ,specific volume ,internal energy ,enthalpy ,entropy of saturated steam at a pressure of 1 inch Hg absolute.
1/Air at 8 bar, 100°C flows in a duct of 15 cm diameter at rate of 150 kg/min. It is then throttled by a valve unto 4 bar pressure. Determine the velocity of air after throttling and also show that enthalpy remains constant before and after throttling.
With a flow rate of 50 kmol/hour, air is compressed from P 1 = 1.2 bar pressure to P 2 = 6 bar pressure. The power required for this process is 98.8 kW. Temperature and speed data are given below. T1 = 300 K ,T 2 = 520 K ,v1 = 10 m/s, v2 = 3.5 m/s What is the heat rate transferred to the compressor (kJ/s)? Assume that air has Cp = (7/2)R and enthalpy is independent of pressure. (Gpt/Ai wrong ans not allowed)
A turbine is driven by a system that enters the turbine at the ff. conditions: 200 kg/h, 39 atm, 501 deg C, 49 m/s linear speed. The steam exits at a point 8 meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 290 m/s speed. 69000 W of shft work is delivered by the turbine while 100 kcal/h heat is lost. What is the value of (a) expansion work and (b) flow work? If the value is zero, explain why is it so.If it cannot be calculated, explain why.
A two stage compressor with first stage piston displacement of 94,390 cu.m/sec is driven by a motor. Motor output is 35 HP, suction temperature 22 degC, volumetric efficiency is 85%, mechanical efficiency is 95%, the intercooler pressure is 30 psi gage. Air temperature in and out of the intercooler are 105deg C and 44 degC, respectively. Final discharge pressure is 100 psi gage, while suctionis estimated to be 14.4 psi. Determine the compression efficiency.
Giver Argon at P1=140kn/m2, T1=10 C, V1=200. Liters that undergoes a polytropic compression to P2=700kPa, T2=180 C, M=39.984kg/mole, R=0.2081 kJ/kg K, cv=0.312kJ/kgK. Find Q.
A steam sample is removed from line where the pressure is 225 psia and passed through throttling calorimeter. The calorimeter thermometer reads 265 °F and 15 psia. Find the following in the line steam: (a) enthalpy, (b) quality, (c) entropy, and (d) temperature to the nearest whole degree.
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Why is expansion work 0 and why cannot the flow work be calculated?
Solve please, should 100% sure of ans. Air enters a well-insulated turbine operating at steady state with a negligible velocity at 4 MPa and 300 oC, It exits the turbine at 100 kPa pressure at 100 oC. The diameter of the exit pipe is 60 cm. The velocity at exit is 90 m/s. a. What is the volumetric flow are at the exit? Express your result in units of m3/s. b. What is the molar flow rate at the exit? Assume that at the exit conditions, air may be considered to behave like an ideal gas. Express your results in units of mols/s c. What is the mas flow rate? Express your result in units of kg/s.
A steam trap is a device to purge steam condensate from a system without venting uncondensed steam. In one of the crudest trap types, the condensate collects and raises a float attached to a drain plug. Whenthe float reaches a certain level, it “pulls the plug,” opening the drain valve and allowing the liquid to discharge. The float then drops down to its original position and the valve closes, preventing uncondensed steam from escaping.(a) Suppose saturated steam at 25 bar is used to heat 100 kg/min of an oil from 135°C to 185°C. Heat must be transferred to the oil at a rate of 1:00 x 10 4 kJ/min to accomplish this task. The steam condenses on the exterior of a bundle of tubes through which the oil is flowing. Condensate collectsin the bottom of the exchanger and exits through a steam trap set to discharge when 1200 g of liquid is collected. How often does the trap discharge?(b) Especially when periodic maintenance checks are not performed, steam traps often fail to close completely…