Use the exact values you enter in previous answer(s) to make later calculation(s). Consider the following figure. (Assume R, = 31.0 fA, R, = 19.0 n, and V= 18.0 V.). R 10.0 V 5.00 N R2 (a) Can the circuit shown above be reduced to a single resistor connected to the batteries? Explain. No they cannot due to their connections they must remain together in a parallel circuit Score: 1 out of 1 Comment: (b) Find the magnitude of the current and its direction in each resistor. X A X A X A R: 19.0 1 = 202893 = 342065 5.00 n 31.0 n = = .616333

Use the exact values you enter in previous answer(s) to make later calculation(s). Consider the following figure. (Assume R, = 31.0 fA, R, = 19.0 n, and V= 18.0 V.). R 10.0 V 5.00 N R2 (a) Can the circuit shown above be reduced to a single resistor connected to the batteries? Explain. No they cannot due to their connections they must remain together in a parallel circuit Score: 1 out of 1 Comment: (b) Find the magnitude of the current and its direction in each resistor. X A X A X A R: 19.0 1 = 202893 = 342065 5.00 n 31.0 n = = .616333

College Physics

10th Edition

ISBN:9781285737027

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter18: Direct-Current Circuits

Section: Chapter Questions

Problem 27P: (a) Can the circuit shown in Figure P18.27 be reduced to a single resistor connected to the...

See similar textbooks

Similar questions

A child's electronic toy is supplied by three 1.58-V alkaline cells having internal resistances of 0.0200 inseries with a 1.53-V carbon-zinc dry cell having a 0.100- internal resistance. The load resistance is 10.0 . (a) Draw a circuit diagram of the toy and itsbatteries, (b) What current flows? (c) How much power is supplied to the load? (d) What is the internal resistance of the dry cell if it goes bad, resulting in only 0.500 W being supplied to the load?
A 1,00-?O voltmeter is placed in parallel with a 75.0kresistor in a circuit, (a) Draw a circuit diagram of the connection, (b) What is the resistance of the combination? If the voltage across the combination is kept the same as it was across the 75.0-kresistor alone, what is the percent increase in current? (d) If the current through the combination is kept the same as it was through the 75.0-kresistor alone, what is the percentage decrease in voltage? (e) Are the changes found in parts (c) and (d) significant? Discuss.
A 20.00-V battery is used to supply current to a 10-k resistor. Assume the voltage drop across any wires used for connections is negligible, (a) What is the current through the resistor? (b) What is the power dissipated by the resistor? (c) What is the power input from the battery; assuming all the electrical power is dissipated by the resistor? (d) What happens to the energy dissipated by the resistor?
In Figure 21.41. does the graph indicate the time constant is shorter for discharging than for charging? Would you expect ionized gas to have low resistance? How would you adjust R to get a longer time between flashes? Would adjusting R affect the discharge time?
(a) A defibrillator sends a 6.00-A current through the chest of a patient by applying a 10,000-V potential as in the figure below. What is the resistance of the path? (b) The defibrillator paddles make contact with the patient through a conducting gel that greatly reduces the path resistance. Discuss the difficulties that would ensue if a larger voltage were used to produce the same current through the patient, but with the path having perhaps 50 times the resistance. (Hint: The current must be about the same, so a higher voltage would imply greater power. Use this equation for power: P=I2 RP = .)
The circuit shown in Figure P27.17 is connected for 2.00 min. (a) Determine the current in each branch of the circuit. (b) Find the energy delivered by each battery. (c) Find the energy delivered to each resistor. (d) Identify the type of energy storage transformation that occurs in the operation of the circuit. (e) Find the total amount of energy transformed into internal energy in the resistors.
Consider a circuit that consists of a real battery with an emf and an internal resistance of r connected to a variable resistor R. (a) In order for the terminal voltage of the battery to be equal to the emf of the battery, what should the resistance of the variable resistor be adjusted to? (b) In older to get the maximum current from the battery, what should the resistance variable resistor be adjusted to? (c) In order for the maximum power output of the battery to be reached, what should the resistance of the variable resistor be set to?
A typical cell phone consumes an average of about 1.00 W of electrical power and operates on 3.80 V. (a) What average current does the phone draw from its battery? (b) Calculate the energy stored in a fully charged battery if the phone requires charging after 5.00 hours of use.
Ralph has three resistors, R1, R2, and R3, connected in series. When connected to an ideal emf source E1, current I1 flows through the resistors. a. If the resistors are instead connected to a second source with E2=2E1, what is the new current through the resistors in terms of the first current? b. Show that, if each resistance is doubled and the resistors are connected in series to the second emf source, the current through the resistors is equal to I1.
The power dissipated in a resistor is given by P = V2/R, which means power decreases if resistance increases. Yet this power is also given by P = I2R, which means power increases if resistance increases. Explain why there is no contradiction here.
Two 1.50-V batterieswith their positive terminals in the same directionare inserted in series into a flashlight. One battery has an internal resistance of 0.255 , and the other has an internal resistance of 0.153 . When the switch is closed, the bulb carries a current of 600 mA. (a) What is the bulbs resistance? (b) What fraction of the chemical energy transformed appears as internal energy in the batteries?
Using your understanding of the nature of internal energy and temperature, explain why we might expect the resistance of a solid to increase if its temperature increases.