What is the component/material that is on the pencil that gives a high resistance? With the values given on the images, what are the corresponding color codes (indicate tolerance using a 4-band color code scheme)? If the first value is connected in series with the other value, what is the total resistance? If it’s parallel what is the total resistance?

What is the component/material that is on the pencil that gives a high resistance? With the values given on the images, what are the corresponding color codes (indicate tolerance using a 4-band color code scheme)? If the first value is connected in series with the other value, what is the total resistance? If it’s parallel what is the total resistance?

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter9: Current And Resistance

Section: Chapter Questions

Problem 46P: An electronic device designed to operate at any temperature in the range from 10.0C to 55.0C...

See similar textbooks

Similar questions

An experiment is conducted to measure the electrical resistivityof Nichrome in the form of wires with different lengthsand cross - sectional areas. For one set of measurements, astudent uses 30.0 - gauge wire, which has a cross - sectionalarea of 7.30 x 10-8 m2. The student measures the potentialdifference across the wire and the current in the wire with avoltmeter and an ammeter, respectively. For each of the measurementsgiven in the following table taken on wires of threedifferent lengths, calculate the resistance of the wires and thecorresponding value of the resistivity. What is the average value of the resistivity, and how does thisvalue compare with the value given in Table 17.1?
Do you think the resistor you measured are generally within tolerance? What evidence support your answer ?
Pacemakers designed for long-termuse commonly employ a lithium-iodine battery capable of supplying 0.42 A # h of charge. (a) How many coulombs of chargecan such a battery supply? (b) If the average current producedby the pacemaker is 5.6 mA, what is the expected lifetime of thedevice?
A certain flashlight is connected to a 6.0-Vemf battery and has an internal resistance of 0.100. What power does the 0.500 M load dissipate? If the internal resistance grows to 0.400 2, what is the new current, terminal voltage, and power dissipated by a 0.500 M load resistance?
For temperature-dependent ohmic resistors (at least the kind we're focusing on), the relationship between resistance & temperature is linear. With that in mind, compare the formula for temperature-dependent ohmic resistance to the equation for a line (y = mx + b) and determine the slope and the y-intercept for a graph of R vs. T. Your answers should be in terms of Ro, ?, & To. [NOTE: for Ro & To the subscript is a lowercase o] R = Ro[1 + ?(T − To)] slope = y-intercept =
Let's say you have a 20 cm long silicon wire, with a diameter of 4 cm. What current flows through this wire if a 1000 V potential difference is applied to the two ends? Please enter your answer in the unit of mA. You can use 2300 Ohm.m for the resistivity of silicon.
A high tension (HT) supply of, say, 6 kV must have a very large internal resistance. Why?
What is the resistance of a copper bus bar 9.15 meter long and 7.62 cm by 1.27 cm in cross section? Use 1.78 μΩ-cm specific resistance for copper.
A wire of length 1 km, has a conductance of 0.6 mho. What is theconductance of the same wire which is 3 km long?
Please help: Pacemakers designed for long-term use commonly employ a lithium-iodide battery capable of supplying 0.42 A•h of charge (A) How many coulombs of charge can such a battery supply? Express your answer using two significant figures (B) If the average current produced by the pacemaker is 5.6 micro Amps, what is the expected lifetime of the device? Express answer using two significant figures
Calculate the conduction velocity if the electrodes are 12cm and there are 0.3sec between the time of stimulation and the peak of the CAP.
An unknown wire in a circuit has a circular cross-section with diameter 3.8 mm. It carries a current of 4.2 mA. If you assume the drift velocity in this wire is 1 × 10-2 cm/s, what is the density of charge carriers per cubic centimeter? If the conductivity in this wire is 3.5 × 106 Ω-1 m-1, what is the average time between collisions, in nanoseconds? J=37.03 n=???? τ =????