Use the following information to answer the next two questions The current I, in amperes, flowing through an alternating circuit, at a time of t seconds can be modeled by the equation I = 30 sin (bt). 1 seconds. 25 The period of the function is An electrician is asked to determine the value of b in the equation, and use the equation to determine the current at a time of 12 seconds. b Value Current at 12 sec 29.9 amperes 25 В. 50t 29.9 amperes С. 0.25 amperes 25 D. 50r 0.25 amperes The row of the table below that shows the correct information is A.

Use the following information to answer the next two questions The current I, in amperes, flowing through an alternating circuit, at a time of t seconds can be modeled by the equation I = 30 sin (bt). 1 seconds. 25 The period of the function is An electrician is asked to determine the value of b in the equation, and use the equation to determine the current at a time of 12 seconds. b Value Current at 12 sec 29.9 amperes 25 В. 50t 29.9 amperes С. 0.25 amperes 25 D. 50r 0.25 amperes The row of the table below that shows the correct information is A.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

Problem 15. A source of e.m.f. of 15V supplies a current of 2A for six minutes. How much energy is provided in this time?
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
Q13) For the circuit shown in the figure. a) Calculate the ripple factor. b) Sketch and label the output voltage waveform . T1 D1 V1 120Vpk 60HZ 0° 10:1 C1 1G4B42 R1 :100μΕ 1.5kQ 014) Sketch th I the touol
An alternating current varying sinusoidally with a frequency of 50 Hz has anrms value of 20 A.a) Determine the instantaneous value at 0.0025 seconds.b) Determine the instantaneous value, 0.0125 seconds after passingthrough a positive maximum value.c) At what time, measured from a positive maximum value, will theinstantaneous current be 14.14 A?
Alternating voltage and current differ from direct voltage and current because alternating voltage and current a.)never change. b.)change polarity. c.)maintain a constant polarity. d.)are not real electricity The period (T) of a waveform is a.)unrelated to the frequency. b.) the reciprocal of the frequency. c.)equal to the frequency. d.)the reciprocal of the cycle
1-Choose the correct statement for pure resistor connected across single phase AC supply. a. Current and Voltage are in phase b. Current leads the supply voltage by 90° c. None of these d. Current lags the supply voltage by 90° 2-Identify the current through the inductor in a RL transient circuit connected across DC voltage, when the switch is kept open. a. 0 b. Infinity c. V/R d. 1
14. A 50 - cycle current has a maximum value of 7.5 amp. What will be the instantaneous value of current 0.0035 sec after the wave passes through the zero in a positive direction. a. 0.1439 A b. 1.2552 A c. 6.6825 A d. 9.4506 A
The ripple factor for pure dc is Answer:
An alternating current of frequency 60HZ has a maximum value of 12A. Write down the equation for its instantaneous value. Reckoning time from the instant the current is zero and is becoming positive, find (a) instantaneous value of 1/360 sec (b) the time taken to reach 9A for the first time
A curve is drawm in descending order of load with time. Al1
An alternating current varying sinusoidally with a freq. of 50 c/s. has a r.m.s. value of 35 A. Write down the equation for the instantaneous value and find this value at (i) 0.0035 sec. (ii) 0.0135 sec. after passing through a positive max. value.
8. Liquids with solid impurities a) Have higher dielectric strength b) Of large size have higher dielectric strength c) Have lower dielectric strength as compared to pure liquids d) None of the above 9. Peak to peak ripple is defined as a) the difference between average de voltage and peak value b) the difference between maximum and minimum de voltage c) the difference between maximum ac and average de voltages d) the difference between ac (rms) and average de voltages 10. In a Cockroft-Walton circuit, input voltage 100 kV load current 25 mA, supply frequency 100 Hz, each capacitor 10 nF. The optimum no. of stages for maximum output voltage is a) 1 b) 2 c) 10 d) 35