Using the D.C. shunt motor no-load and full-load information given in thefollowing table, determine the motor speed regulation. Give your answer inpercent.Motor DataNo LoadFull Load9393Supply Voltage Vs (V)Supply Current Is (A)1.076210.4839Field Circuit Resistance Rf (S)177177Armature Circuit Resistance Ra (2)0.960.96Rotational Speed (r/min)1989...Answer:0%

Using the D.C. shunt motor no-load and full-load information given in the following table, determine the motor speed regulation. Give your answer in percent. Motor Data No Load Full Load Supply Voltage Vs (V) Supply Current Is (A) Field Circuit Resistance Rf (Q) 93 93 1.0762 10.4839 177 177 Armature Circuit Resistance Ra (2) 0.96 0.96 Rotational Speed (r/min) 1989 Answer: 0%

Using the D.C. shunt motor no-load and full-load information given in the following table, determine the motor speed regulation. Give your answer in percent. Motor Data No Load Full Load Supply Voltage Vs (V) Supply Current Is (A) Field Circuit Resistance Rf (Q) 93 93 1.0762 10.4839 177 177 Armature Circuit Resistance Ra (2) 0.96 0.96 Rotational Speed (r/min) 1989 Answer: 0%

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.24P: For Problem 3.18, the motor operates at full load, at 0.8 power factor leading, and at a terminal...

See similar textbooks

Similar questions

A gas turbine, 2-pole, 3? synchronous generator rated at 200 MW is connected to the grid (presumed to be an infinite bus). The electrical operating frequency of the grid is 60 Hz, and the slope of the frequency-power curve for the generator is 15 MW/Hz. a. If the no-load setpoint for the generator is set to 63.5 Hz, how much active power will the generator provide to the grid? b. Neglecting system losses, what is the torque provided by the gas turbine? c. What would happen if the no-load setpoint for the generator is set to 59 Hz?
The following information is given for a 300 kw, 600 V long shunt compound generator. Shunt field resistance = 75 Ω, armature resistance including brush resistance = 0.03 Ω, commutating field winding resistance = 0.011 Ω, series field resistance = 0.012 Ω, diverter resistance = 0.036 Ω. When the machine is delivering full load, calculate the voltage, power generated by the armature and efficiency.
For Problem 3.18, the motor operates at full load, at 0.8 power factor leading, and at a terminal voltage of 10.45 kV. Determine (a) the voltage at bus 1, which is the generator bus, and (b) the generator and motor internal EMFs.
Using the 2 different 'single phase equivalent circuits' given below, the desired equations will be deducted. Equations separately for asynchronous motor powered by voltage source will be removed and the spaces given below will be written. You can also do your inference work. show it and deliver it. V1 and I1 are the RMS value of the AC phase voltage and current. All formulas (3 phase motor) will be written as a function of motor parameters and slip.
Two D.C shunt generations running in parallel supply s total load current of125 A. The shunt field and armature resistances of each machine are 50 ohms and0.4 ohm respectively. The e.m.f.s. of the two generators at no load are 260 Vand 250 V respectively. Determine:(i) Current supplied by each generator: and(ii) The bus bar voltage.
A separately excited generator has no-load voltage of 125V. A certain load rated at 1200W, 120V is then connected at the terminal. Calculate the series resistance needed to connect to the armature circuit in order for the load to operate at rated condition if the armature resistance is 0.0692Ω.
For 3-phase,50 Hz, SCIM, rotor leakage reactance at standstill is twice of it's resistance.The frequency of the supply at which maximum torque is obtained at starting is ?
The armature, series field and shunt field resistances of 125 kW, 250 V long shunt cummulative compound DC generator are 0.025 ohms, 0.01 ohms and 30 ohms respectively. If stray power loss at rated load is 5 kW, determine the power in the armature field
Draw and explain the operation of H-type with 4-switches per phase drivecircuit and the drive circuit for bifilar winding for stepper motor. In whichtypes of stepper motors these circuits are used?
the armature series field and shunt field resistance of a 125 kw, 250V long shunt cumulative compound DC generator are 0.025ohms, 0.01ohms and 30 ohms, respectively. If the stray power stray loss at rated load is 25 kW, determine the power in the shunt field. Assume a astray load loss of 1% of the load power output (note: Input power generator is equal to the motor brake horsepower, Pin=Pl+Plosses) Choices A. 2034.5 W B.2082.5 W C. 2065.5 W D. 2053.5 W
A shunt generator supplies a 31kW load at 230V through cables of resistance, R = 122mΩ. If the field winding resistance, Rf =50Ω and the armature resistance, Ra =51mΩ. Determine the following below: The terminal voltage is, Answer and unit for part 1 The e.m.f. generated in the armature is,
Give the definition of percentage speed regulation.