Using this diagram: Given that This circuit runs on the flashbulb of a camera. Circuit is powered by 4 AA batteries each in series that are 1.5 V. The capacitor is C=50 mF when the switch makes contact on the left that is charged through the resistor that is. R1-10 ohm Switch in contact on the right, the capacitor discharges through the flashbulb with a A resistance of R2 = 1m2 that produces light. • What would be the average power of the light, during the time period of the flash. (please give answer in 2 significant digits) . What's the time duration in (us) of the the flash lasts after the capacitor is at a charge of 90 percent of total energy. When the capacitor is discharged through the bulb and the switch is switched to the right. Further knowing, that the light the bulb gives off has a potential across that is more than 1V) (2 sig figs )

Using this diagram: Given that This circuit runs on the flashbulb of a camera. Circuit is powered by 4 AA batteries each in series that are 1.5 V. The capacitor is C=50 mF when the switch makes contact on the left that is charged through the resistor that is. R1-10 ohm Switch in contact on the right, the capacitor discharges through the flashbulb with a A resistance of R2 = 1m2 that produces light. • What would be the average power of the light, during the time period of the flash. (please give answer in 2 significant digits) . What's the time duration in (us) of the the flash lasts after the capacitor is at a charge of 90 percent of total energy. When the capacitor is discharged through the bulb and the switch is switched to the right. Further knowing, that the light the bulb gives off has a potential across that is more than 1V) (2 sig figs )

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter19: Capacitors

Section: Chapter Questions

Problem 2PA: You are an electrician working in an industrial plant. You discover that the problem with a certain...

See similar textbooks

Similar questions

You are a journeyman electrician working in an industrial plant. Your task is to connect an inductor to a 480-V, 60-Hz line. To determine the proper conductor and fuse size for this installation, you need to know the amount of current the inductor will draw from the line. The nameplate on the inductor indicates that it has an inductance of 0.1 H. An ohmmeter reveals that it has a wire resistance of 10 . How much current should this inductor draw when connected to the line?
You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
An AC circuit contains a 24 resistor, a 15.9-mH inductor, and a 13.3F capacitor connected in parallel. The circuit is connected to a 240-V, 400-Hz power supply. Find the following values. XL=XC=IR=AIL=AIC=AP=WVARsL=VARsC=IT=AVA=PF=%=
Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
The current in the circuit is known to bei=B1e−2000tcos1500t+B2e−2000tsin1500t, t≥0.The capacitor has a value of 80 nF; the initial value of the current is 7.5mA; and the initial voltage on the capacitor is –30 V. Find the values ofR, L, B1, and B2
A resistor of R = 50Ω resistance is in series with a capacitor of C = 150μF. At t= 0, it is suddenly connected to a source of dc voltage of 25V. Determine the current in the circuit at any time t. Determine the current and the voltages across each element at t = 2τ.
An alternating current bridge is arranged as follows: The arm BC and DA consists of non-inductive resistance of 800 Ω each. A balance is obtained when resistances of the arms DE and CD of non-inductive variable resistances of 200 Ω, 1k Ω respectively. The arm EC of a capacitor of 1 µF capacitance. The alternating current source is connected to A and C and the telephone receiver to B and E. Calculate the resistance and inductance of arm AB. Also find Q factor, when supply frequency is 1500Hz.
What is VL,max(closed) and VL,max(open), the magnitude of the maximum voltage across the inductor during the time when the switch is closed? A circuit is constructed with four resistors, one inductor, one battery and a switch as shown. The values for the resistors are: R1 = R2 = 46 Ω, R3 = 92 Ω and R4 = 113 Ω. The inductance is L = 296 mH and the battery voltage is V = 12 V. The positive terminal of the battery is indicated with a + sign.
The circuit in the figure below has been connected for a long time. Let R1 = 7.80 Ω and R2 = 4.20 Ω.(a) What is the potential difference across the capacitor? which is 6.03 (b) If the battery is disconnected from the circuit, over what time interval does the capacitor discharge to one-half its initial voltage? in eed b
For the capacitor network shown In the figure below, C1-C2-D15 µF, C3=C4=10pF, C5=C6%35µF and the applied potential is Vab 30 V. Calculate the charge on the capacitor C4=10 pF. Give your answer in microcoulombs.
A series RL circuit consisting of a single resistor a single inductor is being supplied by a 20 volt battery. The circuit is currently open and has a initial current of 0 A. The resistor has a resistance value of 100 ahms. If the current flowing through the circuit 1.5 sec after closing the circuit is 0.15 A, find the value of inductance