v = 60 sin(wt + 30°) i = 15 sin(wt + 60°) Given the above expressions for voltage and current, find: i. Peak voltage i. RMS voltage ii. Peak current iv. RMS current V. Average Power Loss vi. Power Factor Is power factor leading or lagging? vii. Write voltage as a polar form. Write current in polar form. Write impedance (Z) in polar form. vii. ix. X.

v = 60 sin(wt + 30°) i = 15 sin(wt + 60°) Given the above expressions for voltage and current, find: i. Peak voltage i. RMS voltage ii. Peak current iv. RMS current V. Average Power Loss vi. Power Factor Is power factor leading or lagging? vii. Write voltage as a polar form. Write current in polar form. Write impedance (Z) in polar form. vii. ix. X.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter23: Resistive-inductive-capacitive Series Circuits

Section: Chapter Questions

Problem 7PP: Is the power factor in Question 6 a leading or lagging power factor? Explain your answer.

See similar textbooks

Similar questions

Given a sinusoidal voltage source in series with R,L, and C. The sinusoidal frequency is 600 Hz. R=2 Ohms, L=5 milliHenry, C=200 microFarad, V=70sin(wt) volts. Determine the watts and VARs for the capacitor, resistor, inductor, and source. Also find power factor. Given R1=9 Ohms, R2=1 Ohms, L= 3 milliHenries, and a sinusoidal voltage source of 5 volts amplitude and 60 Hz freqency all in series. Determine the voltage across R1: magnitude (volts), frequency (Hz), and phase (degrees).
If a current 5.0 A lags the applied voltage 230 V by an angle ϕ, it can be resolved into two components, OA in phase with the voltage and OB lagging by 90°. If the phasor diagram in to a circuit possessing resistance and inductance in series, OA and OB must not be labelled and respectively. It has become the practice to say that the power factor is laggingwhen the current lags the supply voltage, and leading when the current leads the supply voltage. This means that the supply voltage is regarded as the reference quantity. (a) A 30 μ F capacitor is connected across the applied voltage, 50 Hz supply. Calculate the reactance of 30 μ F capacitor connected across applied voltage (b) the reactance of the capacitor; (c) the current.
Understand ac power concepts, their relationships to one another, and how to calculate them in a circuitA load consisting of a 1.35 kΩ resistor in parallel with a 405 mH inductor is connected across the terminals of a sinusoidal voltage source vg, where vg = 90 cos 2500t V. Find 1. a) the average power delivered to the load,2. b) the reactive power for the load,3. c) the apparent power for the load, and4. d) the power factor of the load.
A transmission line with impedance of 0.085 + j 0.32 Ω is used to deliver power to a load. The load is inductive and the load voltage is 200∠0° Vrms at 60Hz. If the load operates at 20 kVA with a power factor of 0.75 determine the real and quadrature power losses in both the load and the line and the source voltage phasor.
Two alternating voltages are given by v1 = 15sinωt volts and v2 = 25 sin (ωt – π/6) volts. Plot both functions on the same axes and hence determine a sinusoidal expression for the resultant vr = v1 + v2. Check your answer using an analytical method. Your manager has asked you to analyse the variation in in results between the two methods
1. A motor load consists of a resistance of 6 Ohms in series with an inductance of 12 mH. Assume 120Vac, 60 Hz supply. a. What is the complex impedance of the load? b. What is the ac current through this load? c. What is theta, the angle between voltage and current through this load? d. What is the power factor? e. What capacitance should be added in parallel with this load to correct the power factor to 1? f. What is the current from the supply when the power factor is corrected?
For the circuit shown , what value of ZL results in maximum average power transfer to ZL? What is the maximum power in milliwatts?
1) Two alternating voltages are given by: v1 = 120 sin (ωt) volts and v2 =200 sin (ωt −π/4) volts. Obtain sinusoidal expressions for v1 −v2 (a) by plotting waveforms, and (b) by resolution of phasors.
An industrial installation has a power factor of 0.85 in backward. The demand is 150 KVA, and the operating voltage is 4800 V at 60 Hz. What should be done to bring the power factor to 0.95 in lagging? Indicate what you would connect and with what three-phase power. If the connection of the element to be added is in delta, indicate its reactance and the value of its capacitance or inductance. capacitance or inductance.
The impedance ZL in the circuit is adjusted for maximum average power transfer to ZL. The internal impedance of the sinusoidal voltage source is 4+j7 Ω. 1. a) What is the maximum average power delivered to ZL?2. b) What percentage of the average power delivered to the lineartransformer is delivered to ZL?
Between the terminals a and b in the figure, there is a load formed by connecting the resistor R0 and inductance L0 in series. The amplitude of the voltage Vs (t) is √2 150 volt phase angle Qs = 0 degree period T = 200π microseconds. Since R = 300ohm and C = 1 microfarad A) If the load phase angle QL = 30 degrees, find the values of R0 and L0 that enable the load to draw the maximum average power from the circuit. =? B) Calculate the average power on the load. =?
Is the power factor in Question 6 a leading or lagging power factor? Explain your answer.