RLine jXLine L1 L2 L3 Vz(rms) Three loads are supplied through a line in the figure. Find the magnitude of the impedance that is equivalent to the three parallel loads for the parameters given below L1: Absorbs an average power of 9kW at a unity power factor. L2: Absorbs an apparent power of 16 kVA at a lagging power factor of 0.95. L3 : Absorbs an average power of 9 kW and delivers 6 kvars. RLine = 0.1 XLine = 0.2 VL = 20020°V (rms) Lütfen birini seçin: a.2.9875 b.4.56 c.6.125 d.3.56 e 5 4075

RLine jXLine L1 L2 L3 Vz(rms) Three loads are supplied through a line in the figure. Find the magnitude of the impedance that is equivalent to the three parallel loads for the parameters given below L1: Absorbs an average power of 9kW at a unity power factor. L2: Absorbs an apparent power of 16 kVA at a lagging power factor of 0.95. L3 : Absorbs an average power of 9 kW and delivers 6 kvars. RLine = 0.1 XLine = 0.2 VL = 20020°V (rms) Lütfen birini seçin: a.2.9875 b.4.56 c.6.125 d.3.56 e 5 4075

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.12P: The voltage v(t)=359.3cos(t)volts is applied to a load consisting of a 10 resistor in parallel with...

See similar textbooks

Similar questions

Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
Under balanced operating conditions, consider the 3-phase complex power delivered by the 3-phase source to the 3-phase load. Match the following expressions, those on the left to those on the right. 0) Real power, Py (ii) Reactive power, Qu (ii) Total apparent power Sy (iv) Complex power, Sy (a) (V3 VLL. IL)VA (b) (V3 Vu sng) var (e) (V3 VLL. IL cos ø) W (d) Py +Qy Note that VLL is the rms line-to-line voltage, IL is the ms line current, and o is the power-factor angle.
Suppose the circuit shown represents a residential distribution circuit in which the impedances of the service conductors are negligible and Vg1=Vg2=120 0° V (rms). The three loads in the circuit are L1 (a new refrigerator, a coffee maker, and a microwave oven); L2 (2 incandescent lamps, a humidifier, and a ceiling fan); and L3 (a clothes washer and a clothes dryer). Assume that all of these appliances are in operation at the same time. The service conductors are protected with 20 A circuit breakers. Will the service to this residence beinterrupted? Why or why not?
A load impedance, Zo = 10 + j 3 ohm, is connected to a source with line resistance equal to 3 ohm, as shown in the figure. Determine the average powers delivered to the load and absorbed by the line. The average powers delivered to the load and absorbed by the line are ________ and ____________ , respectively.
Two balanced loads are connected to a 240-kV rms 50-Hz line. Load 1 draws 30 kW at a power factor of 0.6 lagging, while load 2 draws 45 kVAr at a power factor of 0.8 lagging. Assuming the RYB sequence, determine: (a) the complex, real, and reactive powers absorbed by the combined load, (b) the line currents, and (c) the kVAr rating of the three capacitors ∆-connected in parallel with the load that will raise the power factor to 0.9 lagging and the capacitance of each capacitor. Verify the results by creating a MATLAB Simulink model and program. Obtain the plots for the currents and voltages
Find the following: the power drawn by the 100ohm variable resistor If the variable resistor is set to 200-ohms, instead of 100-ohms, What is the power drawn by the 200-ohms resistor? total current of the system Is the circuit inductive, capacitive, or neither (resistive)? NOTE: Polar form for Voltage & Current. Rectangular form for Impedance
Visible power of Z1 = |S1| = 16 kVA and at 0.8 back power factor; Visible power of Z2 = |S2| = 25 kVA and operates at unit power factor; Loads ZW = 5 + j26ohm/conductor is connected to the source by transmission line; VL = 3.8 kV Find the visible power of source,power factor and rms of source
1. a) Find the average power dissipated in the line shown.2. b) Find the capacitive reactance that when connected in parallelwith the load will make the load look purely resistive.3. c) What is the equivalent impedance of the load in (b)?4. d) Find the average power dissipated in the line when the capacitivereactance is connected across the load.5. e) Express the power loss in (d) as a percentage of the power lossfound in (a).
In the case of reactive power compensation in a low voltage distribution network and increasing the power factor to cosQ2 = 0.92 as a result of compensation while cosQ1 = 0.75, which of the following expresses the change in apparent power transmitted from the line a) increase by 22.66% b) decrease by 22.66% c) increase by 18.47% d) increase by 15.00% e) decrease by 18.47%
Calculate ZL for maximum average power transfer in the circuit, and find the maximum average power delivered to the load. The given answer is ZL=2-j2 Ω, PL=45 W
1. Solve for the equivalent impedance and admittance seen at the source. Solve for is(t). 2. A load Z draws 12 kVA at a power factor of 0.856 lagging from a 120-Vrms sinusoidal source. Calculate: (a) the average and reactive powers delivered to the load, and (b) the peak current.
Between the terminals a and b in the figure, there is a load formed by connecting the resistor R0 and inductance L0 in series. The amplitude of the voltage Vs (t) is √2 150 volt phase angle Qs = 0 degree period T = 200π microseconds. Since R = 300ohm and C = 1 microfarad A) If the load phase angle QL = 30 degrees, find the values of R0 and L0 that enable the load to draw the maximum average power from the circuit. =? B) Calculate the average power on the load. =?