V, VZ sin ot 1. Refer to Figure 1. Assume all diodes are ideal, v,= where V, = 240 volt, w = 2nf, f=50Hz and t = time in second (s). Given the magnitude of ripple voltage, Vr(p-p) = 6V. a. Describe clearly the function of Block A, Block B and Block C b. Find the peak value of v, v; and v, c. Draw and completely label the waveforms of v, v½ and v3 d. Calculate the average value of v, e. What is the DC value of v,? D2 1002 1000 10 :1 Block A Block B Block C

V, VZ sin ot 1. Refer to Figure 1. Assume all diodes are ideal, v,= where V, = 240 volt, w = 2nf, f=50Hz and t = time in second (s). Given the magnitude of ripple voltage, Vr(p-p) = 6V. a. Describe clearly the function of Block A, Block B and Block C b. Find the peak value of v, v; and v, c. Draw and completely label the waveforms of v, v½ and v3 d. Calculate the average value of v, e. What is the DC value of v,? D2 1002 1000 10 :1 Block A Block B Block C

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where R1 and R2 are the resistances at temperatures T1 and T2, respectively, and is known as the temperature coefficient of resistance. If a copper wire has a resistance of 55 at 20C, find the maximum permissible operating temperature of the wire if its resistance is to increase by at most 20. Take the temperature coefficient at 20C to be =0.00382.
What is CEMF?
For the following circuit; a)- Diodes' conduction-cut status ("On" or "Off") determine mathematically.? (For diodes voltage drop model will be used. For each diode Vd = 0.7 V). b)- Currents passing through all branches of the circuit calculate? c)- 10 kΩ resistor on the right of the circuit Calculate the power spent on it.
b. Calculate the following about the circuit in the figure (If silicon diodes are employed in the rectification);i. the peak value of the output voltage considering the drop across each diode, Vpk.ii. the average voltage, Vdc. iii. The current through the load resistor, IL.iv. The current diode, Id.v. The frequency of the output signal, Fout.vi. Calculate the efficiency of the full wave rectifier expressed in percentage. vii. Sketch a graph of the input and output voltage against time.
Q2 (b) Multiple diodes circuit is given in Figure (i) Identify the condition for Si and Ge diodes. (ii) Determine the current flowing into Si and Ge diodes. (iii) Calculate the output voltage, Vo
For the given circuit, assume the diode D1 and D2 are the ideal diodes. The average value of the voltage Vab (in volts) across the terminal A and B is _________. Please Show Complete Solution and explanation.
Compare the results of static or dc resistance of the diodes obtained from different values of reverse voltages. Please explain.
accepting that D1 and D2 diodes have the same properties in the circuit given in the figurea) output voltage, b) current flowing through the resistor,c) current flowing from diodes calculate.
1- In your own words, describe the classification of materials according to conductivity, with examples of each type. 2- Plot the V I characteristics graph of Zener diode, label all values.
Answer the following questions according to the above. Remember Kirchhoff's laws when making your calculations in this question. a) According to the given graph, how many volts is the voltage value on it when this Zener diode is on a flat supply? b) According to the given graph, how many volts is the voltage value on this Zener Diode when it is on reverse supply? c) Calculate how many values V?−?? are when the zener current is 0 mA. D) Calculate how much the value of ??−?? is when the zener current is at its maximum value.
How are diodes tested for functionality? Write the necessary devices/materials needed to do the test and discuss thoroughly the procedure.