A full-wave bridge rectifier with a 314 V peak sinusoidal input has a load resistor of 10.61. If germanium diodes are employed, what is the DC voltage available at the load?2. Determine the required PIV rating of each diode.

Full wave bridge Rectifier peak voltage 314V load resistance 10.6k ohm 1. Average voltage 2. PIV?

A full-wave bridge rectifier with a 314 V peak sinusoidal input has a load resistor of 10.6 KO 1. If germanium diodes are employed, what is the DC voltage available at the load? 2. Determine the required PIV rating of each diode.

A full-wave bridge rectifier with a 314 V peak sinusoidal input has a load resistor of 10.6 KO 1. If germanium diodes are employed, what is the DC voltage available at the load? 2. Determine the required PIV rating of each diode.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Related questions

Q: c.1 Determine the ripple factor for the filtered bridge rectifier with a load as indicated in the…

Q: Q1):- A single-phase diode bridge rectifier is supplied at 120V. Determine the mean and r.m.s load…

Q: The single-phase half wave rectifier has R-L load with R= 5N nd L= 6.5mH. The input voltage V,=220V…

A: Given R-L load with R=5ohms and L=6.5mH. The input voltage Vs = 220 V at 50 Hz

Q: In a full wave rectifier circuit involving double diodes, a sinusoidal input signal of the following…

A: A full-wave rectifier is a circuit that converts the alternating voltage into direct voltage.

Q: B. Draw the circuit diagram of a clipper that will produce an output waveform below. From the output…

A: In this question , we will find two level clipping...

Q: Dy a.1 Determine the peak and dc output voltage for the bridge rectifier. a.2 Assuming the practical…

Q: An ac supply of 220 V is applied to a half-wave rectifier circuit through transformer with a turns…

Q: When the rms output voltage of a full-wave bridge rectifier is 31.8 V, the peak inverse voltage…

Q: For a bridge rectifier Assuming the diodes to be ideal, determine (a) d.c. output voltage, (b) peak…

A: Bridge Rectifier is a single phase full wave rectifier that converts ac signal to dc signal. where…

Q: Question 1 In the single-phase diode rectifier circuit shown in Figure 1 and a constant de load…

Q: Q.2) A three-phase half-wave diode rectifier is fed from an ideal three-phase supply of value 380 V…

A: We find the average output current from the given average diode current to find load resistance and…

Q: A 3 phase half wave controlled rectifier has a 3 phase line to line supply voltage of 430V rms at 50…

Q: 29.A simple half-wave rectifier consists of a diode and load. If the internal resistance of the…

Q: Q3) A full-wave bridge rectifier with a 220 V ms sinusoidal input has a load resistor of 6.2 KO 1.…

A: The solution can be achieved as follows.

Q: 2. Full Wave Bridge Rectifier a. Determine V. and the required PIV rating of each diode for the…

A: We need to find out output for full wave rectifier

Q: Q3 b) Fill in the blank 1- The maximum number of electrons that exist in shell 6 is . 2- The average…

Q: Q3):- A three-phase half wave rectifier has a supply of 150V/phase. Determine the mean load voltage…

A: Given a three phase half wave rectifier Vsupply = 150V/phase Load current iL = 25A Diode has voltage…

Q: A half-wave rectifier use diode having Internal resistance of 20ohm and load resistance of 1kohm. If…

Q: A load is connected in the Full Bridge rectifier circuit (Four Diodes). Used transformer primary…

A: According to the question, for a bridge rectifier, we need to calculate a) How many % of conduction…

Q: b. Calculate the following about the circuit in Figure 2.1 (If silicon diodes are employed in the…

Q: input voltage 320V ,conversion rate 23:3 at the output of the full wave rectifier circuit 2000 ohm…

A: Since the conversion rate of the transformer is given to be 23:3.The voltage on the secondary side…

Q: (a): Determine the ripple factor for the filtered bridge rectifier with a load as indicated in the…

A: According to question: a) The ripple factor for the filtered bridge rectifier is calculated as…

Q: 1. Build the following circuit. Use the function generator to obtain the specified AC input voltage.…

Q: A load is connected in the Full Bridge rectifier circuit (Four Diodes).

Q: Q.5) the output power dissipation in the single-phase half-wave diode rectifier with R load of 102…

Q: The figure shows a half-wave rectifier circuit with input voltage V(t) = 10 sin (100 t) volts.…

Q: 24. An ac voltage source of V max = 120 V is rectified using a half-wave rectifier circuit, using…

A: It is given that: Vmax=120 V

Q: 01) A full-wave rectifier uses two diodes. The transformer r.m.s. secondary voltage from the center…

A: As per guidelines given, we can provide the solution of first three subpart in multi part question.…

Q: Calculate the currents I1, 12 and 13 using the modified diode model (non-ideal, VD = 0.7V) for the…

A: The solution can be achieved as follows.

Q: rectification); i. the peak value of the output voltage considering the drop across each diode, Vpk.…

Q: 2. Full Wave Bridge Rectifier a. Determine V, and the required PIV rating of each diode for the…

A: We need to analyse the given full wave rectifier circuit .

Q: In a single phase full wave controlled rectifier connected to Inductive load (with freewheeling…

Q: The single phase diode rectifier has a purely resistive load of R , Determine 1. The efficiency 2.…

Q: accepting that D1 and D2 diodes have the same properties in the circuit given in the figure a)…

Q: Vp = Vs 5 = 1 D2 Vin = 80 V out Fin = 50 Hz DA D3 RL = 330 2

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: Create a rectifier circuit that provides an output of 100Vdc by using the following circuit: a. Half…

A: Half wave rectifier circuit. Vi=Vmsin(ωt)Vo=12π∫0πVmsin(ωt)d(ωt) =Vmπ

Q: If the maximum reverse voltage that can be applied across the silicon diode of a half-wave rectifier…

A: We need to find out output voltage waveform and dc value of output for half wave rectifier

Q: Refer to section 3.5.3 in your textbook that deals with a bridge rectifier. If the input signal is a…

A: Average voltage and Peak diode current is determined as shown below

Q: Ideal diodes 2.2 10 V 2.2 kA 2.2 ka

A: We need to find out DC value of full rectifier output .

Q: HW: For full wave 3phase rectifier, if the output de current equal to (31.061A) and the load…

Q: Assuming an ideal diode, sketch Vị, Va and ia for the half-wave rectifier below. The input is…

A: In this question, We need to determine the input voltage equation. w= 2πf = 2π×60= 120π Assume…

Q: 6.26. Calculate the average power delivered to the load for the full-wave bridge rectifier circuit…

Q: D4 D1 RL + 1.2K Vs D3 YD2 9V sin(2r 50 t) 1.b) Vs frequency is 50 Hz. Why the v̟ frequency is 100…

A: The Input frequency is 50 Hz. In the input waveform there is both positive and negative half cycle…

Q: Q3: The figure below includes a bridge full-wave rectifier circuit with a diode type is1N4007. The…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: Consider a full wave bridge rectifier, whose transformer secondary voltage is 130sinwt. If the…

Q: A pure resistive R ohm is connected to the output of the three-phase Bridge Rectifier. resistor is…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: 5. Assuming an ideal diode, sketch Vị, Va and ia for the half-wave rectifier below. The input is…

Q: A full wave rectifier supplies power to a 2kilo ohm load. The AC voltage applied to the diode is…

A: Full Wave Rectifier : For constant DC current and voltage Full wave rectifier used when positive…

Q: Q1/ a/Draw the output voltage waveform for the bridge rectifier in this figure : D 120 V ms B/ What…

A: Need to find ouput voltage and PIV

Q: please answer (vii) that is the graph

Question

A full-wave bridge rectifier with a 314 V peak sinusoidal input has a load resistor of 10.6
1. If germanium diodes are employed, what is the DC voltage available at the load?
2. Determine the required PIV rating of each diode.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Three Phase Controlled and Uncontrolled Rectifiers

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the difference between a diode and rectifier?
How is a solid-state diode tested? Explain.
What is CEMF?
In a center-tapped full wave rectifier circuit utilizing ideal diodes, if the primary voltage is 160Vpeak, the turns ratio is 8:1 and the load resistance is 860 ohms, what is the rectified dc voltage at the output? express answer in volts
In a 1-phase full wave bridge rectifier with Vs = Vm sin ωt, with R load & ideal diodes. The expression for the average value of the output voltage is 2Vm/π Select one: True False
A power diode has a reverse saturation current of 10−8 A and n =2. What is the forward voltage drop at the peak current of 100 A? What is the power dissipation in the diode in a half-wave rectiﬁer application operating at 60 Hz if the series resistance is 0.01 Ω and the conduction time is 1 ms?
A number of diodes rated at 1620 V each are to be connected in series in a rectifier circuit with a maximum voltage of 3000V. A de-rating factor of 15% is recommended. The maximum difference in leakage current of the diodes is given as 10mA , and the maximum difference in stored charge is 20µC. Calculate, 1) the number of diodes that must be used, 2) a suitable component value for the static equalization circuit; 3) a suitable component value for the dynamic equalization circuit.
Q.1 A single-phase diode bridge rectifier is connected to a grid with rms voltage V, 230V at 50 Hz. Assume that the load is highly inductive, so it could be represented by a constant dc current, Id = 10A. a) Sketch the load voltage and find the average voltage of the load? b) Sketch the source current (grid. AC side) and find the rms value of the source current? c) Determine the fundamental source current and the first three harmonics? Assume Ish_rms ³ 0.91a/h for odd hand 0 otherwise?
If a diode full wave rectifier circuit is excited by an ac source with an amplitude of 10 V and angular frquency of 100 rad/sec, then what will be the amplitude of the dc voltage obtained at the output of the rectifier? Assume no filter circuit is used.
Consider the half-wave rectifier shown in the figure below. Let vs be a sinusoidal with 10V peak amplitude with frequency of 60Hz and let R = 1000 ohms. Use the contant voltage-drop diode model with VD = 0.7 V.
A full-wave bridge rectifier with a 12V (pk) sinusoidal input has a load resistor of 20 k. (a) If silicon diodes are employed, what is the dc voltage available at the load? (b) Determine the required PIV rating of each diode. (c) Find the maximum current through each diode during conduction. (d) What is the required power rating of each diode?
3. It is required to design a full-wave rectifier circuit using the circuit shown below to provide an average output vol tage of10 V. find the required turns ratio of the transformer. Assume that a conducting diode has a voltage drop of0.7 V. The ac line vol tage is120 Vrms.