Find /1, 12, I3, and Vo in the following circuit. Use diode constant voltage drop (CVD) model with Vp, = 0.8 V. 'VịR kND1R3 kN I3VoV2I2R2 kND2The circuit parameters are:VD.= 0.8 V, V, = 6 V, V2 = 8 V, R, = 3, R2 = 8, and R3 = 81. Value of /1:2. Value of 12:3. Value of /3:4. Value of Vo

Note: Since you have posted a question with multiple subparts, we will solve the first three…

Answered: V1 R1 kN I1 D1 R3 kN 13 Vo V2 R2 kN D2

Engineering

Electrical Engineering

V1 R1 kN I1 D1 R3 kN 13 Vo V2 R2 kN D2

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where R1 and R2 are the resistances at temperatures T1 and T2, respectively, and is known as the temperature coefficient of resistance. If a copper wire has a resistance of 55 at 20C, find the maximum permissible operating temperature of the wire if its resistance is to increase by at most 20. Take the temperature coefficient at 20C to be =0.00382.
What is the difference between a diode and rectifier?
Can you help me with this homework problem? Constant voltage drop is Vd=0.7 What is the output volts of V? What is the current I going through the resistor? What is the diode current Id2? What is the diode current Id1? What are the states of two diodes D1 and D2?
Given the circuit design for a Zener diode regulator in the previous question, what is the maximum power that will be dissipated by the Rs resistor? You are told that the source voltage Vs varies from 6 V to 13 V, the load current il varies between 2 mA and 47 mA, and the diode is an ideal 4 V Zener diode. You will need to recalculate the maximum allowable resistance Rs with your new values, as part of this question. Please enter your answer to 3 significant figures, and in Watts.
In Figure-1 (a and b), calculate the load current, load voltage, load power, diode power, and total power using 3d approximation if Rp 802 and diode current is 10 mA. Note please solve within 30 minutes.avoid plagiarism
a. Using standard resistor values, what value of R1 is needed to achieve 1.18V ±0.01V at Vout? b. Using the R1 value chosen in (a) part, what happens to the voltage Vout when a load resistance of 10K is added (between Vout and ground). c. What is the minimum value of load resistance required for correct operation Zener diode is used in place of si diode. Or you can assume zener current according to requirement Answer it i will rate
Here are the sub-questions:a. Under what input conditions will D1 conduct? If D1 is conducting, what is Vo ? Express in terms of Vi if necessary.b. Under what input conditions will D2 conduct? If D2 is conducting, what is Vo ? Express in terms of Vi if necessary.c. Under what conditions will none of the diodes conduct? If none of the diodes are conducting, what is Vo? Express in terms of Vi if necessary.
Determined the range of values for Vin that will maintain the Zener diode in ON state and power dissipated in diode, for the cct in figure( 3).Vz=30volt, Rs=500Ω, Izmin=5mA,Izmax=80mA,RL=1000Ω
a. Determine VL, IL, and IR for the network of below if RL=180 ohms b. Repeat part (a) if RL=470 ohms c. Determine the value of RL that will establish maximum power condition for the Zener diode. d. Determine the minimum value of RL to ensure that the Zener diode is the the "on" state.
Diodes D1, D2, D3 and D4 are identical Silicon diodes with forward voltage drop of 0.7volts. Consider vi to be the circuit's input voltage.A) Under what input conditions will diode D1 conduct? B) If D1 is conducting, express vo in terms of vi. C) Under what conditions will diode D4 conduct? D) If D4 is conducting, express vo in terms of vi. E) Under what input conditions will none of the diodes be conducting? F) If none of the diodes are conducting, what is vo? G) The input to the circuit has the waveform shown below. Plot the waveform of thevoltage vo. Show all the important quantities in your plot.