河VD (V)ID (mA)If the relationship between the voltage VD and the currentID as shown in the following table:0.6630.7110.73518a) Determine the statistic resistance at Ip=11 mA.b) Determine the dynamic resistance at ID = 11 mA.c) Determine the average resistance for the given diode between twooperational points when the diode current values for these points are 3 mAand 18 mA.d) Find the voltage Vp if the current ID = 12 mA.e) Find the voltage V, if the current ID = 7 mA

As per Bartleby policy we can answer only three subparts at a time, so I am solving first three for…

VD (V) Ip (mA) If the relationship between the voltage V₂ and the current ID as shown in the following table: 0.66 3 0.7 11 0.735 18 a) Determine the statistic resistance at Ip=11 mA. b) Determine the dynamic resistance at Ip = 11 mA. c) Determine the average resistance for the given diode between two operational points when the diode current values for these points are 3 mA and 18 mA.

VD (V) Ip (mA) If the relationship between the voltage V₂ and the current ID as shown in the following table: 0.66 3 0.7 11 0.735 18 a) Determine the statistic resistance at Ip=11 mA. b) Determine the dynamic resistance at Ip = 11 mA. c) Determine the average resistance for the given diode between two operational points when the diode current values for these points are 3 mA and 18 mA.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 1N4748A zener diode has a ZZ of 23 Ω. Taking the data from the datasheet VZ = 22 V with a test current, IZ, of 11.5 mA. What is the voltage across the zener terminals when the current is 6 mA? When the current is 20 mA? Make the representation of the values by means of their curve characteristic.
The output of a diode used as a solar cell is given by IC =1−10−15[exp(40VC)−1] amperes What operating point corresponds to Pmax? What is Pmax? What are the values of ISC and VOC?
Use Eq. as shown to accurately calculate the voltage change required to increase the diode current by a factor of 10.
Calculate the intrinsic carrier densities in silicon and germanium at (a) 77K, (b) 300K, and (c) 450K. Use the information from the table shown.
For the Zener Diode network shown if the Fig. Determine VL, Vr, Iz, and Pz.
In the given circuit, since C= 47 μF, RL= 1 kW and Vs=90 cos200t V; What is the diode current during the one-time charging time of the capacitance?
A silicon sample is supporting an electric ﬁeld of −1500 V/cm, and the mobilities of electrons and holes are 1000 and 400 cm2/V·s, respectively. What are the electron and hole velocities? If p=1017/cm3 and n=103/cm3, what are the electron and hole current densities?
If a silicon diode's relationship between voltage and current is given by the approximation What is the diode voltage at 3.2 A for a reverse saturation current of 30 pA? Provide your response in millivolts.
A diode is operating at a current of 2A. (a) What is the diffusion capacitance if the diode transit time is 10ns?(b) How much charge is stored in the diode? (c) Repeat for iD =100 mA.
Calculate the total current of a circuit with a 9.5 V voltage source connected in series with a directly biased silicon diode and a series resistor of 440 Ω. Consider the second approximation of the diode where it is considered to be connected to a battery in series. Units of the response in milli amperes. Note: I put the original exercise in Spanish, so that it is better understood. Explain step by step, please.
A diode is tested at the presence of dc+ac source, where the diode's average current level (dc level) is 0.2 mA. Find the temperature (both in Kelvin and Celsius) if the dynamic resistance is approximately 200 ohms
The diode current in a p-n junction is modeled exponentially (given below.) When the p-n junction is polarized with 0.7V and 0.75V, the currents flowing through the diode are again measured on the basis of 1.36 mA and 7.20 mA. Accordingly, what is the ideality factor? (Note: Take the thermal voltage as mV)