Venturi meter as shown in Figure 2 has the cross-sectional area of 10 m² and 5 cm² at Point A and Point B, respectively. The height difference of the water levels in the two tubes is 16.2 cm. 61.2 cm B A Figure 2 Venturi meter a) What is the speed of water at Point A? 5 b) What is the speed of water at Point B? c) What is the pressure difference between Point A and Point B? d) If the pressure at Point A is 15 kPa, what is the pressure at Point B?

Venturi meter as shown in Figure 2 has the cross-sectional area of 10 m² and 5 cm² at Point A and Point B, respectively. The height difference of the water levels in the two tubes is 16.2 cm. 61.2 cm B A Figure 2 Venturi meter a) What is the speed of water at Point A? 5 b) What is the speed of water at Point B? c) What is the pressure difference between Point A and Point B? d) If the pressure at Point A is 15 kPa, what is the pressure at Point B?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An orifice having an area of 0.0003 m² is located on the vertical side of a tank. The tank has a constant cross sectional area of 0.40 m². It takes 312 seconds to lower the head from 1.20 m to 0.60 m. Using c=0.60, which of the following most nearly gives the head in meter after 240 seconds from an initial head of 1.20m?
a. the total dynamic head in meters b. the water power in kW c. the motor horsepower if the pump efficiency is 66%
A two floor building has two faucets, one in the basement and one in the first floor. The maximum water (\rho = 1000 kg/m3) velocity at the basement faucet, when the first floor faucet is closed, is 12m/s. The faucet diameter is 1.5 cm. Neglect all losses. (a) How much is the maximum velocity at the first floor faucet, when the basement faucet is closed? (b) What would be a maximum height (from the basement floor) for a faucet, to still get a maximum exit velocity of 5 m/s?
Hello i have an example with an answer , please show the solution since only the answer was shown in this example. And i need its solution to review properly. Thank you 1. ) Question : A pump has a brake horsepower of 35 hp with an efficiency of 68%. Neglecting frictional losses, calculate the volume flow rate (m3/min) if the discharge is raised 60 meters above.Answer: 1.82
If the velocity of a liquid is 1.65 ft/s in a 12-inch diameter pipe What is the speed of a 3-inch diameter jet coming out of a hole made in the tube?
Flow of water from a pipe connected to a tank is 10 m/s.Determine the height of the tank.
A pipe with a 2 m diameter carries water having a velocity of 4 m/s. What is the discharge in cubic meters per second and in cubic feet per second?
Installing the suitable pump to deliver 300 litres per minute. can you expline this sentence and give more data about ? please write it in the answer in print font ?
1.Find the diameter of a pipe of length 2000 m when the rate of flow of water through the pipe is 200 litres/s and the head lost due to friction is 4 m. Take the value of C = 50 in Chezy’s formula. (A short and quick answer)
Flow Speed in a Channel The speed of water flowing in achannel, such as a canal or river bed, is governed by theManning Equation,
Answer seems to be 736kpa, please show Formula and calculation as fast as (handwritten only) A 75-m-high water body that is open to the atmosphere is available. Water is run through a turbine at a rate of 200 L/s at the bottom of the water body. The pressure difference across the turbine is
A water pump motor has a horsepower rating of 11.3 HP. If it is to pump water from a well at the rate of 1 ft³/s, what is the minimum depth the well may have? The correct answer is 100 ft.