2. A square hollow steel strut with a wall thickness, t, = 10 mm is pin connected to two gusset plates, having a thickness t, = 12 mm, which are welded to the base plate having a thickness of 12 mm and fastened to a concrete base by 4 - 16 mm diameter anchor bolts. Diameter of the pin is 16 mm. Compressive load P = 40 KN , 0 = 30°. P sırut a) Calculate the bearing stress between the strut and the pin in MPa. gusset plate i=12 mn b) Calculate the shear stress in the pin in MPa. c) Calculate the shear stress in the anchor 0=30° bolt in MPa. 12 16 mm g anchor boli 4- 16 mm e

2. A square hollow steel strut with a wall thickness, t, = 10 mm is pin connected to two gusset plates, having a thickness t, = 12 mm, which are welded to the base plate having a thickness of 12 mm and fastened to a concrete base by 4 - 16 mm diameter anchor bolts. Diameter of the pin is 16 mm. Compressive load P = 40 KN , 0 = 30°. P sırut a) Calculate the bearing stress between the strut and the pin in MPa. gusset plate i=12 mn b) Calculate the shear stress in the pin in MPa. c) Calculate the shear stress in the anchor 0=30° bolt in MPa. 12 16 mm g anchor boli 4- 16 mm e

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.2P: Truss members supporting a roof are connected to a 26-mm-thick gusset plate by a 22-mm diameter pin,...

See similar textbooks

Similar questions

A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A plane truss has joint loads P, 2P, and 3P at joints D. C, and B. respectively (see figure) where load variable P — 5200 lb. All members have two end plates (see figure For Prob. 1.8-2) that are pin-connected to gusset plates. Each end plate has a thickness/ — 0.6.2.5 in., and all gusset plates have a thickness tg= 1.125 in. IT the allowable shear stress in each pin is 12,000 psi and the allowable bearing stress in each pin is 18.000 psi, what is the minimum required diameter dminof the pins used at either end of member BE1
An aluminum tube is required to transmit an axial tensile force P = 33 k (sec figure part a). The thickness of the wall of the tube is 0.25 in. (a) What is the minimum required outer diameter d minif the allowable tensile stress is 12.000 psi? (b) Repeat part (a) if the tube has a hole of a diameter J/10 at mid-length (see figure parts b and C).
A plane truss is subjected to loads 2P and P at joints B and C, respectively, as shown in the figure part a. The truss bars are made of two L 102 X 76 X 6.4 steel angles (see Table F-5(b): cross-sectional area or the two angles, A = 2180 mm2, and figure part b) having an ultimate stress in tension equal to 390 MPa. The angles are connected to a 12-mm-thick gusset plate at C(figure part c) with 16-mm diameter rivets; assume each rivet transfers an equal share of the member force to the gusset plate. The ultimate stresses in shear and bearing for the rivet steel are 190 MPa and 550 MPa, respectively. Determine the allowable load Pallowif a safety factor of 2.5 is desired with respect to the ultimate load that can be carried. Consider tension in the bars, shear in the rivets, bearing between the rivets and gusset plate. Disregard friction between the plates the bars, and also bearing between the rivets and the and the weight of the truss itself.
A long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete thrust blocks, as shown in the first part of the figure. The shores are evenly spaced at 3 m apart. For analysis purposes, the wall and shores are idealized as shown in the second part of the figure. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall is assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the walls is F = 190 kN. If each shore has a 150 mm X 150 mm square cross section, what is the compressive stress
A tension member is to be constructed of two pieces or plastic glued along plane pq (see figure). For purposes of cutting and gluing, the angle ?? must be between 25 and 45. The allowable stresses on the glued joint in tension and shear are 5.0 MPa and 3.0 MPa, respectively (a) Determine the angle it so that the bar will carry the largest load P. (Assume that the strength of the slued joint controls the design.) (b) Determine the maximum allowable load ?? if the cross-sectional area of the bar is 225
A large precast concrete panel for a warehouse is raised using two sets of cables at two lift lines, as shown in the figure part a. Cable 1 has a length L1 = 22 Ft, cable 2 has a length L2= 10 ft, and the distance along the panel between lift points Band D is d = 14 ft (see figure part b). The total weight of the panel is W = 85 kips. Assuming the cable lift Forces F at each lift line are about equal, use the simplified model of one half of the panel in figure part b to perform your analysis for the lift position shown. Find the required cross-sectional area AC of the cable if its breaking stress is 91 ksi and a factor of safety of 4 with respect to failure is desired.
A hollow circular tube T of a length L = 15 in. is uniformly compressed by a force P acting through a rigid plate (see figure). The outside and inside diameters of the tube are 3.0 and 2.75 in., respectively. A concentric solid circular bar B of 1.5 in. diameter is mounted inside the lube. When no load is present, there is a clearance c = 0.0I0 in. between the bar B and the rigid plate. Both bar and tube are made of steel having an c[autoplastic stress-strain diagram with E = 29 X LO3 ksi and err= 36 ksi. (a) Determine the yield load Pt- and the corresponding shortening 3yof the lube. (b) Determine the plastic load Ppand the corresponding shortening Spof the tube. (c) Construct a load-displacement diagram showing the load Pas ordinate and the shortening 5 of the tube as abscissa. Hint: The load-displacement diagram is not a single straight line in the region 0 ^ P ^ Pr
Continuous cable A DB runs over a small friction less pulley al D to support beam OABC, which is part of an entrance canopy for a building (see figure}. The canopy segment has a weight W = 1700 lb that acts as a concentrated load in the middle of segment AB. (a) What is the maximum permissible value of load P at C if the allowable force in the cable is 4200 lb? (b) If P = 2300 lb, what is the required diameter of pins A, B, and D? Assume that the pins are in double shear and the allowable shear stress in the pins is 10 ksi.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is the greatest length (meters) it can have without breaking if the pipe is suspended in the air and the ultimate strength (or breaking strength) is 550 MPa? (b) If the same riser pipe hangs from a drill rig at sea, what is the greatest length? (Obtain the weight densities of steel and sea water from Table M, Appendix I. Neglect the effect of buoyant foam casings on the pipe.)
Continuous cable ADS runs over a small Frictionless pulley at D to support beam OABC that is part of an entrance canopy Tor a building (see figure}. Assume that the canopy segment has a weight it' = 1700 lb. (a) Find the required cross-sectional area of cable ADB if the allowable stress is 18 ksi. (b) Determine the required diameter of the pins at O. A, R and D if the allowable stress in shear is 12 ksi.