A wall consists of a concrete layer on the outside and a wood layer on the inside.WThe concrete on the outside is 8.00cm thick and has a thermal conductivity of 0.500-m·KWThe wood on the inside is 4.00cm thick and has a thermal conductivity of 0.180-Them.Koutside temperature is 7.00°C and the inside temperature is 22.00°C. The surface area of thewall is 20.0m2.a.What is the rate of heat flow through the wall?b. What is the temperature in between the concrete and the wood?

givenoutside temp= 7.00°cinside temp=22.00°csurface area of wall= 20.0m3

W concrete on the outside is 8.00cm thick and has a thermal conductivity of 0.500- m.K W wood on the inside is 4.00cm thick and has a thermal conductivity of 0.180- The m·K side temperature is 7.00°C and the inside temperature is 22.00°C. The surface area of ti Il is 20.0m?. a. What is the rate of heat flow through the wall? b. What is the temperature in between the concrete and the wood?

W concrete on the outside is 8.00cm thick and has a thermal conductivity of 0.500- m.K W wood on the inside is 4.00cm thick and has a thermal conductivity of 0.180- The m·K side temperature is 7.00°C and the inside temperature is 22.00°C. The surface area of ti Il is 20.0m?. a. What is the rate of heat flow through the wall? b. What is the temperature in between the concrete and the wood?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.16P: 3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer...

See similar textbooks

Similar questions

2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer coefficient on one side is and on the other side is . If the temperature of both streams is suddenly changed from 38°C to 93°C, determine how long it takes for the copper plate to reach a temperature of 82°C.
There are 3 windows in a room with a width of 100 cm and a height of 150 cm.There is a single glass (k=0. 9 W/mK) of 5 mm thickness in the windows initially. Instead of these glasses to save heatYou are considering replacing it with double glazing consisting of 5 mm glass and 12 mm air (k=0.022 W/mK). Indoor and outdoor environmenttemperatures are 20 0C and -10 0C, respectively, and the heat transfer coefficients are 7 W/m2 K and 25 W/m2 K. The total heat loss in the room is 3.5 kW.when switching to double glazing;a) Find the decrease in heat transfer. b) Considering that the heat given by the heaters remains 3.5 kW, what would the room temperature be?
Consider a steam pipe of length L = 26 m, inner radius ? = 5 cm, outer radius ? = 7 cm, and thermal conductivity k = 25 W/m·K, as shown in Fig. The inner and outer surfaces of the pipearemaintainedataveragetemperaturesof? =120°Cand? =50°C,respectively.Obtain a general relation for the temperature distribution inside the pipe under steady conditions and determine the rate of heat loss from the steam through the pipe.
A horizontal pipe having a surface temperature of 67 °C and diameter of 25 cm is buried at a depth of 1.2 m in the earth at a location where k = 1.8 W/m-°C. The earth surface temperature is 15 °C. Calculate the shape factor if the pipe length is 10 m.
A plane wall (0.8 m x 0.6 m) at 10 oC is to be heated by attaching 7-cm-long, 3-mm-diameter pin fins (k=200 W/mK, ρ=5000 kg/m3) to it. nfin=200 fins are to be used in total. Temperature of the surrounding fluid is 100 oC, and the heat transfer coefficient on the surfaces is 35 W/m2K. Total (material + manufacturing) cost of the fins is 850 TL/kg. Fill the table below by neglecting heat transfer from the fin tips. nfin=? a) Fin efficiency b) Fin effectiveness c) Overall fin effectiveness d) Total cost of fins
The blades of a wind turbine turn a large shaft at a relatively slow speed. The rotational speed is increased by a gearbox that has an efficiency of 0.93. In turn, the gearbox output shaft drives an electric generator with an efficiency of 0.95. The cylindrical nacelle, which houses the gearbox, generator, and associated equipment, is of length L = 6 m and diameter D = 3 m. If the turbine produces P = 2.5 MW of electrical power, and the air and surroundings temperatures are T = 25 oC and Tsur = 20 oC, respectively, determine the minimum possible operating temperature inside the nacelle. The emissivity of the nacelle is 0.83, and the convective heat transfer coefficient is h = 35 W/m2 .K. The surface of the nacelle that is adjacent to the blade hub can be considered to be adiabatic, and solar irradiation may be neglected. Use Fin or N number of fins to reduce the Ts of the nacelle less than 143 oC
A 12 cm outside diameter and 10-cm inside diameter cast iron pipe with conductivity of 80 w/m-K has 4cm of polystyrene insulation with a conductivity of 0.027 w/m-k. saturated steam at 5000 C is flowing through the pipe and the outside surface temperature is 60 C. determine the heat transfer per 150 meter of pipe.
/ Hot square plate (1 m ×1 m) is to be cooled by attaching aluminum circular pin fins (D=0.25 cm, L= 3 cm) distributed with distance 0.6 cm as illustrated in Figs.(1-a) & (1-b). If the fin base temperature is 100°C, cooling air temperature is 30°C and h= 35 W/m. °C. Determine the total rate of heat transfer from the finned plate and the effectiveness of the fins? Assume k= 237 W/m.°C and nr=tanh mL/ mL.
: The wall of a cold storage is made of 16 cm thick brick, the outer part, then 10 cm thick plastic foam and the inner part, 2 cm thick wooden layer, with a surface area of 30 m2. The temperature of the outside air is 25 oC and the temperature inside the warehouse is -3 oC. If the film heat transfer coefficient between the air in the warehouse and the wooden layer is 29 W/m2 oC and the film heat transfer coefficient between the brick layer and the outside air is 12 W/m2 oC, calculate the heat transferred per HOUR. (wood= 0.17 W/m.K, foam= 0.024 W/m.K, brick= 0.98 W/m.K)
A 12cm outside diameter and 10cm inside diameter cast iron pipe with conductivity of 80W/m-K has 4 cm of polystyrene insulation with conductivity of 0.027W/m-K. Saturated steam at 500degC is flowing through pipe and the outside surface temperature is 60degC. Determine the temperature of the outside surface of the pipe.
The interior of a refrigerator has inside dimensions 60 cm x 45 cm base area and 120 cm high. The composite wall is made of 3 mm mild steel sheets (k=40.278 W/m-oC) with 6 cm of glass wool (k=0.052 W/m-oC) insulation sandwiched between them. The average values of convective heat transfer coefficients at the interior and exterior wall are 11.33 W/m2-oC and 14.53 W/m^2-oC, respectively. (a) Draw and label the schematic layout and the equivalent thermal circuit, (b) Calculate the individual resistance of this composite wall and the resistances at the surfaces. (c) For the air temperature inside the refrigerator at 6.5 oC and outside of 25 oC, determine the rate at which heat must be removed from the refrigerator.