Problem 2.Fluid circulates steadily through four devices in apower plant as shown in the sketch. Mass flowrates and enthalpies per unit mass are tabulated forsome of the states. Heat- and work-interactionråtes are tabulated for some of the devices.Complete the following tables:hState (kg/s) (J/kg)Device(W)(W)ADB115A.15021330325C3.4.5

Answered: Image /qna-images/answer/94979fcb-e10c-4f63-a08f-2c91d556e12f.jpg

Answered: W State (kg/s) (J/kg) Device (W) (W) A…

Engineering

Mechanical Engineering

W State (kg/s) (J/kg) Device (W) (W) A Wo B 15 A. 150 13 B 30 C 25 9. C D 5 123 4S

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

You are being tasked as a wind tunnel engineer to investigate the performance of newly designed high-speed wind tunnel in UPNM. An exhaust gas flows through a nozzle where the inlet area is 5,000 cm2.At this inlet, the gas has a velocity of 1,200 m/s, temperature of 1,500oC,and pressure of 6,000 kPa. Initial measurement revealed that the pressure at the exit of the wind tunnel is 100 kPa. Based on this information, analyze and investigate ; i. Mach number at inlet of the nozzle ii. The velocity of gas at exit iii. The area of the nozzle at exit Take specific heat ratio for the exhaust gas, ? to be 1.7 and the gas constant, R to be 205 J/kg.
(Q5] (a) The chamber contains 0.05 m' of ideal gas at a pressure of 20 KPa. The gas is subjected to an isothermal compression. until pressure reaches to 30 KPa. After that the gas is subjected to compression according to PV 2-const until pressure reaches to 40 KPa then an isobaric compression is done till volume reaches 0.005 m3. Assume that no loss in gas during the whole process : I- Sketch the process on P-V diagram and P-T diagram II- Find the work done during the entire process and temperature at end of each process.. gas
QUESTION 1 Steam at 350 °C and 1.8 MPa enters a turbine with a velocity of 100 m/s. P/p = 3141.2 kJ/kg (flow energy) and the mass flow rate is 4.0 kg/s. What is the rate of mechanical energy transfer (power) due to the mass flow? Attach File Browse Local Files
We give: AB: adiabatic trigger such as VB = 2 VA AC: isothermal compression PA =1bar=105 Pa , VA = 10^-2 m3 Gas temperature at point A: TA= 300 Kelvin Perfect gas constant: R = 8,31 J.mol-1.K-1 Molar thermal capacity at constant pressure:Cp = 29 J.mol-1.K-1 Calorific capacity ratio of this gas: Cp/Cv = 1,40 4 – Calculate the amount of QBC heat and WBC work received by the system for the transformation that changes the system from state B to state C.5 – a – Why is the UCA internal energy variation of the gas zero during the CA transformation? b – Apply the first principle to the ABCA cycle and deduce the WAB work received by the gas during theadiabatic relaxation AB.c – Interpret the WAB sign.
Topic: Heat transfer Completely solve and box the final answer. 5. Water flows at 5m/s is passed through a tube of 2.5 cm diameter, it is found to be heated from 20degC to 60degC. The heating is achieved by condensing steam on the surface of the tube and subsequently the surface temperature of the tube is maintained at 90degC. Water properties are as follows: density=995kg/m3, kinematic viscosity=.657x10-6 m2/s, Pr=4.43, k=.628W/mK, cp=4178J/kgK. Find the thermal coefficient.
A liquid reactant solution is pumped through a pre-heater before entering a reaction vessel. The solution enters the pre-heater at 25 °C and must enter the reactor at 45 °C. The flow of the reactant solution is 1500 mL per minute. The density of the reactant solution is 0.91 g-cm3 and the heat capacity is 1.75 Jg1.K1. ASsume there is no heat loss in the pre-heater or between the pre-heater and the reactor. a. Draw a schematic of the pre-heater, detailing all mass and energy flows. b. Clearly define a system boundary. c. Write the general energy balance, and a simplified energy balance stating all assumptions that apply to this problem. d. What is the minimum power rating required for the pre-heater?
Using Marshall method to design an asphalt mix, the data in theTable below were obtained. The bulk specific gravity test were conduct at 25°cwhere γ water=1gm/cm³. The values of corrected stability (kN), flow (mm) and theoreticalmaximum specific gravity of asphalt mixtures for each asphalt cement percentare given in the Table below. If the value of bulk specific gravity ofaggregate mixture is(Gbam= 2.655), determine the optimum asphalt content andcheck if the value of Marshall properties at O.A.C satisfied the Iraqi StateCommission for Roads and Bridges (SCRB) requirements? What are you suggest ifone property not satisfied the (SORB) requirements?
An perfect gas of a specific composition Molar weight is 25 grams per mole and specific heat is 3 grams per mole. Y is initially at 200kPa and 2m3 in volume. Heat transmission resulted in a twofold increase in volume. Calculate how much heat was transferred if it was subjected to a process defined by 'n=1', "n=Cp/Cv," or "n=2."
6. 308 Moles of He has pressurized to 17167kPa at 20*Ccylinder 20cm diameter at 1m^3 20*C water bath at sea levelwhat is the initial height of the piston before weights are placed on the piston How much mass is needed before achieving desired pressure How far does the piston move after weights are put on the piston
none m_cv2-m_cv1=m_in-m_out For ideal gases, .. is a function of temperature only specific volume none pressure density internal energy The quality of the fluid is 20%. Its internal energy at saturated liquid state is 200 3Jikg and saturated vapor state is 900 kJ/kg. Determine its internal energy?
Air is compressed by a compressor in steady-state operation, i.e. the inlet mass flow rate qm is constant in time. The compressor is airtight. The area of the inlet and outlet cross-section is A and AOUT, respectively. The outlet-to-inlet density ratio is PouT PIN the outlet-to-inlet mass flow rate ratio is 9m-OUT/9m-IN- What is the outlet-to-inlet volume flow rate ratio? 9V-OUT/av-IN =? Select one: a. 9V-OUT/av-IN = (A OUT'A IN) (POUT PIN b. 9V-OUT/av-IN = PIN/POUT C. 9V-OUT/av-IN = 9m-OUT/ 9m-IN d. 9V-OUT/av-IN=AOUTAIN
Find the mass flow rate (in grams per second) of water for a control volume system, if the volume flow rate is 2 liter per second. [Pwater = 1 Lem Volume flow rate=2(liter's) Mass flow rate? (g/s)