Wall A is insulated at x=0 and experiences a uniform endothermic reactions (negative heat generation) and wall B is exposed to water as shown. i- Sketch the steady state temperature distribution on T-x plot (similar to shown below) for the composite wall ii- Calculate the value of heat generation in wall A if T2 = 70°C.

Wall A is insulated at x=0 and experiences a uniform endothermic reactions (negative heat generation) and wall B is exposed to water as shown. i- Sketch the steady state temperature distribution on T-x plot (similar to shown below) for the composite wall ii- Calculate the value of heat generation in wall A if T2 = 70°C.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.63P: 1.63 Liquid oxygen (LOX) for the space shuttle is stored at 90 K prior to launch in a spherical...

See similar textbooks

Similar questions

1.63 Liquid oxygen (LOX) for the space shuttle is stored at 90 K prior to launch in a spherical container 4 m in diameter. To reduce the loss of oxygen, the sphere is insulated with superinsulation developed at the U.S. National Institute of Standards and Technology's Cryogenic Division; the superinsulation has an effective thermal conductivity of 0.00012 W/m K. If the outside temperature is on the average and the LOX has a heat of vaporization of 213 J/g, calculate the thickness of insulation required to keep the LOX evaporation rate below 200 g/h.
Find the steady-state temperature distribution in a metalic plate 20 cm by 60 cm if the two adjacent plates are held at 200 degree and the other two sides at zero degree.
There is a long cylinder inside an oven and we are using lumped capacitance method to find the temperature at its extremes. The temperature at the centre of the cylinder is 1000 C, what will be the temperature at its one end where it is away from heat source according to our calculations? not sufficient information more than 1000 C equal to 1000 C less than 1000 C
(a) The temperature at the surface of the heating rod, T1. (b) If the salt solution temperature is 300 degree Celcius, what is the value of convection heat transfer coefficient, h of the salt solution ? (c) If the heating rod is not covered by metallic cylinder and corresponds to the result of part (a) and (b), how much the rate of energy transfer to the salt solution ? (d) Compare and discuss the difference of heat transfer with and without the matallic cylinder.
c) What is the temperature of the iron heating element at x=30mm (in ∘C)? Use the origin defined in the given diagram. d) At which position x (in mm) does the iron heating element experience its highest temperature? e) In this scenario outlined in this question (constant heat generation under steady-state, 1-D conditions), can the temperature distribution in the iron ever be linear? Yes or No? Justify your reasoning.
Q3. What is the analogical reason between heat transfer by conduction and flow of electricity through ohmic resistance? Use a composite wall of a building to illustrate the concept. A composite slab with three layers of thermal conductivities k1, k2, k3 and thickness t1, t2, t3 respectively, are placed in a close contact. Derive an expression from the first principle for the heat flow through the composite slab per unit surface area in terms of the overall temperature difference across the slab.
What is the analogical reason between heat transfer by conduction and flow of electricity through ohmic resistance? Use a composite wall of a building to illustrate the concept. A composite slab with three layers of thermal conductivities k1, k2, k3 and thickness ti, t2, të respectively, are placed in a close contact. Derive an expression from the first principle for the heat flow through the composite slab per unit surface area in terms of the overall temperature difference across the slab.
Question 5: Assume steady-state, one-dimensional heat conductionthrough the symmetric shape shown in Figure 1.Assuming that there is no internal heat generation, derivean expression for the thermal conductivity k(x) for theseconditions: A(x) = (1 -x), T(x) = 300(1 - 2x -x3),and q = 6000 W, where A is in square meters, T inkelvins, and x in meters. Consider x= 0 and 1
Consider a steel alloy plate that is 10 ft long and 6 ft wide and is insulated on its flat surfaces. Suppose that left edge is maintained at 1000 °F and the other three edges are all maintained at 50°F. Solve for the temperature profile. Please show complete solution.
(a) What is the rate of heat transfer through a wall that is 2 m high by 2.5 m wide?(b) Sketch the temperature distribution.
A long wire of diameter D = 2 mm is submerged in an oil bath of temperature T∞ = 23°C. The wire has an electrical resistance per unit length of Re′=0.01 Ω/m. If a current of I = 180 A flows through the wire and the convection coefficient is h = 529 W/m2 · K, what is the steady-state temperature of the wire? From the time the current is applied, how long does it take for the wire to reach a temperature that is within 2°C of the steady-state value? The properties of the wire are ρ = 2,334 kg/m3, c = 537 J/kg · K, and k = 43 W/m · K.
An AISI stainless steel spherical canister is bath-cooled to store chemicals. The properties of the canister and chemicals are illustrated in the figure below. The inner wall heat flux is qi" = 10 kW/m2. a) Determine the initial rate of change of the canister temperature at the outer wall b) Determine the steady-state inner and outer wall temperatures