Water at 15°C is drained from a large reservoir using two horizontal plastic pipes connected in series. The first pipe is 20 m long and has a 10-cm diameter, while the second pipe is 35 m long and has a 4-cm diameter. The water level in the reservoir is 18 m above the centerline of the pipe. The pipe entrance is sharp-edged, and the contraction between the two pipes is sudden. Neglecting the effect of the kinetic energy correction factor, determine the discharge rate of water from the reservoir.

Q: Water at 15°C is to be discharged from a reservoir at a rate of 18 L/s using two horizontal cast…

A:

Q: A 3-m-high large tank is initially filled with water. The tank water surface is open to the…

A: Draw a diagram for the problem. According to the question, the kinetic energy correction factor can…

Q: Water is to be withdrawn from an 11.2-m-high water reservoir by drilling a 4.1-cm-diameter hole at…

A:

Q: Oil with p = 865 kg/m³ and µ = 0.24 kg/m. s is flowing through a 2 cm diameter pipe that discharges…

A: Given Density = 865 kg/m3 Viscosity coefficient = 0.24 kg/ms Diameter of the pipe = 2cm = 0.02 m…

Q: A submersible pump with a shaft power of 10 kW and an efficiency of 80 percent is used to pump water…

A: As per given question we have  determine the discharge rate of water and the pressure difference…

Q: Oil at 20°C is flowing through a vertical glass funnel that consists of a 20-cm-high cylindrical…

A: Given: The diameter of pipe = 1 cm The height of cylindrical reservoir = 20 cm The height of the…

Q: Water is flowing through a 10-cm-diameter water pipe at a rate of 0.1 m3/s. Now a diffuser with an…

A: Given: The of pipe at the section of bolt, d = 10 cm The diameter of the pipe at the exit, D = 20 cm…

Q: 1. Water (p = 1000- kg H = 10-3 flows in a horizontal constant-area pipe; the pipe cross ms section…

A:

Q: A 3.5 m-diameter tank is initially filled with water 2.25 m above the center of a sharp-edged…

A:

Q: A 73-percent efficient 12-hp pump is pumping water from a lake to a nearby pool at a rate of 1.2…

A: The useful pumping power and the corresponding pumping head; Pumping head:

Q: Water at 15°C is to be discharged from a reservoir at a rate of 18 L/s using two horizontal cast…

A:

Q: Water from a reservoir is pumped over a hill through a pipe 30 cm in diameter, and a pressure of 250…

A: Given dataDiameter of the pipe d = 30cmPressure P = 250kPaHead maintained H= 100mHead loss due to…

Q: 02: Water is to be withdrawn from a 3 m high water reservoir by drilling a 1.5 cm diameter hole at…

A: Volume flow rate of a fluid through a section is rate at which volume of the fluid flows, and it can…

Q: ater at 15°C is to be discharged from a reservoir at a rate of 18 L/s using two horizontal cast iron…

A: Reynolds number

Q: A very large tank contains air at 102 kPa at a location where the atmospheric air is at 100 kPa and…

A: Pressure of air in the tank Pa = 102 kPa Atmospheric pressure, Patm = 100 kPa Temperature, T= 20°C…

Q: Water flows at a rate of 20.n L/s through a horizontal pipe whose diameter is constant at 3 cm. The…

A: Given Data The change in pressure is: ∆P=2 kPa=2×103 Pa The density of the water is: ρ=1000 kg/m3…

Q: hile traveling on a dirt road, the bottom of a car hits a sharp rock and a small hole develops at…

A: Calculateing the intial velocity of the gasoline at hole-u=2ghWhere-g= accerleration due to…

Q: A 3-m-diameter tank is initially filled with water 2 m above the center of a sharp-edged…

A: Given data

Q: The pump in the figure is used for washing the boiler pipes in a thermal power plant. When the pump…

A:

Q: Water flows through a 90 degree elbow connected to a pipe with diameter of 1.5 cm. At inlet pressure…

A:

Q: Q4:- Water is pumped from a lower reservoir to a higher reservoir by a pump that provides 20 kW of…

A: Given Data P=20 kW H=45 m Q=0.03 m3/s

Q: Underground water is pumped through a 10-cm- diameter pipe that consists of a 2-m-long vertical and…

A:

Q: Consider laminar flow of water in a 0.8-cm-diameter pipe at a rate of 1.15 L/min. The velocity of…

A: Given: The diameter of the pipe, D = 0.8 cm The flow rate of pipe, Q= 1.15 L/min

Q: Water is to be withdrawn from an 8-m-high water reservoir by drilling a 2.2-cm-diameter hole at the…

A: Using the energy equation,

Q: Water at 15° C is drained from a large reservoir using two horizontal plastic pipes connected in…

A:

Q: Consider a pipe that branches out into two parallel pipes and then rejoins at a junction downstream.…

A: Given: The diameter of the first pipe is d=2 cm. The diameter of the second pipe is D=4 cm. The flow…

Q: In a pumping system handling water, the surface level of water in the open suction tank is 3m below…

A: Inlet conditions, diameter of pipe=d1= 7.62 cm =0.0762 m discharge =Q= 0.0126 m3/s friction factor =…

Q: Q.3) Water is pumped from a lower reservoir to a higher reservoir by a pump that provides 20 kW of…

A: Givenpower provided by pump to water P=20kWZ=45mhL=23m

Q: The compressed air requirements of a textile factory are met by a large compressor that draws in 0.6…

A: Given: The value of volumetric flow rate at the inlet is, Qin=0.6 m3s. The diameter of the…

Q: An inverted 3-m-high conical container is initially filled with 2-m-high water. At time t = 0, a…

A: Write the expression of the conservation of mass for a control volume process. Write the expression…

Q: The driving force for fluid flow is the pressure difference, and a pump operates by raising the…

A: As per given data, del P = 5 kpa, power input = 7 kw. maximum volume flow rate Q (m^3/s) = ? for…

Q: The velocity profile in fully developed laminar flow in a circular pipe of inner radius R = 4 cm, in…

A: given data as per the question Radius of pipe = 4 cm Velocity profile in fully developed laminar…

Q: Consider a pipe that branches out into two parallel pipes and then rejoins at a junction downstream.…

A: Given Data: The length of both pipes is the same L1=L2. The friction factors of both pipes are the…

Q: The compressed air requirements of a textile factory are met by a large compressor that draws in 0.6…

A: Properties of air at 60 degrees Celsius are: The roughness of the galvanized steel pipe is Given…

Q: The water in an 5.2 m-diameter, 6.6 m-high above-ground swimming pool is to be emptied by unplugging…

A:

Q: Water at 15°C is to be discharged from a reservoir at a rate of 18 L/s using two horizontal cast…

A: Given: Discharge is Q=18 L/s=0.4 m3/s, height of the reservoir is h=30m,length of the first pipe…

Q: The water is to be pumped from the lower reservoir to the upper reservoir at a flow rate of 8 kg/s.…

A: Pump  Pump is a hydraulic device which is used to lift liquid from low height to the high elevation.…

Q: A 3-m-high large tank is initially filled with water. The tank water surface is open to the…

A: From the given data, The static suction head of the pump, hs=-3m The static discharge head of the…

Q: A D0 = 10-m-diameter tank is initially filled with water 2 m above the center of a D =…

A: Given, The diameter of the tank, D0=10 m The diameter of the valve, D=10 cm=0.1 m The length of the…

Q: 02: Water is to be withdrawn from a 3 m high water reservoir by drilling a 1.5 cm diameter hole at…

A:

Q: A water tank is attached to a piping system with a sharp edge inlet (KL=0.5). Determine the velocity…

A: Given: The length of the system, L = 10 m The diameter of the pipe, d = 1.5 cm The friction factor,…

Q: A vented tanker is to be filled with fuel oil with ? =  920  kg/m3 and ? = 0.045 kg/m·s from an…

A: Given Data The density of the oil is: ρ=920 kg/m3 The viscosity is: μ=0.045 kg/m·s Length of the…

Q: A 3.0m diameter cylindrical tank is installed as a water tower which is used to supply water to a…

A: Given data: h1=35 mh3=5 md1=3 md2=2.5 cmd3=1.27 cmh1=35 mQ=2×10-3 m3/s Need to determine the speed…

Q: Water is flowing through a 10-cm-diameter water pipe at a rate of 0.1 m3/s. Now a diffuser with an…

A: Solution: Given data: d = 10 cm D = 20 cm Q = 0.1 m3/s

Q: Energy balance. The flow rate of water is 0.021 m'/s through a 355-m long, 11-cm-diameter pipe…

A:

Q: A hydraulic turbine is used to generate power by using water in a dam. The elevation difference…

A:

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.