Water at 20°C flows through the piping junction, entering section (1) at 0.1 m3/min. The average velocity at section (2) is 2.75 m/s. A portion of the flow is diverted through the showerhead, which contains 150 holes of 1.5-mm diameter. Assuming uniform shower flow, estimate the exit vel

Q: Before entering the engine of a BMW320D, air drawn in at 20°C and atmospheric pressure enters the…

A: Given Data The initial temperature is:Ti=20°C The volume flow rate is:V˙=120litres/minute=120×10-3…

Q: Water is pumped through a horizontal, smooth circular pipe at a bulk velocity of 0.4 m/s. The pipe…

A:

Q: Q3: A supply tank is connected to a water desalination unit by a smooth mild steel pipeline consists…

A: Given:Kinematic viscosity, ϑ=1.14 ×10-6 m2/sDischarge, Q=0.5 m3/s

Q: For a steady flow of gas in the conduit shown, what is the mean velocity at section 2?

A:

Q: Water at 20°C flows steadily through tion in Fig. P3.34, entering section 1 at 75 L/min. The average…

A: Given,  Flow rate at section 1, Q1=75 L/min=7560000m3/s=0.00125 m3/s   Average velocity at section…

Q: Air at 15°C (1atm) flows in a 5 cm x 8 cm cross section rectangular duct at a velocity of 4 m/s.…

A: Air at 15°C (1atm) flows in a 5 cm x 8 cm cross section rectangular duct at a velocity of 4 m/s.…

Q: Water at a temperature of 35 °C is flowing steadily in a 2.5 mm diameter, 15-meter long tube at an…

A: Given data as per question

Q: Water at 20°C flows steadily through the piping junction in Fig. P3.32, entering section 1 at 20…

A: Given data: Consider the diagram shown below for the different sections taken,

Q: A semi-spherical tank of radius R is completely filled with water. Now a hole of cross sectional…

A: Given Tank radius R Discharge area Ah Discharge coefficient Cd To find Time Taken to empty the tank

Q: For an incompressible Newtonian fluid in laminar flow inside a uniform horizontal pipe of constant…

A: It is required to determine outlet velocity in D2=2D1

Q: Problem 3: Octane flows steadily through the duct shown at a rate of Q = [0.2 + 0.001(M+ D) m'/s.…

A: Given data, Flow rate of octane is Q=0.2+0.001M+DQ=0.2+0.0018+10Q=0.218 m3/s Length of the duct, L =…

Q: 1. It shows that the behavior of fluid is + P. From the equation stated, show the formula vp- for…

A: Given, -dA/A=dV/V+dρ/ρ

Q: Q.3 A firm produces frozen fruits and vegetables, and a venturimeter is used in this process.In a…

A:

Q: A stream of air at 77°F and 1.2 atm absolute flowing at a rate of 225 ft3/h is blown through ducts…

A: The Rankine turbo generator is a device used to generate energy using heat in the form of fluid. For…

Q: . Water at 10 bars enters a straight evaporator tube. If the slip ratio is constant at 2.5 and the…

A: As per bartleby rules we have to answer only 1 question  Please post the remaining in another…

Q: Air at a temperature of 195oC and a pressure of 500 kPa enters a smooth insulated nozzle with an…

A:

Q: Draw a diagram to explain what it means: flow separation, the mechanism by which fluid separation…

A:

Q: What is an impact when a float moves up into the tapered vertical tube of rotameter? O a. The…

A: Rotameter is a device used for the purpose of flow measurement. In this device a float is used to…

Q: Which is not a characteristic of laminar flow. O a. Not rare in practice in water systems O b.…

A: Which is not a characteristic of laminar flow. a. Not rare in practice in water systems b. Happens…

Q: 5. The velocity profile for a fully developed laminar flow in a circular pipe of radius R is r2'…

A:

Q: Air at 100 F and 100 psia in a large tank flows into a 6-in-diameter pipe, from which it discharges…

A:

Q: Calculate the Reynolds number for the bronchial generations and identify if the flow is laminar or…

A: It is asked to find the Reynolds number for each generation

Q: A large tank open to the atmosphere is filled with water to a height of 4 m from the outlet tap. A…

A:

Q: 3. A liquid with a density of 1500kg/m flows in a horizontal pipe 11.5m long. The entrance pipe with…

A:

Q: Water is pumped through a horizontal, smooth circular pipe at a bulk velocity of 0.4 m/s. The pipe…

A: Given:Bulk velocity of water through the pipe, V=0.4 m/sInternal diameter of the pipe, d=250…

Q: A thin liquid film of ammonia (NH3), which has formed on the inner surface of a tube of di D = 10 mm…

A: Length of the tube, L=1m Inner diameter of the tube, D=10mm or D=10x10-3m Mass flow rate of air,…

Q: Two incompressible fluids (m1=2m2) are flowing at the same mass flow rates in homogenous pipes with…

A:

Q: Problem 1- Water at 10°C (p = 999.7 kg/m3 and u = 1.307 x 10-3 kg/m-s) is flowing steadily in a 5…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: When is no-slip condition possible? A. If the flow is external and the velocity is determined near…

A: The fluid property of viscosity is responsible for the no-slip condition and the formation of the…

Q: For what value of Reynolds number flow is laminar in pipes and tubes?

A: Reynold's number related the inertia force to viscous forces and it is a dimensionless number. Re =…

Q: You are designing an IC heatsink which uses round pins in cross-flow.  The heatsink must dissipate…

A:

Q: water at 40°F flows at 1000 lb/hr through a sharp-edged 1/2 in diameter which is 10 inches long. if…

A: Given that, Temperature of water, T=40 °F,Flow rate of water, Q=1000 lb/hr,Diameter of peipe, d=0.5…

Q: A water jet of diameter 20 mm is striking on a flat plate with a flow rate of 5 L/s. Determine the…

A: Given   Diameter, d = 20 mm = 0.02 m  Flow rate, Q =5 L/s = 0.005 m3/s

Q: In a circular tube of diameter 100 mm and length 13 m with laminar flow, the friction factor is…

A: Given, Frictional factor = f = 0.05   The flow is laminar. For laminar flow, Reynolds number in…

Q: Question 4: Consider laminar flow through a very long straight section of round pipe. It is shown…

A:

Q: Engine oil flows at a rate of 1 kg/s through a 5-mm-diameter straight tub a mean temperature of 80°C…

A:

Q: Comment on the trend between Reynolds number and Flow Coefficient?

A: Reynold number is a dimensionless number used to determine the type of flow across the tube or…

Q: Problem 3 Water at 20 °C (p = 998 kg/m³ and v= 1.004 x 10-6 m²/s) flows through a horizontal pipe of…

A: Given   Diameter, d = 0.1 m Velocity, v = 4 m/s Kinematic viscosity = 1.004 x 10-6 m2/s Find   Type…

Q: Water is pumped upwards from a 0.5 m diameter bed consisting of iron oxide particles with a density…

A: Given:D=0.5 mρ=5300 Kg/m3d=1 mm

Q: A typical 1-in. chlorine gas is carried by using Schedule 40 horizontal steel pipe. At a pressure of…

A:

Q: Helium at 25°C and 110 kPa (absolute) flows into a copper tube (1-1/4-standard, type M) that is 10 m…

A: copper tube114 standard,type M Do=34.925 mm Di=32.791 mm Dnom=31.75 mm m˙=.02kg/s Helium viscosity…

Q: Turbulent flow generally occurs at which among the following conditions? O the fluid has a low…

A:

Q: Oil of relative density 0.9 and a viscosity of 0.17 kg/m-s is pumped through a 75 mm diameter pipe…

A: