Water is pumped through a horizontal, smooth circular pipe at a bulk velocity of 0.4 m/s. The pipe has an internal diameter of 250 mm and a total length of 1600 m. The pipe flow is fully-developed. The shear viscosity of the water is 1 mPa.s. Calculate the power required to pump the water if the fluid flow is laminar. Provide your answer to two decimal places.

Water is pumped through a horizontal, smooth circular pipe at a bulk velocity of 0.4 m/s. The pipe has an internal diameter of 250 mm and a total length of 1600 m. The pipe flow is fully-developed. The shear viscosity of the water is 1 mPa.s. Calculate the power required to pump the water if the fluid flow is laminar. Provide your answer to two decimal places.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pipe of 0.25 m diameter carries water at the rate of 7.2 m3/s.The pressure head at the entry of the venturimeter, used to measure the flow rate in the pipe, is equivalent to 6 m of water. If the pressure head at the throat is zero, calculate the throat diameter of the venturi.Include fbd.
Water flows through the following circular pipe with a diameter of 30 mm at a speed of 3 m/s, what is the hydrodynamic entry length? The water dynamic viscosity is 1.002×10-3kg/(m⋅s).
Water flows at the rate of 0.80m3/s in a 900-m long pipe. The total head loss in the pipe is 4m. Which of the following most nearly gives the diameter of the pipe using the Darcy-Weisbach formula with f = 0.018?
Prove that the speed of an incompressible fluid through a constriction, such as in a Venturi tube, increases by a factor equal to the square of the factor by which the diameter decreases. (The converse applies for flow out of a constriction into a larger-diameter region.)
A semi-spherical tank of radius R is completely filled with water. Now a hole of cross-sectional area Ah and discharge coefficient Cd at the bottom of the tank is fully opened and water starts to flow out. Develop an expression for the time needed to empty the tank completely.
Send 20 degree Celsius of water at 4.0 [m3 / h]. How many inches of standard steel pipe should be used to set the average flow rate in the pipe to 1.5 ~ 2 [m / s]? At this time, determine the average flow rate and the flow of the fluid.
A 1.0 m radius cylindrical industrial tank filled with viscous oil to a level at a height h from its base, must be drained through a tube with a radius of 0.2 m and length L, connected to its base. The speed profile of oil in the drain tube can be described by the equation below. Where v is the oil speed, vmax is a = maximum oil speed, r is the radius, and R is the tube radius. Considering this problem situation, do what is asked in the following items, justifying your answers. a) What is the volume, in liters, of oil removed from the tank after 10 seconds, if the maximum discharge speed does the oil reach 0.35 m/s? Data: π ≈ 22/7; 1 m3 = 1000 L. b) What flow regime does the system operate? Demonstrate. Data: specific mass of oil = 800 kg/m3, specific mass of water = 1000 kg/m3, oil viscosity = 0.056 Pa.s e viscosity of water = 0.001 Pa.s.
Sketch the shear stress and velocity distribution for laminar flow across a pipe section?
Answwer with diagram and complete solution: Establish the shear stress profile, velocity profile, maximum and average velocities, and the volumetric flowrate of an incompressible Newtonian fluid flowing at a laminar condition and constant temperature through a pipe of length L and a diameter of D (or radius R). Assume that a difference in pressure induces the flow and that the flow is at a steady state.
A fluid at 20C flows at 850 cm3/s through an 8 cm diameter pipe. Determine the entrance length if the fluid is (a) hydrogen; (b) air; (c) gasoline; (d) water; (e) mercury; and (f) glycerin.
SAE 30 oil at 20°C flows in the 2.5-cm-diameter pipe as shown in the figure below, which slopes at 37°. For SAE 30 oil, take ρ = 891 kg/m3 and μ = 0.29 kg/m⋅s. Determine the flow rate in m3/h. The flow rate is m3/h.
Its relative density is 0.85, its dynamic viscosity is 1.5 Pa.find the pumping power that must be supplied to the fluid so that the mineral oil, which is s, can flow continuously with a flow rate of 10.8 m3/h through a horizontal stainless steel pipe with a length of 50 m and a diameter of 40 mm. The roughness value of stainless steel ε= 0.002 mm