Water at the initial pressure of 1 atm and temperature of 15C is flowing through a pump. Final pressure of water is 900 kPa at the outlet. Water enters through a 1-cm-diameter opening and exits through a 2.5-cm- diameter opening. Determine the velocity of the water at the inlet and outlet when the mass flow rate through the pump is 0.5 kg/s.

Water at the initial pressure of 1 atm and temperature of 15C is flowing through a pump. Final pressure of water is 900 kPa at the outlet. Water enters through a 1-cm-diameter opening and exits through a 2.5-cm- diameter opening. Determine the velocity of the water at the inlet and outlet when the mass flow rate through the pump is 0.5 kg/s.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The thrust developed by the engine of a Boeing 777 is about 380 kN. Assuming choked flow in the nozzles, determine the mass flow rate of air through the nozzle. Take the ambient conditions to be 215 K and 35 kPa.
An adiabatic diffuser is employed to decrease the velocity of an airstream from 220 to 30 m/s. The air enters the diffuser at a rate of 8 kg/s with a temperature of 300 C and a pressure of 100 kPa. Determine the exit area of the diffuser if the exit pressure is 125 kPa.
A pump increases the water presssure from 8kPa at the inlet to 700 kPa at the outlet. Water enters this pump at 41.51 degrees celsius through a 1.145-cm-diameter opening and exits through a 2.821-cm-diameter opening. Determine the velocity of the water at the outlet in m/s when the mass flow rate through the pump is 1.354kg/s. The specific volume of incoming water is 1.547x10-3m3/kg.
Nitrogen enters a steady-flow heat exchanger at 150 kPa, 10°C, and 100 m/s, and it receives heat in the amount of 150 kJ/kg as it flows through it. The nitrogen leaves the heat exchanger at 100 kPa with a velocity of 200 m/s. Determine the stagnation pressure and temperature of the nitrogen at the inlet and exit states.
The air is estimated to lose heat at a rate of 18 kJ/s during this process. Determine (a) the exit velocity and (b) the exit pressure of the air.
A desktop computer is to be cooled by a fan whose flow rate is 0.30 m3/min. Determine the mass flow rate of air through the fan at an elevation of 3400 m where the air density is 0.7 kg/m3. Also, if the average velocity of air is not to exceed 95 m/min, determine the minimum diameter of the casing of the fan.
An insulated pipe of inside diameter 50 mm contains steam of specific enthalpy2·794 MJ/kg and specific volume 0·0394 m3 /kg. The pipe then reduces to 25 mmdiameter, and the specific enthalpy is then 2·786 MJ /kg and the specific volume is0·1043 m/kg. Determine the mass flow rate of the steam and its velocity in bothsections of the pipe
The change of enthalpy of air in the cooling tower is 82 kJ/ kg and the mass flow of air is 215 kg/ min. Water enters the tower at the rate of 55 gpm at 46°C.A.) Calculate the exit temperatureB.) Determine the efficiency of the tower if the approach is 8.81°C.
A pump increases the water pressure from 8 kPa at the inlet to 700 kPa at the outlet. Water enters this pump at 41.51 degree Cecius through a 1.704-cm-diameter opening exits through a 1.154-cm-diameter opening. Determine the velocity of the water at the outlet in m/s when the mass flow rate through the pump is 1.101 kg/s. THe specific volume of the incoming water is 1.426 x 10^-3 m³/kg.
Define mass and volume flow rates. How are they related to each other?
Steam expands isentropically in a converging/diverging nozzle from inlet conditionsof 1400 kPa, 325°C, and negligible velocity to a discharge pressure of 140 kPa. At thethroat, the cross-sectional area is 6 cm2. Determine the mass flow rate of the steamand the state of the steam at the exit of the nozzle.
Air whose density is 0.078 lb/ft^3 enters the duct of an air-conditioning system at a volume flow rate of 450 CFM. If the diameter of the duct is 10 in, determine the velocity of the air in fpm at the duct inlet.