Water flow at a 250mm diameter horizontal pipe 90m long. The friction factor is 0.023. If the pressure at the starting point is 80KPA and the pressure at the end point is 50KP.. Determine the discharge at the pipe. A No answer among the choices B) Q = 132.74 L/s c) Q = 172.81 L/s D) Q = 118.43 L/s E) Q = 153.68 L/s F) Q = 101.07 L/s

Water flow at a 250mm diameter horizontal pipe 90m long. The friction factor is 0.023. If the pressure at the starting point is 80KPA and the pressure at the end point is 50KP.. Determine the discharge at the pipe. A No answer among the choices B) Q = 132.74 L/s c) Q = 172.81 L/s D) Q = 118.43 L/s E) Q = 153.68 L/s F) Q = 101.07 L/s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A horizontal pipe of 150 mm diameter for the initial 30 m and 75 mm dimeter for the remaining 10 m is connected to a water tank. The height of waler in tank is 15 m above the centre line of the pipe. Find out the flow rate through the pipe, taking all losses into the account. Consider the reduction in diameter of the pipe as sudden coefficient of friction for the pipe is 0.008.
Q.5. Determine the velocity of the flow out of the vertical pipes at A and B, if water flows into the Tee at 8 m/s and under a pressure of 40 kPa. Assume negligible head loss.
An engineer is hired to design a swimming pool 15m long by 6m wide by 2m deep. For water supply, he decideds to lay 600m of 5cm pipe with f=0.020 from a nearby main to the pool. The pipe will discharge freely into the pool during the entire filling process. The average pressure at the water main is 550kpa and the difference in elevation between the two ends of the pipe is 10m, with the discharge end higher than the intake end. Assuming that 10% of the loss in the pipeline are due to transitions, fittings and valves, how long would it take to fill the swimming pool?
Water at 15°C (? = 999.1 kg/m3 and ? = 1.138 × 10−3 kg/m·s) is flowing steadily in a 30-m-long and 6-cm-diameter horizontal pipe made of stainless steel at a rate of 10 L/s. Determine (a) the pressure drop, (b) the head loss, and (c) the pumping power requirement to overcome this pressure drop.
(b) A horizontal pipe is diverted upwards with an angle of 25 degrees. Water enters with a velocity of 4.5 ms-1 and exits upwards. The pipe entrance has a diameter of 200 mm and increases two times at the outlet. The inlet gauge pressure reads 80 kPa. If the difference vertical distance between inlet and outlet is 0.4 m, calculate the magnitude and direction of the resultant force on the pipe bend. Neglect energy losses and take the volume of water to be 0.18 m3
Fig D shows a pipe system in parallel with a total flow of 400liters per sec. Determine the flow at the 45cm pipe. For the 45cm pipe use C = 140 and for the 30cm pipe use C = 100
Determine the pressure (in kN/m2) in the pipe shown (Pressure A) if y=1.24 m, h=1.02 m, and the manometry fluid is mercury (Specific Gravity=13.6).
A 1.20 m-diameter(internal)horizontal steel penstock conveys water at the rate of3.6 m3/s. The thickness of the pipe wall is 25 mm. Thebulk modulus of elasticity of water is 2.2 GPa. The pipehas length of 1000 m and the friction factor is 0.020. Thewater surface elevation in the reservoir is 60 m. If theflow is stopped completely by closing the valve in 2sec, determine the following:(a) the maximum water hammer pressure that candevelop.(b) the maximum pressure at the valve.(c) the elongation of the pipe in mm (△=ForcexL/AE) foran almost instantaneous closure.
For this system, the discharge of water is 0.15 m3 /s, x = 1.0 m, y = 2.0 m, z = 8.0 m, and the pipe diameter is 30 cm. Neglecting head losses, what is the pressure head at point 2 if the jet from the nozzle is 10 cm in diameter? Assume α = 1.0 at all locations.
Subject hydraulics: Consider FIGURE R1M—3. Determine the discharge and the pressure head at A and B given a pipediameter of 200 mm and the exit diameter to be 150 mm. Neglect losses of head.
In a pipe 300 mm in diameter, water flows over a length of 300 m, connecting point A, at topographic elevation of 100.0 m, in which the internal pressure is 291 kPa, to point B, at topographic elevation 74 .0 m, where the internal pressure is 334 kPa. Determine the direction of flow. Data: Specific gravity of water = 10 kN/m3. A) from B to A B) There is no drain. 0 C). from A to B For the previous question, calculate the pressure drop between A and B, in meters. ( ) If the flow is equal to 0.18 m3/s, calculate the friction factor of the pipe. ( ) For this same flow rate, calculate the friction velocity. ( )
A pipe AB carries water and tapers uniformly from a diameter of 0.1 m at A to 0.2 m at B over a length of 2 m. Pressure gauges are installed at A, B and also at C, the midpoint of AB. If the pipe centerline slopes upwards from A to B at an angle of 30° and the pressures recorded at A and B are 2.0 and 2.3 bar, respectively. (1 bar = 100 kPa) Determine the flow, in m^3/s through the pipe at C neglecting all losses. (1 bar = 100 kPa). (Please round-off final answer to four decimal places) Determine the pressure in bars, recorded at C neglecting all losses. (Please round-off final answer to 2 decimal places)