Water flows in a 0.15-m-diameter vertical pipe at a rate of 0.35 m/s and a pressure of 160 kPa at an elevation of 25 m. Determine (a) velocity head at elevation of 20 m, (b) pressure head at elevation of 20 m, (e) velocity head at elevation of 55 m, (d) pressure head at elevation of 55 m. (a) Velocity head at elevations of 20 m: i (b) Pressure head at elevations of 20 m: m. (c) Velocity head at elevations of 55 m: (d) Pressure head at elevations of 55 m:

Water flows in a 0.15-m-diameter vertical pipe at a rate of 0.35 m/s and a pressure of 160 kPa at an elevation of 25 m. Determine (a) velocity head at elevation of 20 m, (b) pressure head at elevation of 20 m, (e) velocity head at elevation of 55 m, (d) pressure head at elevation of 55 m. (a) Velocity head at elevations of 20 m: i (b) Pressure head at elevations of 20 m: m. (c) Velocity head at elevations of 55 m: (d) Pressure head at elevations of 55 m:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

0il with p = 876 kg/m³ and u = 0.24 kg/m-s is flow- ing through a 1.5-cm-diameter pipe that discharges into the atmosphere at 88 kPa. The absolute pressure 15 m before the exit is measured to be 135 kPa. Determine the flow rate of oil through the pipe if the pipe is (a) horizontal, (b). inclined 8° upward from the horizontal, and (c) inclined 8° downward from the horizontal.
Water enters a tank of diameter DT steadily at a mass flow rate of m . in. An orifice at the bottom with diameter Do allows water to escape. The orifice has a rounded entrance, so the frictional losses are negligible. If the tank is initially empty, (a) determine the maximum height that the water will reach in the tank and (b) obtain a relation for water height z as a function of time.
A gas (ρ = 0.07088lbm/ft3, μ = 0.04615 lbm/ft-hr) is to be transported through a 550 ft long circular cast iron pipe at a rate of 14ft3/s. If the head loss must not exceed 60ft, determine the velocity of flow, Reynolds Number and Darcy-Weisbach Friction Factor, mass flowrate and minimum required diameter of the pipe
Water enters a tank of diameter DT steadily at a mass flow rate of min. An orifice at the bottom with diameter Do allows water to escape. The orifice has a rounded entrance, so the frictional losses are negligible. If the tank is initially empty, (a) determine the maximum height that the water will reach in the tank and (b) obtain a relation for water height z as a function of time?
A 3-m-high large tank is initially filled with water. The tank water surface is open to the atmosphere, and a sharp-edged 10-cm-diameter orifice at the bottom drains to the atmosphere through a horizontal 80-m-long pipe. The total irreversible head loss of the system is determined to be 1.5 m. Disregard the effect of the kinetic energy correction factors. Using appropriate software, investigate the effect of the tank height on the initial discharge velocity of water from the completely filled tank. Let the tank height vary from 2 to 15 m in increments of 1 m, and assume the irreversible head loss to remain constant. Tabulate and plot the results.
Explain how flow rate is measured with a turbine flowmeter, and discuss how they compare to other types of flowmeters with respect to cost, head loss, and accuracy.
36 - Water flows with a flow rate of 0.035 m³/s through a horizontal pipe whose diameter is reduced from 15 cm to 8 cm with a reduction. Since the pressure at the center of the pipe and the pressure loss from the reduction are measured at 40 kPa, which of the following is the irreversible head loss in the reduction? (Kinetic energy correction factor 1.05, v₁=2 m/s; v₂=7 m/s) a) 1.21m B) 0.90 m NS) 0.78 m D) 1.67m TO) 1.45m
Write legibly 2. Water is to be siphoned from a tank at the rate of 0.095 m3/s. The flowing end of the siphon pipe is 4.75 m below the water surface. The lost head terms are 1.5V 2/2g from tank to summit of siphon and 1.25V 2/2g from summit to end of siphon. The summit is 1.5 m above the water surface. Determine (a) the diameter of the pipe required for the siphon and (b) thepressure at the summit 2. a. diameter of pipe ____________ mm 1b. pressure at the summit______________ 2 kPa
Oil at 20°C is flowing through a vertical glass funnel that consists of a 20-cm-high cylindrical reservoir and a 1-cm-diameter, 40-cm-high pipe. The funnel is always maintained full by the addition of oil from a tank. Assuming the entrance effects to be negligible, determine the flow rate of oil through the funnel and calculate the “funnel effectiveness,” which is defined as the ratio of the actual flow rate through the funnel to the maximum flow rate for the “frictionless” case.
In a pipeline with converging diameter, will the gradient of the total energy line be steeper or milder than the gradient of the piezometric head line? Why?
Water at 75 degrees Celsius is flowing horizontally at a rate of 1.6 m^3/min in a pipe. It enters a 3-in 45 degree elbow and is diverted upwards into a connecting pipe. The diameter of the outlet is 2in. If the pressure just before the elbow is 78 kPa, determine the magnitude and direction of the force necessary to keep the elbow in place. Assume frictional losses in the elbow are negligible.
At the bottom of a pressurized water tank is a mouth with a diameter of 5 cm, where water is discharged into the atmosphere. The water level is 2 m above the outlet. The tank air pressure above the water level is 300 kPa (absolute) and the atmospheric pressure is 100 KPA. Determine the initial rate of water discharge (volumetric flow rate) from the tank, neglecting the effects of friction.