Water flows in a pipe of circular cross-section of diameter D at a mean velocity of v. The dynamic viscosity of the water is µ, the density of the water is ρ. The diameter-based Reynolds-number of the pipe flow is Re=300. What is the pipe friction factor? λ=?    a. λ = v·D·ρ/µ b. λ = 32·v·D·ρ/µ/Re c. λ = (v·ρ/µ)2 d. λ = 64/Re

Q: If we follow a scale equivalent to 1 cm - 220 N, then a 68,720 kg shall be equivalent to how many…

A:

Q: Suppose P = 2500 lb. From the frame below, determine the magnitude and direction of (1) Ax and Ay…

A: Given data P=2500 lb

Q: F1 F2 B 8 ft E |F 6 ft H. –6 ft 6 ft -6 ft NE A,

A:

Q: The power delivered to the wheels of a car is used to overcome aerodynamic drag. Compare the amount…

A:

Q: the bracket must support the four forces shown in figure. the magnitude of the resultant force is:

A:

Q: Required : 1. Determine the safest thickness of the vessel in mm 2. If the vessel has spherical…

A:

Q: The cycle net work of an air standard Otto cycle is 900 kJ/kg with a maximum cycle temperature of…

A:

Q: The 15-kg block is subjected to the force shown. Determine its velocity at s= 4m if v= 6 m/s at s=0.…

A: It is very basic question of mechanics. Used concept is Newton's second law of motion.

Q: Two moles of octane are burned with stoichiometric amount of air. How much water is formed in the…

A: When a hydrocarbon is burnt in air(oxygen-rich environment) then we get carbon-dioxide, water and…

Q: In an ideal Rankine cycle, steam is generated at 4.1 MPa and 480 deg. C. The condenser is at 32 deg.…

A:

Q: For the mechanical translation system below, find the force-voltage analogy and force-current…

A: 1)no of nodes =no of displacement  2)connect masses from nodes to reference 3)connect the other…

Q: Acceleration of an object is given by a = 90 – 6x2 cm/s2; where x is in cm. If the object starts…

A:

Q: For an aluminum structure with a fillet radius of 0.07-in, the ultimate tensile strength is 60 ksi.…

A:

Q: A fuel pump is delivering 18 gallons per minute of oil with a specific gravity of 0.80. The total…

A: Given data: Q=18 GPMSG=0.8h=75 m=246.063 ftP=1.1 hp Need to determine the efficiency of the pump.

Q: A steel band 8mm thick is to be pulled on to a cylinder 30cm in diameter. The interval diameter of…

A:

Q: We have designed a divide-and-conquer algorithm that runs on an input of size n. This algorithm…

A: a) Recurrence relation T(x) = {  2T(x/2) +Ox2           for n>c                O1…

Q: 3. The aluminum and bronze cylinders are centered and secured between two rigid end-plates by…

A:

Q: 4 kN/m 2 kN/m A| |B 2 m 3 m FIG. P4.13

A: given; draw shear force diagram and bending moment diagram; AB=2mBC=3mAC=5muniform weight density in…

Q: F1 F2 45° 4 m D 2.

A:

Q: R= 0.2 m 13.15 The rate of change of speed of the belt is given by 0.06(10 – t) m/s², where t is in…

A:

Q: For the pulley system, as shown, the velocity of object A is known. Determine the velocity of B. A…

A:

Q: Why is enthalpy generally more useful than internal energy in the thermodynamics of real world…

A: The total energy contained by the thermodynamic system is known as the internal energy of the system…

Q: I -mall metal bar, with an initial temperature of 150 C, is taken outside where the air temperature…

A:

Q: I A block R of mass 100 kg is placed on a block S of mass 150 kg as shown in the figure. Block R is…

A: Answer: The minimum force F needed to move the block S is 1.3734 kN.

Q: Show complete solution pls A steel pipe has an inside diameter of d = 250 mm and an outside…

A:

Q: x2(1) x1(t) K fv, M2 f(t) M1 fv, fv. fv,

A:

Q: A thermocouple has a transfer function of V (mV) = -5.0 + 0.5 * T( °C) (a) If the range of the input…

A: Since we only answer up to 3 subparts so we will answer first 3. Please resubmit the question by…

Q: The disk rotates with the angular motion shown. The peg at B is fixed to the disk. Suppose that w =…

A: Given Data The angular velocity is:ω=5 rad/s The angular acceleration is:α=10 rad/s2 The center…

Q: A meeting hall is maintained at 25°C the space cooling load of 40 kW of which 30 kW is sensible…

A: Since we only answer up to 3 subparts so we will answer first 3. Please resubmit the question by…

Q: A3-in. by 6-in. steel (E-29,000 ksi) bar (4-foot long) is subjected to the loads shown. Calculate…

A:

Q: Determine the length of the shortest 7.5mm diameter bronze wire which can be twisted through two and…

A:

Q: span of 0.3m. A concentrated load of 250N is then applied vertically downwards at a point 0.1m from…

A:

Q: wind tunnel nozzie consists of a smooth contraction from Az = 0.2 m². The outlet velocity is Uz =40…

A: Draw the diagram- Given -A1=0.6m2A2=0.2 m2V2=40 m/sP2=101.6 kPaP=1.225 kg/m3(constant due to in…

Q: The mass of 700 kg is suspended from a trolley which moves along the crane rail from d = 1.7 m to d…

A: Given m=700kgd=1.7mD=3.5m

Q: Briefly define the following terms (a) Systematic errors, (b) gross errors and (c) random errors.

A: Errors in Measurement  ● Here there error in Measurement will be discussed ● Systematic error, Gross…

Q: 5. A diesel fuel tank has been filled with gasoline and runs until it quits. Which of the following…

A: When the diesel tank is filled with the gasoline then the combustion process becomes abnormal It…

Q: For the hand-operated shear shown, use the resolution and composition method to determine the…

A:

Q: A multi-stage centrifugal pump discharges 1200 gpm of water at 1400 rpm with pressure head of 1200…

A:

Q: Fi Fz B 2m 45° Am 3.

A:

Q: A 1 m wide sheet of aluminum is reduced in thickness from 12 mm to 8 mm in two passes through a…

A: Initial width, b1= 1 m Initial thickness, t1= 12 mm= 0.012 m Initial length, L1= 2 m Final…

Q: x2(1) x1(t) K fv, M2 f(t) M1 fv, fv. fv,

A:

Q: H.W.4 1- Determine the shear stress at points A and B on the beam if it is subjected to a shear 100…

A: Find the transverse shear stress at point A and B.

Q: the bracket must support the four forces shown in figure. the magnitude of the resultant force is: F…

A:

Q: For the mechanical translation system below, find the force-voltage analogy and force-current…

A: Given; K1=2K2=2K3=C+3M1=1+aM2=sa=0b=7c=5 Apply balance on the system; 1.…

Q: 27. An electric calorimeter samples steam with a line pressure of 0.175 MPa. The calorimeter adds…

A: Note: As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: A 2.8m square plate is completely immersed under water in a vertical position such that the two…

A: Answer: (a) The average pressure on one side of the plate : 80.1150 kPa. (b) The average pressure…

Q: In summation of forces the representation (ZFx^2 + £Fy^2}^(1/2) is equivalent to Select the correct…

A: As per bartleby guidelines we are allowed to solve only 1st subpart if multiple subparts are posted.…

Q: A 20-ft ladder weighing 70 lb (assumed concentrated at its mid-length) rests on a vertical plane…

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: General Solution for small oscillations of a simple pendulum with length 5.0 m and mass of 2.0 kg…

A:

Q: Given the following vectors: S= 31 - j+ 5k P = 2i + 4j - 6k Q = -7i + 2j + 9k Obtain the following…

A:

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.