Water flows through a pipe as shown in the figure. The pressure at points 1 and 2 respectively is 1.83 x 10³ Pa and 1.13 x 105 Pa. The radius of the pipe at points 1 and 2 respectively is 3.15 cm and 1.22 cm. If the vertical distance between points 1 and 2 is 2.75 m, determine the following. s (a) speed of flow at point 1 m/s (b) speed of flow at point 2 m/s (c) volume flow rate of the fluid through the pipe

Water flows through a pipe as shown in the figure. The pressure at points 1 and 2 respectively is 1.83 x 10³ Pa and 1.13 x 105 Pa. The radius of the pipe at points 1 and 2 respectively is 3.15 cm and 1.22 cm. If the vertical distance between points 1 and 2 is 2.75 m, determine the following. s (a) speed of flow at point 1 m/s (b) speed of flow at point 2 m/s (c) volume flow rate of the fluid through the pipe

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter15: Fluids

Section: Chapter Questions

Problem 57PQ: Water flows through a pipe that gradually descends from a height of 6.78 m to the ground. Near the...

See similar textbooks

Similar questions

Review. The tank in Figure P15.13 is filled with water of depth d = 2.00 m. At the bottom of one sidewall is a rectangular hatch of height h = 1.00 m and width w = 2.00 m that is hinged at the top of the hatch. (a) Determine the magnitude of the force the water exerts on the hatch. (b) Find the magnitude of the torque exerted by the water about the hinges.
A horizontal pipe 10.0 cm in diameter has a smooth reduction to a pipe 5.00 cm in diameter. If the pressure of the water in the larger pipe is 8.00 104 Pa and the pressure in the smaller pipe is 6.00 104 Pa, at what rate does water flow through the pipes?
The gravitational force exerted on a solid object is 5.00 N. When the object is suspended from a spring scale and submerged in water, the scale reads 3.50 N (Fig. P15.24). Find the density of the object. Figure P15.24 Problems 24 and 25.
Water flows through a pipe that gradually descends from a height of 6.78 m to the ground. Near the top, the cross-sectional area is 0.400 m2, and the pipe gradually widens so that its area near the ground is 0.800 m2. Water leaves the pipe at a speed of 16.8 m/s. What is the difference in the water pressure between the top and bottom of the pipe?
The small piston of a hydraulic lift (Fig. P15.6) has a cross-sectional area of 3.00 cm2, and its large piston has a cross-sectional area of 200 cm2. What downward force of magnitude F1 must be applied to the small piston for the lift to raise a load whose weight is Fg = 15.0 kN? Figure P15.6
(a) Verify that a 19.0% decrease in laminar flow through a tube is caused by a 5.00% decrease in radius, assuming that all other factors remain constant. (b) What increase in flow is obtained from a 5.00% increase in radius, again assuming all other factors remain constant?
The small piston of a hydraulic lift (Fig. P14.8) has a cross-sectional area of 3.00 cm2, and its large piston has a cross-sectional area of 200 cm2. What downward force of magnitude F1 must be applied to the small piston for the lift to raise a load whose weight is Fg = 15.0 kN?
The inside diameters of the larger portions of the horizontal pipe depicted in Figure P9.45 are 2.50 era. Water flows to the right at a rate of 1.80 104 m3/s. Determine the inside diameter of the constriction. Figure P9.45
Fluid originally flows through a tube at a rate of 100 cm3/s. To illustrate the sensitivity of flow rate to various factors, calculate be new flow rate for following changes with all other factors remaining the same as in original conditions. (a) Pressure difference increases by a factor of 1.50. (b) A new fluid wit 3.00 times greater viscosity is substituted. (c) The tube is replaced by one having 4.00 times the length. (d) Another tube used with a 0.100 times the original. (e) Yet another tube is substituted with a radius 0.100 times the original and half length, and pressure difference is increased by factor of 1.50.
An incompressible, nonviscous fluid is initially at rest in the vertical portion of the pipe shown in Figure P15.61a, where L = 2.00 m. When the valve is opened, the fluid flows into the horizontal section of the pipe. What is the fluids speed when all the fluid is in the horizontal section as shown in Figure P15.61b? Assume the cross-sectional area of the entire pipe is constant. Figure P15.61
The left ventricle of a resting adult's heart pumps blood at a flow rate of 83.0 cm3/s , increasing its pressure by 110 mm Hg, its speed from zero to 30.0 cm/s, and its height by 5.00 cm. (All cumbers are averaged over the entire heartbeat) Calculate the total power output of left ventricle. Note that most of the power is used to increase blood pressure.
The inside diameters of the larger portions of the horizontal pipe depicted in Figure P9.45 are 2.50 era. Water flows to the right at a rate of 1.80 104 m3/s. Determine the inside diameter of the constriction. Figure P9.45