= Water is flowing through the nozzle of the sprinkler at a constant rate of 3 m/sec when the sprinkler rotates with an angular velocity, 2 rad/sec, and an angular acceleration, Ö= 3 rad/sec². Assuming the nozzle lies in the vertical plane, determine the magnitude of the acceleration of a water particle as it exits the open end, r 0.2 meters. Present your answer in m/sec² using 3 significant figures.

= Water is flowing through the nozzle of the sprinkler at a constant rate of 3 m/sec when the sprinkler rotates with an angular velocity, 2 rad/sec, and an angular acceleration, Ö= 3 rad/sec². Assuming the nozzle lies in the vertical plane, determine the magnitude of the acceleration of a water particle as it exits the open end, r 0.2 meters. Present your answer in m/sec² using 3 significant figures.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A man holds and drops the two equal masses without moving his arm’s length on a rotating table then the angular velocity is
2. The sprinkler head is tilted at an angle of 45 degrees to the water levelprojecting from the nozzle at a speed of 20 m/s, calculate 1.Maximum distance of water from level ground (h) 2. The horizontal distance when water hits the ground (Sx)
A pump is located near the edge of the horizontal platform shown below. Thenozzle at A discharges water with an initial velocity of 13 m/s at an angle 55° withthe vertical axis. A. Increase the height of cannon from 0 to 15 m at the increment of 1 m andcalculate the horizontal and max vertical distances at each height. B. Evaluate the change of angle of nozzle on horizontal and vertical distance atHeight of 1 m, 5m and 10 m (Try angle of 30°, 45°, 65°)
A horizontal jet of water 1 in. in diameter and having a velocity of 25 ft per second strikes against a vertical plate. (a) Determine the force (lb) on the plate if the plate is fixed.If the plate is moving in the same direction as the jet with a uniform velocity of 10 ft per second;(b) What is the relative velocity (ft/s), and(c) Determine the force (lb) on the plate.If the plate is moving in the opposite direction as the jet with a uniform velocity of 10 ft per second. (d) What is the relative velocity (ft/s), and(e) Determine the force(lb)on the plate.
The gauge pressure of water at AA is 150.5 kPakPa. Water flows through the pipe at AA with a velocity of 18 m/sm/s, and out the pipe at BB and CC with the same velocity vv. Neglect the weight of water within the pipe and the weight of the pipe. The pipe has a diameter of 50 mmmm at AA, and at BB and CC the diameter is 25 mmmm . ρwρw = 1000 kg/m Determine the xx component of force exerted on the elbow necessary to hold the pipe assembly in equilibrium. Express your answer to three significant figures and include the appropriate units. Determine the yy component of force exerted on the elbow necessary to hold the pipe assembly in equilibrium. Express your answer to three significant figures and include the appropriate units.
Since the snowmobile left the obstacle A at an angle of 40 degrees, its speed was 10 m/s and fell to the ground at point B:a) flight time, tb) horizontal distance traveled, Rc) Calculate the velocity components at Point B and the magnitude of velocity, V=Vxi + Vyj and V.
Two geometrically similar pumps are running at the speed of 1500rpm and 3000rpm. One pump has an impeller diameter of 0.40 m and lifts water at the rate of 0.03 liters/sec against a head of 20 meters. Determine the head, discharge and ratio of powers of said pump of diameter 0.25m.
A jet is flying straight and level at a speed v0 = 1300 km/h when it turns to change its course by 90° as shown. In an attempt to progressively tighten the turn, the speed of the plane is uniformly decreased in time while keeping the normal acceleration constant and equal to 8g, where g is the acceleration due to gravity. At the end of the turn, the speed of the plane is vf = 800 km/h. Determine the radius of curvature ρf at the end of the turn and the time tf that the plane takes to complete its change in course. The radius of curvature ρf at the end of the turn is ___ m.(Round the final answer to one decimal place.) The time tf that the plane takes to complete its change in course is ___ s. (Round the final answer to four decimal places.)
A 75 mm-diameter jet has a velocity of 33.5 m/s. It strikes a blade moving in the same direction at 21.3 m/s. The deflection angle is 150°. Assuming no friction, determine the final absolute velocity V2 of the water leaving the blade.
Water enters vertically and steadily at a rate of 35 L/s into the sprinkler shown, with unequal arms and unequal discharge areas. The smaller jet has a discharge area of 3 cm2 and a normal distance of 50 cm from the axis of rotation. The larger jet has a discharge area of 5 cm2 and a normal distance of 35 cm from the axis of rotation. Disregarding any frictional effects, determine (a) the rotational speed of the sprinkler in rpm and (b) the torque required to prevent the sprinkler from rotating.
The nozzle has a diameter of 40 mm. If it discharges water uniformly with a downward velocity of 20 m/s against the fixed blade, determine the vertical force exerted by the water on the blade
The gauge pressure of water at AA is 150.5 kPakPa. Water flows through the pipe at AA with a velocity of 18 m/sm/s, and out the pipe at BB and CC with the same velocity vv. Neglect the weight of water within the pipe and the weight of the pipe. The pipe has a diameter of 50 mmmm at AA, and at BB and CC the diameter is 25 mmmm . ρwρw = 1000 kg/m3 Determine the xx component of force exerted on the elbow necessary to hold the pipe assembly in equilibrium. Determine the yy component of force exerted on the elbow necessary to hold the pipe assembly in equilibrium.