last three digits of My ID number for the length (L) of the pipe in meter is (754) Water mase flow rate of 4 kg/s le delivered through the 25 mm diameter commercial steel pipe? € -0.18. The height between point 1 and 2 18 30 m.Determine the pump power required in kW.Show detalled solution stepsFor minor losses, take K for theEntrance: 0.15Exit: 0.05Bend radius: 0.35Sharp bend: 0.45Elbow = 0.25Valve: 2.5Sharp bende: 0.55Use your last three digits of your ID number for the length (L) of the pipe in mezer▷lliVoPumpScrewedregular90° elbowValvebend radiusSharpbendSharp bend

Calculate the all minor losses.…

Water mase flow rate of 4 kg/e le delivered through the 25 mm diameter commercial steel pipe? -0.18. The height between point 1 and 2 ls 30 m. Determine the pump power required in kW. Show detailed solution stepe For minor losses, take K for the Entrance: 0.15 Exit: 0.05 Bendradius: 0.35 Sharp bend: 0.45 Elbow = 0.25 Valve: 2.5 Sharp bende: 0.55 Use your last three digits of your ID number for the length (L) of the pipe in meer

Water mase flow rate of 4 kg/e le delivered through the 25 mm diameter commercial steel pipe? -0.18. The height between point 1 and 2 ls 30 m. Determine the pump power required in kW. Show detailed solution stepe For minor losses, take K for the Entrance: 0.15 Exit: 0.05 Bendradius: 0.35 Sharp bend: 0.45 Elbow = 0.25 Valve: 2.5 Sharp bende: 0.55 Use your last three digits of your ID number for the length (L) of the pipe in meer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pump is fitted to 100 m pipeline that connects reservoir A reservoir B. The diameter of the pipe is 200 mm and is characterized by a fri factor of 0.02. The design discharge is 0.15 m³/s and the pump. Assuming th minor losses are 20% of friction losses, determine the head the pump must p
Question 2) The centrifugal pump in the figure is in his preference Passing water at 25°C from the tank through the 1.22 m exchange store pumping. Inner diameter of the suction channel is 101.6 mm, in total it is 0.0306 and its length is 3.2 m. It the local coefficients of the user in the pipe are 7.4. If the pump works at a flow rate of 109 m3/h ENPY=1.52 is m. Does the pump work without cavitation at this flow? Show the calculation. For water, p=997 kg/m3 and Pb=3.169 kPa. Piping system at the entrance (Suction pipe) pump 22 Patm=101.3 kPa and 0.2=1.05. van
A centrifugal pump(efficiency 86%) lifts water through a total height of 42m from reservoir to discharge. Pumping is through 300m of 75mm diameter pipe at the rate of 20li/s. If pipe friction factor, f = 0.025, what KW is required? Answer: 9
As seen in Figure 3 below, the water from the tank 1 is pumped to the tank 2 with a flow rate of 5,664 liters/s, passing through a pipe with a diameter of 50.8 mm and a length of 121.92 m. Some of the local losses in the system are also shown on the figure. Calculate the effective power of the pump by taking the relative roughness ɛ / d = 0.001 Note: For all questions, pwater = 1000 kg/m³, g=9.81m/s^2 , the kinematic viscosity of water is 1.0219x106 m²/s and the questions can be solved by accepting the values that are not given.
A pump draws 20 m3/h of water having a density of 1000 kg/m3 from the open storage feed tank to an open overhead tank that supplies 151 J/kg to the wallowing fluid. What is the horsepower hp of the pump if it’s efficiency is 75%? The flow turbulent
Determine the pumping power (in kW) required, if water at 30°C is flowing through a pipe length of 1km with 250 mm diameter at the rate of 0.05 m³/s. Take value of Darcy friction factor as 0.04
A water pump is used to pump water from one large reservoir to another large reservoir that is at a higher elevation. The free surfaces of both reservoirs are exposed to atmospheric pressure, as sketched in Fig. The dimensions and minor loss coefficients are provided in the figure. The pump’s performance is approximated by the expression Havailable = H0 − aV.2 , where shutoff head H0 = 24.4 m of water column, coefficient a = 0.0678 m/(Lpm)2 , available pump head Havailable is in units of meters of water column, and capacity V. is in units of liters per minute (Lpm). Estimate the capacity delivered by the pump. A
At the gasoline transfer facility (ρᵣₑₗ=0,75) from the pond of storage to consumption, you want to install a pump to circulate a flow of 40(lt/s). The 400m long pipe is cast iron 150mm in diameter and consists of a check valve, a gate valve and 2 commercial medium radius elbows. The consumption tank is pressurized to 2,9 (kgf/cm²) gauge pressure. Decide the drive power of the pump in KW if its performance is 70%. •Additional data, pressure drop factors: •Retention valve Kᵣ = 1,5 •Gate valve open Kᵥ = 0,21 •Medium Radius Commercial Elbow Kc = 0,75 for each cubit •Storage pond outlet sharp angles Kₛ = 0,5 •Entrance to consumption pond Kₑ = 1 •Friction factor in pipes f = 0.026
A pipeline transporting engine oil of 3.5 m3/s at 40⁰C branches out into two parallel pipes made of commercial steel but reconnects downstream. Pipe A is 750 m long and has a diameter of 50 cm while Pipe B is 1200 m long with a diameter of 50 cm. Neglecting minor losses, determine the following:a) Flow rates (in m3/s) through pipe A and pipe B.(Hint: Assume similar flow frictional factor for initial calculations and determine the correct frictional factor using Colebrook equation).b) Actual head losses (in m) in pipe A and pipe B
In the diesel oil transfer facility (ρ rel = 0.85), from the storage tank to the consumption tank, we want to install a pump to circulate a flow of 45 lt / s. The 400m long pipe is cast 150mm in diameter and consists of a check valve, a gate valve and 2 commercial medium radius elbows. The consumption tank is pressurized to 3.8 bar of manometric pressure. Determine the drive power of the pump in kW if its performance is 68%. Additional data, load loss factors: 1. Check valve Kr = 1.5 2. Gate valve open Kv = 0.21 3. Commercial elbow of mean radius Kc = 0.75, for each elbow 4. Storage tank outlet sharp angles Ks = 0.5 5. Entrance to consumption tank Ke = 1 6. Pipe friction factor f = 0.025
Water is pumped between two reservoirs in a pipeline with the following characteristics; (d= 300mm, L= 70m, /= 0.025, minor loss coefficient: YK=2.5). The pump performance curve is approximated by the equation: H,=22.9-650° Where H, is in meters and Q is in m's. Determine the discharge Q and pump head A when two pumps in series are used for total static head (4Z=25m).
Rate the flow inside a pipe with Re = 1.8x10^4 and ε/D = 0.027. A: Turbulent totally rough B. Hydraulically smooth turbulence C. Laminar, with f=64/Re D.Transient roughness turbulence