What are the ladder ratings and their load capacity?

Q: answer c

A: a=15min b=0.005min/veh-hr c=6000veh/hr d=150veh/hr/min

Q: Compute/Derived the following: a. wall shear b. wall moment c. Reaction

A: "Since you have posted a question with multiples subparts we will solve first three for you .To…

Q: A rigid pavement of 25 cm thickness of M40 grade of concrete is supported over a subgrade having…

A: Given- slab thickness h=25 cm Poisson's ratio μ=0.15 Modulus of sub-grade reaction k=8 kg/cm3 center…

Q: The T-section shown is subjected to a design ultimate moment of M = 180kN.m. Find the require area…

A: Solution: Given: fc = 30 MPa fy = 450 MPa bf = 400 mm hf = 100 mm bw = 200 mm d = 350 mm

Q: Find the dry density of soil Saturated density =1303 Kg/m3 Water content=0.442

A: Introduction: The given question is related with Geotechnical engineering . In this question we are…

Q: 3.3m 2.2m 450N/m

A: Free body diagram:

Q: ) Analyze Assignment #02 using flexibility Method -2×/7+ 10 Hinge ♡ в EJ= constt

A:

Q: The next time you make a trip to a supermarket, ask the manager if you can measure the mass of at…

A: To find:- Does the manufacturer’s information noted on the box fall within your measurement?

Q: autocad

A: Answer : We can draw the isometric view from given orthographic view in Autocad using the following…

Q: A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of…

A: Given: Modulus of elasticity =E  Coefficient of thermal expansion Outside diameter Thickness  Length…

Q: Prob. 1.4-13. For the overhanging beam shown in Fig. P1.4-13: (a) determine expressions for the…

A:

Q: (i) the resultant force due to water pressure and the height of its line of action (ii) magnitude of…

A: Width of lock gate = 8m If there are two gates, the width of the canal = 16m Height of the lock…

Q: Find the magnitude and direction of force F1 measured counterclockwise from the positive x-axis to…

A: Given : To Find : magnitude and direction of force F1?

Q: Question 1: A-find the zero force members of the truss shown below. B-Using section method determine…

A: Given :- Truss with a single load of 10 kN at point B. Required :- A) find the zero force members of…

Q: What the requirements  for the Plumbing Design for water supply? What the requirements  for Plumbing…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: QUESTION 12 At an entrance to a toll bridge, four toll booths are open. Vehicles arrive at the…

A:

Q: Rigid bar ABCD shown in the figure is supported by a smooth pin at D and by vertical aluminum alloy…

A:

Q: A Circular primary sedimentation tank for a municipal WWTP is to be designed for an average flowrate…

A:

Q: A circular curve having coordinates given in the late: e curve length (L), Chord (C), Tangent (T),…

A: given data, Chainage of PC = 3+40 m to find chord length, tangent length, radius, deflection, length…

Q: Problem 2. Calculate the area of the closed traverse or field in square meters (using coordinate…

A:

Q: determine the moment of inertia with respect to A-A axis for the shaded area shown in the figures.

A: Given A shaded area Required  Moment of inertia with respect to AA axis

Q: A 10 m cantilever beam has a uniform load of 2.5 KN/m from left to right end. Find the maximum…

A: we will be able to get the equation of the elastic curve. where x and y are the coordinates shown in…

Q: F1-1. Determine the resultant internal normal force, shear force, and bending moment at point C in…

A:

Q: What is the value of angle θ in degrees? B. What is the magnitude of force T?

A:

Q: The width of the expansion joint is 20mm in a cement concrete pavement. The laying temperature is 20…

A: Given data: Width of expansion joint = 20 mm The joint filler compresses upto 50 % Compression of…

Q: Design an acrated grit chamber with 2 channel (Volume Dimensions, Total air Supply required and…

A:

Q: In the last 6 months, ABC Sdn. Bhd. has experienced a few cases of workplace accidents involving the…

A: There are different steps in the analysis of the safety. These steps should have to follow properly,…

Q: The flow rate in a wide rectangular open channel is 2.0m²/s per meter width. The channel bed slope…

A: Given- rectangular open channel-flow rate q=2 m2/s/mbed slope S=0.002Manning's roughness coefficient…

Q: H 800 N Į 1.5m 2.5m 400 N 200 N Į 2.0m K

A:

Q: Draw the shear force and bending moment diagram of the beam shown and identify the maximum shear…

A:

Q: Problem 2. Calculate the area of the closed traverse or field in square meters (using coordinate…

A:

Q: A straight cylindrical bar is 15 mm diameter and 12 m long. It is simply supported at its two ends…

A: Given, Diameter of bar= 15mm Length=L= 12m W=90N Central deflection, yc = 5mm Buckling load=?…

Q: A 000 B D 450 lb 4 ft C

A:

Q: We presented Newton’s Law of Gravitation. We also explained the acceleration due to gravity. Create…

A: The acceleration due to gravity , g can be represented as a function of distance from Earth's…

Q: 1. Two structural members B and C are bolted to bracket A. Knowing that both members are in tension…

A: GIVEN : Two structural members having tension of magnitude P & Q respectively. P = 10 kN Q = 15…

Q: 3. The unit weight of a soil is 100 lb/ft³. The moisture content of this soil is 20% when the degree…

A: Given : Weight of soil = 100 lb/ft3 Moisture content = 20 % degree of saturation = 55% To find : A )…

Q: A long natural slope in an over-consolidated clay (c=10kPa, p=25deg, ysat=20kN/m3) is inclined at 10…

A: Given data,  c= 19kN/m² Φ= 25° Ysat= 20kN/m³ H= 5m Yw= 10kN/m³ i= 10° Factor of safety=?

Q: by using Stiffness Method and also draw SFD and BMD

A: Stiffness method Direct approach method Take EI =constant

Q: Calculate the pH of a solution that has a pOH of 8.70.

A: Introduction : The given question is related with environmental engineering . In this question we…

Q: The population growth (P) at any time in a city is governed by the equation dP (B-Dr)P, where r is…

A: Given,  B = 0.1 D = 10-6  Po = 10000

Q: An upward flow of oil (mass density 800 kg/m³, dynamic viscosity (0.8 kg/m-s) takes place under…

A: Solution: Given: mass density, ρ = 800 kg/m3 dynamic viscosity, μ = 0.8 kg/m-s pipe diameter, D =…

Q: The density of population over 40 hectares is 250/hectare. If water supply demand per day is 200…

A: Given data- Area=40 hadensity of population=250/hawater supply per day=200 litressewage…

Q: Problem 3 Tangent segments intersect at station 25+15. The azimuth between the PC and the PI is 42…

A:

Q: Proposed a number of upgrades to the existing BMS

A: There should be the proper upgradation of the BMS for the better life of the building. The proper…

Q: Rigid bar ABC is supported by bronze rod (1) and stainless steel rod (2) as shown in the figure. A…

A: Given data: d1=0.90 ind2=0.80 ind3=1.25 inL1=11 ftL2=9 ftL3=5 ftE1=15200 ksiE2=28000 ksiE3=15200…

Q: The horizontal distance between its PVI and PVC is 150 meter. The elevation of PVI is 450.2 meter.…

A:

Q: 18 kN/m A 5.8m 17 m 22.7 kN/m со 10.6m 75 KN D Calculate the bending moment at B Calculate the…

A:

Q: Problem 1. A tape of standard length 20 m at 85°F was used to measure a base line. The measured…

A:

Q: Problem 4. Replace the three forces acting on the plate by a wrench. Specify the magnitude of the…

A: Given :

Q: 1.9 Briefly explain the procedure used by Eratosthenes in determining the Earth's circumference. 110…

A: (1.9) During the summer solstice, Eratosthenes measured the angle of the shadow at noon to be 7.2…