What are the Standard Sizes of doors and windows [used in AutoCAD] according on their: a.) usage b.) orientation and; c.) purpose

Q: . Solve for the slope and deflection at midspan using Conjugate Beam. 200 lb/ft M = 400 lb-ft B

A: A structure's first partial derivative of its internal energy is equal to the force applied at that…

Q: USING DOUBLE INTEGRATION, GET THE MAXIMUM DEFLECTION K₁=25/2 J 8/2 25 8/2 x R₂= 25/2

A: "Since you have posted multiple questions,  I will solve first for you as per guidelines"

Q: The bar in figure has a constant width of 30 mm and a thickness of 20 mm. Determine the maximum…

A:

Q: Appendix 1 shows a structural drawing of the first floor of a random building. The labels "C"…

A:

Q: : The lower sand layer sand layer in the soil profile of Figure 3a is in an artesian condition.…

A: Given;1 mg/m3 = 9.81 kn/m3

Q: 2. Please estimate the number of cycles to failure of a steel specimen under tensile fatigue loading…

A: Sm = 200 MPaSu = 560 MPa R value = 3

Q: 4) A plane truss is shown in the figure. 4-a) Determine "the degree of redundancy" (or "the degree…

A:

Q: Calculate the minimum cross sectional area (Amin) needed for a bar axially loaded in tension by…

A:

Q: 1) Use the method of joints to find the force in each member of the truss shown below in Fig 5.1…

A: Summation of horizontal force is 0.ΣFHori. = 0

Q: A rectangular channel carries a discharge of 5 m³/sThe channel is 2 m wide. What is the critical…

A:

Q: The total estimated duration of the mass excavation activities in an office building project is 40…

A: Duration of the project = 40 daysActivityTotal Volume to be excavated, yard3Unit priceActual Volume…

Q: A k 2 ft RR 100 lb/ft B 4 ft M = 1200 lb-ft E 1 ft 1 ft RE

A: Given overhanging beam with udl of intensity 100 lb/ft and moment,M = 1200 lb-ft.Given EI is twice…

Q: Sec. 9.1-9.4 9-1. Determine the reactions at the supports, then draw the moment diagram. El is…

A: Given data :

Q: If x = 4 m, y = 5 m, z = 3 m, P1 = 27 kN and P2 = 19 kN, determine the reactions at the base of the…

A: Dear student as per our company guidelines I'm solving the given frame by using a) portal method…

Q: Route the inflow hydrograph tabulated in the following

A: ##Calculate of outflow discharge of river by doing  flood routing by muskigham method ###

Q: A Coarse-Grained soil sample with N value of 14 can be identified as a Compact soil True False

A: Note - As per guideilines we are allowed to solve 1 question at a time in case of multiple…

Q: A sample of a saturated soil has a water content of 25%. If the specific gravity of soil solids is…

A: A saturated soil sample-Water content w=25%Specific gravity of the soil solids G=2.70Saturated soil,…

Q: 3-3 A rectangular section with width b=200mm and depth h=450mm is reinforc with 4 16 of HRB400. The…

A: Width (b) = 200 mmDepth (h) = 450 mmReinforcement of concrete = 4 -16 diameter HRB400Design Moment…

Q: 3. Determine the reactions and draw the shear and bending moment diagrams for the beam shown using…

A: The given information is as follows:  We have to find the following: Reaction of the beam Shear…

Q: A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.500 in., and each side…

A:

Q: What will be the ruling radius of a horizontal curve on a National Highway for a design vehicle…

A: A horizontal curve on a National Highway-Speed V=100 km/hour,Allowable super elevation…

Q: Given a crest vertical curve of length 523, with a PVC at elevation 1,016, connecting a grade 1% to…

A: The elevation of PVC = 1016The vertical curve consists of grades 1% and -0.5%The length of the curve…

Q: What is the K- design value for a roadway designed for 70 mph, and G₁=-2.5% and G₂=3.9%?

A: Design speed, V=70mph

Q: To make peg adjustment, the following notes were taken, WYE LEVEL AT 1 0.632 2.543 Rod reading at P…

A:

Q: Solve using Double Integration Method. Assume EI as stated in the picture. Step by step. Thank you .

A: Given overhanging beam with udl of intensity 100 lb/ft and moment, M = 1200 lb-ft.Given EI is twice…

Q: Classify: This sand has 61% predominately fine sand, 23% silty fines, and 16% fine subrounded gravel…

A: This sand has 61% predominately fine sand 23% silty fines 16% fine subrounded gravel size. The…

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…

A: ###Determination of members forces of truss using method of joint ###

Q: 2. Draw the shear and moment influence lines for points 1, 2, 3, 4, 5, 6 and 7. Then calculate the…

A: Given Propped cantilever beam subjected to moving load of 20 kNIt is asked to draw the Shear and…

Q: Q5/A reverse curve must be fit to the tangents shown below: PC1 P11 N 58-30′25 E S87 1045 E N47'5930…

A: Point Station:PC1= 21+83.05PI1 = 27+35.80PI2 = 38+43.05It is asked to determine the radii of the two…

Q: Problem 2.  A city requires a flow of 1.80 m3/sec  for its water supply. Compute the diameter of the…

A:

Q: The underpass sight distance design criteria only applies to crest vertical curves O True O False

A:

Q: What is the moment about point C caused by force F? The moment about D? (Answer needed for each…

A:

Q: Solve for the reactions at pin A and roller B in the structure below. 20 kips A 7777 15'-0" 15'-0"…

A:

Q: A straight wire 15 m long is subjected to tensile stress of 2000 kgf/cm². Elastic modulus is 1.5x106…

A: We have to calculate the temperature change to produce the same elongation

Q: A simply supported beam is subjected to a uniform service dead load of 1.5 kips/ft (including the…

A: Service dead load = 1.5 kips/ftService live load = 2.2 kips/ftConcentrated service dead load = 50…

Q: left alone.

A:

Q: Task 1 The engineering department has developed the following equation for the bending mom beam and…

A:

Q: Express the main and sub- classifications of crystal imperfections that you have studied.

A: Express the main and sub- classifications of crystal imperfections.

Q: A 500 mm square column is to be constructed above the ground. The vertical reinforcement consists of…

A: b = 500 mm h = 500 mmreinforcement = 8-28 mm barsMaximum size of aggregate = 25 mmfc = 20.7 MPafy =…

Q: Q.3) Determine the tensions in the three cables supporting a weight of 100 N as shown in figure…

A:

Q: For the soil profile shown in fig. top layer is sand. Initially the water table is 5m below ground…

A: Soil profile shown in figure,Initially the water table is 5 m below ground level, which is lowered…

Q: The true bearing of Tas observed from station A was 358° and magnetic bearing of the same was 8°. FD…

A:

Q: (ii) A very large and open reservoir discharges into atmosphere through a 100m long, 25 cm dia, f =…

A:

Q: Q2: Determine the moment at the fixed end (a). 3m 10 kN 3m 2 kN/m ob

A:

Q: F₁=250 N 300 A -2 r -3 m F₂ = 300 N 60° 4'm F3 = 500 N

A:

Q: 3) A parabolic cable is shown in the figure 3-a) Find xA  and  xB .  3-b) Determine the minimum…

A: L = 60 mEB=8 mTo find:a) Find xA  and  xB. b) Determine the minimum tension in the cable.c) Find the…

Q: Please solve asap!! The manhole cover of an ammonia storage tank is to be held by 25 stud bolts. If…

A: The number of bolts used to held the manhole cover = 25 stud boltsThe constant pressure inside the…

Q: Figure P3.58 1.89 emp 3.59 Water is siphoned from a tank as shown in Fig. P3.59. Deter- mine the…

A:

Q: Click to see additional instructions Determine the member forces in members AB, BD and AD? (Take…

A: Let us consider the method of joints to analyze the above truss.A free-body diagram of the truss is…

Q: For designing horizontal curves based on sight distance, the radius of the curve is designed to be…

A: For the safety of drivers, it is essential to consider proper sight distance when constructing…

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.