What determines the cut off point in performance of wind turbine

Q: Vapor turning directly to ice is called ____________. a. b. condensation b. d. glaciation…

A:

Q: ı dont understand

A:

Q: Process of forming metal powder by directing molten metal through an orifice after which it is break…

A: This question is based on the concept of manufacturing science.

Q: Let us assume that a gyroscope is on your desk now. How the direction of its axis will change with…

A: Gyroscope : It is a device which is well known for its ability to maintain the same axis of rotation…

Q: 213. The rigid bar AB, attached to two vertical rods as shown in Fig. P-213, is horizontal before…

A:

Q: iv. Calculate the force FBC in the member BC between node joints B and C. V. Calculate the force FAE…

A:

Q: For the air duct shown below, if the total pressure of air is 250 kPa and the static pressure is 50…

A:

Q: 3. Three bars each made from different materials are placed between walls when the temperature is…

A:

Q: Problem 1 50 kN 40 kN/m 50 kN 20 KN/m 200 kN-m 100 KN

A: given; lets take reaction force at D=RDAB=2mBC=4mCD=3mweight density (w1)=20KN/mweight density…

Q: The system of Fig.2 has three pendulums arrange as shown. Use Lagrange's equation to write the…

A:

Q: d) the thermal efficiency (%) of the cycle. e) Sketch the cycle on a T-s diagram, showing all…

A:

Q: An adiabatic rigid steam tank has expansion valve. Initially, steam is at 1MPa and 350C. Suddenly,…

A:

Q: A simple truss is subjected to 20 kN force at point A as shown in Figure 2. The reaction force at…

A:

Q: The rigid bar of negligible weight is supported as shown in the figure. If W = 80 kN, compute the…

A:

Q: Determine the hoop stress on the outer surface of the cylinder.

A:

Q: What thrust is obtained from a propeller 3 m in diameter that has the characteristics given in Fig.…

A:

Q: 1) A cup-drawing operation is performed in which: The cup's inside diameter = 75 mm and its height =…

A: Given Datad=75mmh=50mmt=3mmRd=4mmσt=400MPa

Q: * liquid limit should always be greater than plastic limit True O False O * Gs is a unitless value…

A: True   Liquid limit should always greater than plastic limit As, liquid limit - plastic limit =…

Q: what table and column are you looking at to get 103 kj for the enthalpy , and how are you getting…

A:

Q: A torque T = 1500 N − m is applied to the hollow shaft shown that has a uniform 10 mm wall…

A: find the shear stress at a and b and angle of twist.

Q: F4-8. Determine the resultant moment produced by the forces about point O. 0Ahi Ja ll ll la l F =…

A:

Q: 1. Status comes under which of the following types of barriers? A Semantic barrier B. Organisational…

A:

Q: .Determine the moment of the 1800-N force about (a) point C and (b) point B of the engine hoist…

A: Calculate Moment of 1800N about C and B

Q: (i) An ideal gas at a given state expands to a fixed final volume first at constant pressure and…

A:

Q: 10. Gas from a bottle of compressed helium is used to inflate an inelastic flexible balloon,…

A: Work done by the balloon on the atmosphere,w=p*∆v P=760mmof Hg=1atm=1.01*10^5 Pa…

Q: A sand casting mold is shown. All bottom and side plates have a uniform thickness of 1". The bottom…

A: Given : To find : Design a cylinder

Q: standard reference of water content determination is ASTM D 2216

A: we have to determine the ASTM standard for determination of moisture content in soil

Q: A steel bar AD has a cross-secțional area of 260 mm? and is loaded by forces P, = 12 kN, P, = 8 kN,…

A: Given data P1 = 12 kNP2 = 8 kNP3 = 6 kNa = 1.5 mb = 0.6 mc = 0.9 mE= 210 GPa

Q: Design a highpass filter with a high-frequency gain of 5 and a corner frequency of 2 kHz. Use a…

A:

Q: For the given beam with shown loading, determine the reaction at the roller support. 30 kips/ft C -2…

A:

Q: Calculate the 2nd moment of area for a beam with a length of 200 mm, a width of 20 mm and a height…

A:

Q: The internal pressure of a 400 mm inside diameter cylindrical tank is 10 MPa and the wall thickness…

A:

Q: А cube with an edge of 2·5 cm as shown in Fig. 1.4 was tested in compression. Under a load of 400 kN…

A: In compression, we examined a cube with a 2.5 cm edge, as illustrated in the picture. It failed…

Q: y 5 m 5 m A 5 m В 20 kN

A:

Q: Evaluate the given integral. dx 1+e2x

A:

Q: Atomization, electrolytic deposition and reduction methods are used to produce metal Powders

A: This question is based on the concept of metal powder production.

Q: 3-20.For the system shown in Figure P3-20 determine the moment about (a) point A and (b) point B. 8…

A:

Q: I got a solution for this, question is how does he got 2.05 in Kt?

A:

Q: 22. Verify that the motion defined by the velocity components v, = 3x3, vz = -4x,, vz = 4x2 - 3x, is…

A:

Q: It is known that the average annual wind speed in 1997 was 2,205 m/s with a mass density of 1.17…

A:

Q: Determine the thickness of a steel air receiver with  30 inches diameter and pressure load of 120…

A: Given,  Steel Air Reservoir Inner Diameter = Di= 30 in Pressure = P= 120 psi Design stress= S= 8000…

Q: What are the work and energy equations ?

A: Work and energy both are dynamic forms of energy.

Q: A uniform rod AB of mass m = 6.4kg is welded at its midpoint G to a vertical Shaft GD. Knowing that…

A:

Q: 20. A small hole in a 50 kg sack of rice causes some rice to be wasted while the sack is lifted…

A:

Q: 1. A 60-mm-radius drum is rigidly attached to a 100-mm-radius drum as shown. One of the drums rolls…

A:

Q: A direct extrusion process is used to reduce a cylindrical part that has a diameter of 5 inch and is…

A:

Q: Orthogonal cutting is dimensional metal cutting

A: Orthogonal cutting is ____________ dimensional metal cutting. Answer: a. two

Q: Process of forming metal powder by directing molten metal through an orifice after which it is break…

A: Process of forming metal powder by directing molten metal through an orifice after which it is break…

Q: A compound steel (G = 70 GPa) shaft consists of a solid 59-mm-diameter segment (1) and a solid…

A:

Q: A gusset plate is subjected to the forces shown in the figure below. Find the magnitude (F) And…

A: