1) A cup-drawing operation is performed in which:The cup's inside diameter = 75 mm and its height = 50 mm.%3DStock thickness = 3.0 mm.%3DPunch and die radii = 4 mm. Tensile strength = 400 MPa for this sheet metal.%3D(a) Find the required starting blank size(b) Is this drawing operation feasible?(c) Determine the drawing force, and(d) Determine the blank-holder force.

Given Datad=75mmh=50mmt=3mmRd=4mmσt=400MPa

1) A cup-drawing operation is performed in which: The cup's inside diameter = 75 mm and its height = 50 mm. Stock thickness = 3.0 mm. Punch and die radii = 4 mm. Tensile strength = 400 MPa for this sheet metal. (a) Find the required starting blank size (b) Is this drawing operation feasible? (c) Determine the drawing force, and (d) Determine the blank-holder force.

1) A cup-drawing operation is performed in which: The cup's inside diameter = 75 mm and its height = 50 mm. Stock thickness = 3.0 mm. Punch and die radii = 4 mm. Tensile strength = 400 MPa for this sheet metal. (a) Find the required starting blank size (b) Is this drawing operation feasible? (c) Determine the drawing force, and (d) Determine the blank-holder force.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question: 2 a. Distinguish between roll bending and roll forming.b. What are some of the simple measures used to assess the feasibility of a proposed cup drawingoperation?c. Compare spinning over the press work for sheet metal products.d. Identify a major technical problem in tube bending.
A drawing operation is used to form a cylindrical cup with inside diameter of 75 mm and height of 50 mm. The starting blank size is 140 mm and the stock thickness is 2.4 mm. Based on the data, is the operation feasible?
1. A component is designed to be hot forged in an impression die. The projected area of the product is 5800 mm2. During the forging process flashing is formed so that the area including the flash will be 8900 mm2. The part geometry is considered to be simple and the heated work material yields at 92 MPa. Calculate the maximum force required to perform the operation. 2. What are the advantages and disadvantages to forge a product through the open forging process, rather than to machine it from the same material?
In a wire drawing operation diameter of a steel wire is reduced from 10 mm to 8 mm. The mean flow stress of the material is 400 MPa.what is the ideal force required for drawing (ignoring friction and redundant work).?
What are the advantages of a counterblow or impact forging machine? What are some of the properties desired in forging dies?
1. A round wire made from 1020 carbon steel is being drawn from a diameter of 12.5 mm to 9.5 mm in a draw die of 10°. For a coefficient of friction of 0.15, calculate required drawing force. 2. How would the extrusion process be effected if the die angle is increased?
Q#3:(b) Explain the differences between Forward Extrusion and Reverse Extrusion processes
Q#4:(a) Explainthe advantage of corner radii of punch and die in Sheet Metal Drawing Process.
Both extrusion and bar drawing processes can be used to reduce the cross section. What can be the basic differences between extrusion and bar drawing processes? Also discuss briefly why must the drawing stress never exceed the yield strength of the work metal?
Explain the function of backing rolls in Four High Rolling Mill and Cluster Rolling Mill. please explain
Write a detail note on direct extrusion process.
A cylindrical billet that is 100 mm long and 50 mm in diameter is reduced by indirect (backward) extrusion to a 20 mm diameter. The die angle is 90°. In the Johnson equation, a = 0.8 and b = 1.4. In the flow curve for the work metal, the strength coefficient = 800 MPa and strain hardening exponent = 0.13. Determine (a) extrusion ratio, (b) true strain (homogeneous deformation), (c) extrusion strain, (d) ram pressure, and (e) ram force