What is maximum deformation?

Q: What is elongation testing?

A: Elongation testing is a measure of far stretching of a sample before it breaks. The result is…

Q: The mode of deformation of the metal during spinning is (a) Bending (b) Stretching (c) Rolling and…

A: Given Data⇒Mode of deformationmetalSpinningProblem definition⇒Problem says choose the correct…

Q: What exactly is meant by the term "shearing stress"?

A:

Q: 9) Define the rolling resistance. 10) Define the slip angle.

A: Rolling Resistance It is the resistance offered by the body when it rolls on the ground or it is…

Q: What thickness limit classifies metal as being sheet?

A:

Q: What is the discontinuity of loading?

A: The load along the length of the structure, say a beam if is consistent then we can say that the…

Q: How can we determine the deformation of an axially loaded member?

A: Whenever a member is loaded axially there is change in the dimensions of the member. Length of the…

Q: What is impact loading?

A: Impact loading is a type of loading whose period of action is very less. Generally, when the time of…

Q: What are conservative forces?

A: Conservative force: When the work done by the force on a body does not depend on the path of the…

Q: How is shear obtained?

A: Shear stress developed in material obtains from the applied force on the material and the…

Q: What does shear strains cause?

A: Answer Shear Strain : it is the angular displacement from the original position

Q: What is the effect of an eccentric loading?

A: Eccentric loading: The eccentric loading is a type of loading on beams and columns in which load…

Q: Which of the following statement(s) is/are correct? i. Necking or localized deformation begins at

A: Explanation: Necking : Necking is localized deformation which is begins at maximum load in the small…

Q: Describe the State of Stress caused by the combined loadings?

A: Combined loading: In combined loading conditions,  the specimen/ component is subjected to various…

Q: What is period of deformation?

A: The period of deformation can be defined as

Q: 1. List the seven types of failure 2.Define die penetrant test 3.Suggest N.D.T.test for an internal…

A: subject : Material Science

Q: What are non conservative force?

A: Non conservative forces are those forces ,which if act, there is loss of mechanical energy of a…

Q: Rank the curves based on the change in strain that occurs during the necking phase. Rank the curves…

A: Various stages shown on the stress-strain diagram are: Proportionality limit Plastic limit Necking…

Q: How does point defect affects the property of a material?

A: To find : How does point defect affects the property of a material

Q: What is the permanent strain?

A: Strain: When a force is applied to any system, they deform based on the applied force. The…

Q: Draw shear force and bending momenE

A:

Q: What do the normal strains cause?

A:

Q: What happens to the shear stress as flexural capacity increases?

A: It is the strength of any beam against transverse loads applied on them. It is given by 'EI', where…

Q: How was the shear formula derived?

A: Shear Stress: This is the ratio of force acting per unit area of an object/component.  This is…

Q: What is the permanent deformation?

A:

Q: Why is the allowable shear stress checked?

A: Stress which is induced in a material due to the tangential forces, is termed as shear stress. This…

Q: What happens If the material is subjected to triaxial stress?

A: Triaxial stresses are those in which three mutually perpendicular normal stresses acts as shown in…

Q: Define deformation process

A: Deformation process is the secondary manufacturing process.

Q: How is the shear center determined?

A: Shear Center The shear center is a point on the section of the beam, from where the resultant load…

Q: Describe four (4) common forging defects

A: GIVEN SUBJECT- MATERIAL SCIENCE             TOPIC  - FORGING REQUIRED EXPLANATION ABOUT  four (4)…

Q: Explain Flexure Test of Small, Clear Specimen (ASTM D143) ?

A: ASTM D143  consists of the "Standard Test Methods" for Small and  Clear Specimens of Timber/wood. It…

Q: What is the true sliding strain for a low carbon steel bar which is doubled

A: Given:Low carbon steel

Q: What is the procedure to apply the shear formula?

A: What is the procedure to apply the shear formula?

Q: Which material is stronger? 250 maraging steel at room temperature (RT) or 6061 T6 aluminum sheet at…

A: Aluminium is around one-third the weight of stainless steel, which is why it's employed in…

Q: What is the equivalent stiffness?

A:

Q: responsible for residual deformation?

A: Solution :-  Answer:- option a ( residual plastic strains)

Q: Stress and strain: What are they and why are they used instead of load and deformation?

A:

Q: How did temperature affect the toughness of the specimens?

A: temperature affecting the strengths of the toughness . IMPACT TOUGHNESS        Toughness is the area…

Q: What is Residual Stress?

A: Whenever a body is deformed beyond the elastic limit it is unable to regain its initial shape. Due…

Q: What 3 types of loading may lead to failure?

A: There are various ways by which a material may lead to failure. For instance, in case of mechanical…

Q: what effects does bending have on material properties

A: What is bending? It is defined as the state of stress.

Q: Discussions Why is a minimum thickness of at least ten times the depth of the impression required in…

A: Given: Discussions Why is a minimum thickness of at least ten times the depth of the impression…

Q: What is the Shear Formula?

A: When the shear force is applied on the body then in that case the shear stress is acted upon the…

Q: What is the longitudinal elongation?

A: When an object is subjected to load P then in that case it elongates in X direction and while…

Q: 7. What is meant by eccentric loading and eccentricity?

A: What is meant by eccentric loading and eccentricity

Q: Which deformation is stay after removing of external load ?

A: Given Data⇒External LoaddeformationProblem definition⇒Problem says determine which deformation stays…

Q: What are the Linear distributed loadings and how does it produce reluctant force?

A: The loadings in which the load is not acting at one point but is spread over some length is known as…

Q: Which would normally have the highest percentage elongation at break, 0.1% carbon steel or aluminium…

A:

Q: what is the equation and units for finding yield stress?

A:

Q: What is internal force?

A: Generally, Internal forces are generated due to external forces in the materials which is under…

Q: What are the benefits of performing the tension test?a

A: given:   What are the benefits of performing the tension test?

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.