Describe the State of Stress caused by the combined loadings?

Q: What is the relationship between the ?distance from neutral axis and stress

A: The stress, s, in the element a distance, y, from the neutral axis i s proportional to the…

Q: Give an example of the complicated stress distribution?

A: When any material is subjected to external load then stresses are induced in the material. These…

Q: What is Circumferential Stress?

A: Circumferential Stress When pressure inside thin pressure vessel exceeds it exerts force from inside…

Q: Sketch the relationship between the stress and the number of cyclic loading applied on an element

A:

Q: How can we determine the deformation of an axially loaded member?

A: Whenever a member is loaded axially there is change in the dimensions of the member. Length of the…

Q: How does torsional stress and angle of twist impact engineering design?

A: Importance of torsional stress in Engineering Design:- Torsional stress is induced in an element due…

Q: 5-in stress strain curve the engineering stress will decrease after the tensile strength point?

A: Given data  To draw the stress strain diagram.

Q: Define about the Selection of Shear Strength Parameters ?

A: Stability analysis of a rock slope requires an assessment of shear strength parameters, that is,…

Q: Part 2 As the area under the stress-strain curve decreases, the toughness___________.   stays the…

A: Toughness: The capacity to absorb the energy of the material before the failure is known as…

Q: What is the effect of an eccentric loading?

A: Eccentric loading: The eccentric loading is a type of loading on beams and columns in which load…

Q: Give an example of the single shear failure?

A: Shear is caused by the action of two opposite and equal forces acting on a material. If the two…

Q: What is the biaxial stress?

A: Biaxial stress can be explained as when stresses are acting on an element in X and Y direction, and…

Q: Define the term Uniaxial stress?

A: When the stress is generated due to loading in one direction (along the axis of the loaded member),…

Q: explain linear stress variations,

A: As per Hooke's law in any material the stress induced is directly proportional to…

Q: Determine average yield stress in this operation.

A: Given; An annealed copper wire of 25 mm diameter is drawn into a wire of 5 mm diameter. Data is…

Q: Describe the impact loading?

A: It is a kind of loading where the load is applied for a very small amount of time. In this loading,…

Q: What type of stress is referred to as Ultimate Stress?

A: When a specimen is loaded axially with tension, it elongates. There is a point up to which if the…

Q: What is the tensile stress?

A: When there is loading over a member in the direction of its axis, then stress produced under such…

Q: What is yield stress?

A: Yield Stress:  It is the amount of stress at the yield point of a material/component. The yield…

Q: Characterize the general state of stress at a point?

A: The general state of stress at a point can be characterized in the following way: 1.Three…

Q: Discuss the effects of applying a torsional loading to a long straight member?

A: Torsional Loading causes the deformation of the straight member about its longitudinal axis. It is…

Q: . What is the longitudinal stress developed in

A: To find Longitudinal stress

Q: points on the stress-strain curve for medium-carbon ste

A:

Q: What is Ultimate stress?

A: Ultimate Stress The ultimate stress recognizes as the maximum value of stress that a material can…

Q: What are principal stresses?

A: The highest and the lowest value of the normal stress acting at a point is known as the principal…

Q: 5-In stress strain curve the engineering stress will decrease after the tensile strength point?

A: To give proper explanation of the above statement.

Q: What is maximum deformation?

A: Given Deformation To find Maximum deformation

Q: What is the true sliding strain for a low carbon steel bar which is doubled

A: Given:Low carbon steel

Q: What is the linear variation in shear stress along any radial line?

A: For a linear-elastic material, the shear stress varies linearly with shear strain.

Q: What is the general state of Stress?

A: The general state of stress at a point is 3 normal stress and 6 shear stress.

Q: Determine the ultimate tensile and compressive stresses?

A: Ultimate compressive stress             The maximum amount of compressive stress that a material…

Q: Describe Bending Stress

A: Bending stress is the normal stress that an object encounters when it is subjected to a large load…

Q: Describe shear stress?

A: Shear stress When a body undergoes a load and deformation is caused by the stress that is parallel…

Q: With what is Stress associated and how?

A: Please Specify the question in more detail, sir.   But in general, it can…

Q: A typical value for the yield stress of mild steel would be? Select one: O a. 200 GPa O b. 100 MPa O…

A: Option c is correct.

Q: Define the term bending stress?

A: The bending stress is the normal stress acting on a body when the body is subjected to a large load…

Q: What is compressive principal stress?

A: In the three principal stresses , it is mentioned in the diagram as  σ1, σ2 and σ3. σ1 is maximum…

Q: Why is the magnitude and direction of the principal stress change from point to point within a beam…

A: Principal stresses is known as the magnitude of normal stress  acting on a principal plane in a…

Q: responsible for residual deformation?

A: Solution :-  Answer:- option a ( residual plastic strains)

Q: What is required to relate the stress distribution to the resultant bending moment?

A: The restoring force per unit area which is equal in magnitude of the applied force but in opposite…

Q: When does the plane stress occur?

A: Plane stress is defined as the state of a material when one of the stress components are acting on…

Q: Define Tensile strength.

A: Given Data⇒ Tensile strength Problem statement⇒ Problem says Define Tensile strength.

Q: why specific rigidity is needed?

A: Specific rigidity is defined by the ratio of young's modulas to the density. The more accurate term…

Q: How can the stress coordinates of the points on the curves be determined?

A: To explain  How can the stress coordinates of the points on the curves be determined? Concept used…

Q: When an elastic material is subjected to normal stress, what would thestrains that are produced…

A: The strain is the response of a system to applied stress. When a material is loaded with a…

Q: 1. Specify a suitable aluminum casting alloy for a bar with square cross- section. Length of one…

A:

Q: What is the Average normal stress?

A: Average Normal Stress⇒average normal stress can be defined as the average normal stress acting in X…

Q: What is Normal Stress?

A: Normal Stress: When the stress is acting in the direction perpendicular to the body then it is said…

Q: what is the equation and units for finding yield stress?

A:

Q: between direct stress and bending stress.

A: To define: Distinguish between direct stress and bending stress