What is the contents of the stack after executing the instruction marked by for the first time .org 0x00 LDI R16, HIGH(RAMEND) OUT SPH, R16 LDI R16, LOW(RAMEND) OUT SPL, R16 LDI R17, 0 CALL L1 CALL L2 CALL L3 HERE: JMP HERE .org 0x100 L1: INC R17 CALL L2 INC R17 RET .org 0x200 L2: INC R17 * CALL L3 INC R17 RET .org 0x300 L3: INC R17 RET

Q: What is the contents of the stack after executing the instruction marked by * for the second time…

A: a.) For the program in the LOOP, First the instruction "SBI PORTD, 0" will set the first pin of PORT…

Q: What is the contents of the stack after executing the instruction marked by * for the second time…

A: Hey there, I am writing the required solution based on the above given question. Please do find the…

Q: After execution the near process call instruction CALL AAOOH, the last values store in top of stack…

A: ANSWER 1: 00AAh Explanation: Considered as a straight information design, or all the more…

Q: in  80886 microprocessor What is result of executing the following instruction sequence? MOV BX,…

A: MOV BX, 100H will load 100 to register BX, MOV [ BX], 0C0ABH   the address of BX is now 0C0ABh MOV…

Q: B- What is the content of the stack register after execute the following instruction (Assuming each…

A: Stack  Stack is a linear data structure that follows a particular order in which the operations are…

Q: Suppose during an execution of an instruction, the Stack Pointer register had the value 000Ah. After…

A: Actually, An interrupt is a signal informing a program that an particular event has occurred. It…

Q: Following the x86-64 calling conventions, any arguments past the 6th have to be stored on the Stack.…

A: Below i have written code instruction for coppy

Q: 3- Let a program have a portion fr of its code enhanced to run 4 times faster, to yield a system…

A: In this question, we are given enhanced speedup(SE) and overall speedup of system. And we are asked…

Q: In some instruction sets, call and return instructions make use of a RR register to hold the return…

A: A link register is a special-purpose register which holds the address to return to when a function…

Q: 6- what segmevd vegisler may wot be popped from the stack -7- Explain what happens when the PUSH AX…

A: 6.  Pop instruction loads the values from stack  into general-purpose register, memory location,…

Q: Write and assemble a program to: a) Set SP to address 0x200 (same technique as we used with RAMEND,…

A: .INCLUDE "M32DEF.INC" LDI R20, HIGH($9D) OUT SPH, R20 LDI R20, LOW($9D) OUT SPL, R20

Q: Very urgently needed!!   Suppose before the CALL instruction within a code the registers has…

A: The Answer is

Q: Loading a piece of data from memory into the CPU's register, all instructions must be fetched before…

A: Correct Option is (c)- PA=AABCFH Solution is given below:

Q: Loading a piece of data from memory into the CPU's register, all instructions must be fetched before…

A: Here is the answer with an explanation:-

Q: Write down the values of destination operands and flags after the execution of each instruction:…

A: mov cx, 1 sub cx, 1; a) CX = 0, ZF = 1 mov cx, 0 sub cx, 1; b) CX = -1, SF = 1 mov al, 0FFh add al,…

Q: Given the typical stack frame set up, what will be in edx after executing this instruction: nov edx,…

A: Stack frames are the foundation of stack memory. In the stack frame the lower memory addresses are…

Q: Question 3 Suppose during an execution of an instruction, the Stack Pointer register had the value…

A: a) The Value Of the Flag Register is Pressed. It means that first the value of the Stack Pointer is…

Q: Q2/ The following program have been executed by an 8085 Microprocessor. Write down the sequence of…

A: Let see the solution below.

Q: 3. Answer all the questions given below. (a) Consider LIFO and FIFO algorithm as below, [CO2] LIFO…

A: The answer is  given below:-

Q: Assume that we would like to replace the ISZ instruction in the Basic Computer with a new…

A: Here we need to complete the sequence below of micro-operations that are necessary D6T4 : ____…

Q: Instead of $t1 having the value of x as in previous question, suppose $a0 contains the memory…

A: In above question we find that,what instruction should be used to load the value to $t1.

Q: n  80886 microprocessor What is result of executing the following instruction sequence? MOV BX,…

A: MOV BX, 100H   will store the value 100h in register BX. so, BX = 0100h MOV [ BX], 0C0ABH   The…

Q: Question 2: Consider the following assembly language program and show the stack pointer and register…

A: Because EQU 0F000H therefore stack pointer starts with an address < 0F000H. Initial stack pointer…

Q: Copy the top 2 words from the stack into registers AX and CX respectively. Do this without changing…

A: Below i have answered:

Q: 1. a) What is the size (in bits) of the Stack Pointer in 8051? b) With each PUSH instruction, the…

A: Answer: a) Size of Stack pointer in 8051 is  8-bits wide, and it may take a value of 00 to FFH. When…

Q: What is the main difference between the JMP instruction and the JSRR instruction? O There is no…

A: JMP is used to perform the unconditional jump - to the address specified operand. as an example, JMP…

Q: CS=3000H, DS=5000H, ES=7000H, SS=9000H, IP=0123H, SP=1234H, BP=5678H, SI=8765H, DI=4321H. If ZF=1,…

A: ANSWER :-

Q: A programmer has written Assembly Language Program (ALP) using 8086 instruction set. The program…

A:

Q: Explain the Register stack organization of 32 locations of the stack (0 to 31 ). take the initial…

A: SUMMARY: -Hence, we discussed all the points.

Q: Given the instruction format of X86 processor and codes for internal registers below REG & R/M…

A: Given the instruction format of X86 processor and codes for internal register given in above figure.

Q: Assume that we would like to replace the ISZ instruction in the Basic Computer with a new…

A: (1): DSN (2): AC, 0 (3): DR (4): AC

Q: 12. The ret instruction modifies the A. base register B. bp register C. flags register D.…

A: We know that there is nothing you can directly inject into the instruction pointer that will cause a…

Q: Pipelining in 8086 processors is achieved using which of the following option: O a. By using the…

A: Here have to determine correct option for 8086 pipeline.

Q: 2- Draw memory and microprocessor contents before and after execution the following instruction: MOV…

A: Given: We are given a microprocessor instruction below: Goal: We have to find the contents of…

Q: Pipelining in 8086 processors is achieved using which of the following option: a. By using the…

A: Answer is d) By using the 6-byte instruction queue that stores pre-fetched instructions while one…

Q: A program stack is to use 800 h bytes and SS= 0300 h, A = 1234 h and B = 6AB3 h. Shows the contents…

A: A program stack is to use 800 h bytes and SS= 0300 h, A = 1234 h and B = 6AB3 h. Shows the contents…

Q: What will be the values stored in registers r1 and r0 after the execution of the instruction mul…

A: Here is the answer with an explanation:-

Q: 2- Draw memory and microprocessor contents before and after execution the following instruction: MOV…

A: Given: We are given a microprocessor instruction that is executing.  Goal: We have to find out…

Q: Hi there, I'm looking for some help with this MIPS code. I'm trying to see why the code is…

A: Your written code might not be optimal because you are using extra registers.  move $t8,$s0 moving…

Q: 10. Consider the following code:  .386 .model flat, stdcall .stack 4096 ExitProcess PROTO,…

A: the solution is given below :

Q: What is the result produced in AX by executing the following instruction sequence? * MOV CL, 34H MOV…

A: Given Data : Input to the register CL -> 34H Input to the register AL -> 12H

Q: Q3. If content of AX register is OXFEDC, BX is Ox9876 and CF = 1 respectively, Find contents-of AX…

A: This question is related to 8086 microprocessor. So, given three instructions SBB, MUL, XOR, that…

Q: Explain the Memory stack organization of 16 locations of stack( 0 to 15). take the initial value of…

A: Given:   the Memory stack organization of 16 locations of stack( 0 to 15). The initial value is SP =…

Q: Explain the Memory stack organization of 16 locations of stack( 0 to 15). take the initial value of…

A: Answer: I have given answered in simple how to perform push and pop operation in Memory stack…

Q: 1. For the following C code, what are the corresponding MIPS (Microprocessor without Interlocked…

A: The answer is

Q: Q4) Write the assembly language instructions required to find the 2's complement of 30 numbers, each…

A: In this case 2's compliment 1 bit is used for sign bit The maximum integer=223 -1, 0X03 stack…

Q: Q4) Write the assembly language instructions required to find the 2's complement of 30 numbers, each…

A: In this case 2's compliment 1 bit is used for sign bit The maximum integer=223-1, 0X03 stack segment…

Q: 6) After the execution the far jump instruction JMP B3000123H, the new value of Physical Address…

A: In the given question we use simple concept of physical address:…

Q: Q4) Write the assembly language instructions required to find the 2's complement of 30 numbers, each…

A: The basic code for doing the conversion of negative to positive numbers in assembly

Q: Q4) Write the assembly language instructions required to find the 2's complement of 30 numbers, each…

A: In this case 2's compliment 1 bit is used for sign bit The maximum integer=223-1, 0X03 stack segment…