Question 3 Suppose during an execution of an instruction, the Stack Pointer register had the value 000Bh. After that an interrupt occurred . the interrupt after completing mandatory procedures. The Interrupt Vector (IV) of an Interrupt Service Routine (ISR) is C89A3H. this IV is C021h and segment address is stored in the memory location 00066h and 00067h. (Must show all calculations) a. What is the value of SP when the ISR is being serviced? b. What is the value of IP/Offset? c. What is the Interrupt Type?

Question 3 Suppose during an execution of an instruction, the Stack Pointer register had the value 000Bh. After that an interrupt occurred . the interrupt after completing mandatory procedures. The Interrupt Vector (IV) of an Interrupt Service Routine (ISR) is C89A3H. this IV is C021h and segment address is stored in the memory location 00066h and 00067h. (Must show all calculations) a. What is the value of SP when the ISR is being serviced? b. What is the value of IP/Offset? c. What is the Interrupt Type?

Computer Networking: A Top-Down Approach (7th Edition)

7th Edition

ISBN:9780133594140

Author:James Kurose, Keith Ross

Publisher:James Kurose, Keith Ross

Chapter1: Computer Networks And The Internet

Section: Chapter Questions

Problem R1RQ: What is the difference between a host and an end system? List several different types of end...

See similar textbooks

Related questions

Q: 6. Suppose that the interrupt processing method of is to store the breakpoint in the address of…

A: Input yield gadget gives the intrudes. The Processor completes the execution of a guidance prior to…

Q: Problem 1: Highlight the data path that is active during the execution of the following MIPS…

A: Actually , the answer has given below:

Q: Problem 1: Highlight the data path that is active during the execution of the following MIPS…

A: Actually, the answer has given below:

Q: Th is exercise is intended to help you understand the relationship between forwarding, hazard…

A: A) Insertion of NOPs to avoid hazards: In the given mips code, nops are inserted to avoid hazards…

Q: a) Generate a full RTN code in Fetch, Decode, Execute and Write Back step for: MUL 602, #5, #2…

A: The answer is

Q: 19. The 8085 microprocessor respond to the presence of an interrupt a. As soon as the trap pin…

A: Question 19. The 8085 microprocessor respond to the presence of an interrupt a. As soon as the trap…

Q: Assume that an interrupt mechanism uses the hardware stack to store PC and other registers of the…

A: An interrupt is the automatic transfer of software execution in response to a hardware event…

Q: Evaluate the effect of the instruction LDR r1, [r2], #4, given the initial values below. What is the…

A: As ldr r1,[r2], #4 means r1= mem[r2] this means r1=mem[1004] so r1=20 r2 = 1004+4 r2=1008 r3=50…

Q: Consider the following code fragment. What are the contents of the eax, ebx and ecx registers after…

A: Registers are impermanent capacity areas inside the CPU that hold information and addresses. The…

Q: Problem #11 Consider the PIC24 assembly instruction given by: mov f, WREG n your own words: What is…

A: ANSWER:-

Q: For the following C++ statement, what is the corresponding MIPS assembly code? Assume that the C++…

A: Given :- f = g + (h - 5) Assume :- f = $s0 g = $s1 h = $s2

Q: Consider the diagram below that shows the fetching data flow for an indirect cycle along with the…

A: What will be the content of the MAR register after finishing the execution of the indirect cycle for…

Q: Assume that an interrupt mechanism uses the hardware stack to store PC and other registers of the…

A: Interrupts: these are the signals which will be sent to the central processing unit by the…

Q: Following is the memory map beginning from address 3C00H and increasing addresses to the right, all…

A: These instructions are used to transfer the data from the source operand to the destination operand.…

Q: (a) An instruction at address 021 in the basic computer has I=0, an operation code of the AND…

A: Answer

Q: Problem 2.3: The following have bcen executed by an 8085 Microprocessor. Write down the sequence of…

Q: (a) Suppose that a processor executes instructions each of which is 16-bits long. How many different…

A: Given: Each instruction is 16 bits long find how much different instruction repertoires of this…

Q: he following diagram shows some registers like processor registers R1 and R2, Program counter PC and…

A: Given : Memory layout Instruction format Address field 1 = 200 Address field 2 = 300

Q: An instruction in address (021)16 in the simple machine has a mode bit I = 0, an operation code of…

A: Actually, given information An instruction in address (021)16 in the simple machine has a mode bit…

Q: 1. For the following C code, what are the corresponding MIPS (Microprocessor without Interlocked…

A: The answer is

Q: ermine the specific type of addressing mode (SMALL LETTERS only) and compute for the address/es. If…

A: It is defined as the method to specify the operand of an instruction. The job of a microprocessor is…

Q: Write necessary instructions to assign the following registers to the corresponding locations in…

A: Below i have provided the instruction for the problem in assembly language.

Q: Q41 (a) Generate a full RTN code in Fetch, Decode, Execute and Write Back step for: MUL 602, #5, #2…

A: The answer is

Q: 3.On the PDP-8, only memory on the current page or on page zero can be addressed directly in a…

A: The PDP-8 (Programmed Data Processor) :- PDP-8 (Programmed Data Processor) was a 12-bit…

Q: Treat the registers R1, ..., R7, the program counter PC, and the condition-codes N, z, P as…

A: Answer: 1).IINSTRUCTION :0001010110000111. Hex number :EB 2F3F 6BEF Hex signed 2 complements: 0000…

Q: Suppose we have the instruction Load 1000. Given memory and register R1 contain values below: Memory…

A: Question from Adressing modes. And we have a Load instruction: LOAD 1000 Meaning of instruction is:…

Q: Let us consider a memory that includes two instructions. First instruction is located at memors…

A: It can be approached as: The instruction consists of opcode and operands. Given the instruction…

Q: A relative mode branch type of instruction is stored in memory at an address equivalent to decimal…

A: Relative addressing mode: The PC relative addressing mode is used to load a register with a value…

Q: Answer the following questions. A. A computer system has a main memory access time as 60ns. you as a…

A: ANSWER:-