What is the counterclockwise angle?

Q: Expandable pattern is used in ?

A:

Q: What is the Torsion formula?

A: The expression of torsion equation is given by, Here, T is the twisting torque, J is the polar…

Q: t is the figure called? explain and elaborate

A: The apparatus is a open cup flash point test apparatus

Q: What is the internal axial force?

A: Internal Axial Force is defined as the force acting in the direction parallel to the axis of the…

Q: what is the measured distance to the nearest eigthth between the outside corners of the tongue and…

A: FRAMING SQUARE  A framing square, also known as a steel or carpenter square, can be the most…

Q: -rce. What is the best angle?

A: To find angle.

Q: what is the length of the red line?

A: Solution:

Q: 1- What type of drawing is this (Assembly, detail assembly, detail, pictorial)? And What is the…

A: Given Drafting To find Type of drawing Angle of projection Scale of drawing Original length of shaft…

Q: Where did the 107.11 came from

A: Given   Weight, W1 = 500 N                 W2 = 1000 N Find   The angle 107.11o

Q: Discuss how the Cylindrical Square is used.

A: A cylinder square is used for checking the squareness of vertical axis with reference to horizontal…

Q: The cord of a bow string drill was used for

A: The bow drill was used in ancient period.

Q: Describe thrust angle.

A: Introduction  The thrust angle is basically used as a major angle for alignment of the rear and…

Q: if the f Re 20 -0.25 mm %3D De terminef?

A: Relative roughness, eD=0.25Reynolds number, Re=20

Q: Define the following commands. a) Extrude b) Revolve c) Sweep d) Blend e) Pattern

A: Extrude : Extrude command creates a 3d solid object from a base which can be a closed polygon,…

Q: What is the symmetrical axis?

A: Axis of symmetric.  Axis of Symmetry is a line that Split the figure into two symmetrical sections…

Q: What is the lowest allowable dimension for the flats?

A: Solution:

Q: B. What is the difference between the critical point and triple point? explain with drawing.

A: GIVEN DATA - TRIPLE POINT AND CRITICAL POINT GIVEN WE HAVE TO EXPLAIN IT WITH DRAWING

Q: inorder to accomplish a desired angle, A sin bar is used with

A: Slip block gauges

Q: Draw the front, Top , and side planes for a complete cut *Note the shape is symmetrical

A: a. Front b. Side c. Top

Q: . Circle the correct section view out of the three possibilities. Would a half section been…

A: The section 2 is correct. The reason is mentioned below. First look at the cutting plane, it is…

Q: What is the percentage of rods

A: Given; Determine the percentage of rods whose lengths lie between 438 mm and 441 mm.Where, The…

Q: Answer the following elating to the drawing in figure (38): 1- What is the name of the component? 2-…

A: A rotational or sliding motion for two parts or maybe more or support an applied load is a shaft…

Q: Using the Milling machine with DRO create a hallow that suites the shape of the given MILD STEEL

A: given; Using the Milling machine with DRO create a hallow that suites the shape of the given MILD…

Q: Sketch shaper machine and explane its parts?

A: Parts of a shaper function are, Base: The Base is fixed to the shop floor and built to take the…

Q: What is the average force magnitude?

A:

Q: the bolt is

A:

Q: What is the axis of symmetry?

A: The Axis of symmetry is the axis that divides an object into two equal halves. symmetry divides the…

Q: What is a bending moment?

A: Bending moment: Bending moment is a moment which developed in any structure or body when a force or…

Q: What is the Orientation of the Neutral Axis?

A: To calculate the neutral axis of a beam or any structure first calculate the centre of inertia of…

Q: What is the thickness of steel?

A: To find thickness of steel.

Q: What is the sliding block?

A: To Define: Sliding block

Q: Which one of the folowing is not correct ?

A: Given; The maximum shear stress theory predicts that shear yieldvalue ζy is 0.5 times the tensile…

Q: It is a tool made from hexagon or octagon-shaped tool steel, one end is shaped for the cutting…

A: Screw driver is the tool which has a holding part made of non conductor and another end is shaped…

Q: In which lathe operation enlarging the already drilled hole can be produced. Boring operation…

A: Correct Option: Boring Operation.

Q: Angle of bite in radian ?

A: Given data; Single pass rolling process;  Diameter, d=420 mm  Width, b=145 mm  Thickness,t=9 mm…

Q: In step 4, it should be the A and not the y right? So it should be FBD divided by 4.04 which is the…

A:

Q: what would you do if it was a through hole that went all the way through the 6 inch shaft?

A: Given question:   what would you do if it was a through hole that went all the way through the 6…

Q: What would a .010 - .020 cutback of a 14.500 Diameter be?

A: Given, Diameter, d= 14.500 mm  Range of cutback: c~ 0.010 - 0.020

Q: What is a Couple Moment?

A:

Q: Which of the following statement is correct in terms of degree of freedom? Select one: Moving…

A: For a 6 DOF system the types of translation and rotation motions are: Moving up and down…

Q: In uptight drill machine, the power is transmitted from electric motor to spindle with help of belt…

A: Drilling machine is a mechanical equipment used to introduce holes into a specimen which are in…

Q: how long does the particle take to go through one revolution?

A: To find Time taken By the  Particle for one revolution

Q: what is the xbar distance (from left edge of part)?

A:

Q: SHAPER MACHINES Shaper operation Types of shaper Principal parts of a shaper

A: Shaper Machine:- Shaping is a machining operation for generating flat surface by means of single…

Q: 4. What is the length of the longest part?

A: To find Length of longest part.

Q: (a) Design a suitable layout for manufacturing a hexagonal bolt  and state its  advantages

A: Solution:

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.