inorder to accomplish a desired angle, A sin bar is used with

Q: What is the low limit on the smallest outside diameter?

A: Solution:

Q: Expandable pattern is used in ?

A:

Q: What is a piece of 1/2" x 1" x 10' long stock commonly called?

A: Given:-  What is a piece of 1/2" x 1" x 10' long stock commonly called?

Q: Q13) For the following micrometer: a- What is the part diameter?

A: 13

Q: QI Define five of the following with sketch. 1-Taper turning 2- Light alloys 3- AA2024 4- Rolling 5-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: Select the correct combination from the given below statements.

A:

Q: What is the internal axial force?

A: Internal Axial Force is defined as the force acting in the direction parallel to the axis of the…

Q: -rce. What is the best angle?

A: To find angle.

Q: The spanners used in workshop are made using ___________ process. a. Forging b. Extrusion c. Drawing…

A: Solution:

Q: Explain Method of Sections in details

A: The method of the section is used to determine the value of unknown forces in members of the truss.…

Q: What is the discontinuity of loading?

A: The load along the length of the structure, say a beam if is consistent then we can say that the…

Q: Q1:- (a) – Give an explanation for each the following:- 1- The design mistake is very dangerous…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: The major diameter of a thread is defined as what

A: A thread is a bank of the constant section in the form of a helix on the internal or external…

Q: Describe thrust angle.

A: Introduction  The thrust angle is basically used as a major angle for alignment of the rear and…

Q: During drilling operation, work piece must be held in vice. Select one: True False

A: Given Statement : During drilling operation, work piece must be held in vice. Select one: True…

Q: What is the basic unit for length?

A: Solution Length → The measurement of something from end to end is called length

Q: In which of the following layout type, materials are fed into the first machine and finished…

A: givenMaterials are fed into the first machine and finished products come out of the last machine.

Q: 2 in. plywood in. 24 in. 3월 in. 2x4 2 x 4 lž in. 1 in. --- 1/2 1/2 1/2

A:

Q: Draw shear force and bending momenE

A:

Q: 1. Once you have overdesigned your product, you need to do a to match the needs and capabilities of…

A: A customer need is a compelling reason for a consumer to buy a product or service. The need…

Q: B. What is the difference between the critical point and triple point? explain with drawing.

A: GIVEN DATA - TRIPLE POINT AND CRITICAL POINT GIVEN WE HAVE TO EXPLAIN IT WITH DRAWING

Q: How does the thickness of a material impact the location of points on an FLD/FLC?

A: FLD: forming limit diagram are used in sheet metal forming processes to find the major and the minor…

Q: The suitable terms for the blanks in the statement ."To change from psig to psia , you must ass…

A: There are many different units of measuring pressure. We can use Pascal(Pa). atmospheric(atm), bar,…

Q: What is compound indexing?

A: Soln:- Compound indexing :- Compound indexing is the operation of obtaining a desired spindle speed…

Q: 1. What thickness limit classifies metal as being sheet? 2. What is the decimal size of 14 AWG…

A: Disclaimer: Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: A

A: ghghh

Q: Material is forced through a die opening called Drawing Select one: OTrue O False

A: A metals working process in which the material is forced through a die such as metal, glass of the…

Q: 18. Mark the one correct statement. a) Material and cross section create stress, loads resist…

A: given - multiple choice question

Q: Steps how to draw a needle of a cannula using SOLIDWORK

A: Dassault Systèmes' SolidWorks is a solid modelling computer-aided design and computer-aided…

Q: Describe the limiting angle of repose. Provide equations and examples to support your point

A:

Q: Hollow shape parts are made __________ process. a. Cold rolling b. Wire drawing c. Deep drawing d.…

A: Rolling process are use to produce the symmetrical objects. Wire drawing process is used to produce…

Q: Draw and state Vernier Calliper Parts?

A:

Q: What is the sliding block?

A: To Define: Sliding block

Q: Match the following. Shaping operation is an example of Bending is an example of

A: Shaping operation is an example of Answer: Primary shaping operation

Q: (a) Explain TWO reasons why the angle dimensions are necessary in the product design? (b) List THREE…

A:

Q: The positive bending moment causes hogging condition in beams.

A: This statement is (FALSE).

Q: The denomination for a force or shrink fit in the US system is ?

A: Solution:

Q: What about the stretch for OA?

A: There is a mistake in the calculation part for TOA.   Consider the three equations (i), (ii), (iii)…

Q: final thickness that can be produced by this

A: Given data;  Diameter=600 mmCoefficient of friction=0.05 Thickness=2 mmDetermine the minimum…

Q: aeroengine

A: At altitude of 10.06km temperature is 223 K c=kRt=1.4*.287*103*223=299.335 m/s…

Q: Material is forced through a die opening called Drawing Select one: True False

A:

Q: What are two advantages of using a shrink-fit toolholder ?

A:

Q: Identify other product that involves Shaper Machine Procedure.

A: A shaper machine is a reciprocating type of machine tool used to produce flat horizontal and…

Q: SHAPER MACHINES Shaper operation Types of shaper Principal parts of a shaper

A: Shaper Machine:- Shaping is a machining operation for generating flat surface by means of single…

Q: What is the counterclockwise angle?

A: The counterclockwise angle is the angle measured in the opposite direction of the clock.

Q: According to ISO 128, if the wide/thick line weight is 0.50mm, what should be the narrow/thin line…

A: According to the ISO 128 , There are some standards following in Engineering drawings  two line…

Q: 7. What is meant by eccentric loading and eccentricity?

A: What is meant by eccentric loading and eccentricity

Q: The possibility to make the required shape from the material is considered during design…

A:

Q: What two things can happen when a flex item drops below its basis size

A:

Q: Magnetic clamps can be used for marking aluminum sheets. Select one: True False

A: Magnetic clamps: The magnetic clamps are used to hold pieces of metals  in their required position…