What is the current, including direction, in the wire connecting points 1 and 3?Express your answer with the appropriate units. Enter positive value if the current flows from point 1 to point 3 and negativevalue if the current flows from point 3 to point 1.11 30AYou have already submitted this answer. Enter a new answer.No credit lost. Try again.Submit Previous Answers Request AnswerPart GHAC 50 ?What is the current, including direction, in the wire connecting points 2 and 47Express your answer with the appropriate units. Enter positive value if the current flows from point 2 to point 4 and negativevalue if the current flows from point 4 to point 2.120SubmitSymbolsAPrevious Answers Request AnswerX Incorrect; Try Again; 5 attempts remaining Three 102 resistors are in the circuit shown in (Figure 1).The left end of the circuit is at a potential of 10 V, whilethe right end is at 0 V.10 Vwwwwww10 Q2100310024 0 V

The given circuit diagram is shown below,

What is the current, including direction, in the wire connecting points 1 and 3? Express your answer with the appropriate units. Enter positive value if the current flows from point 1 to point 3 and negative value if the current flows from point 3 to point 1. HA Submit C PHAED ? 11-30 A You have already submitted this answer. Enter a new answer. No credit lost. Try again. Previous Answers Request Answer

What is the current, including direction, in the wire connecting points 1 and 3? Express your answer with the appropriate units. Enter positive value if the current flows from point 1 to point 3 and negative value if the current flows from point 3 to point 1. HA Submit C PHAED ? 11-30 A You have already submitted this answer. Enter a new answer. No credit lost. Try again. Previous Answers Request Answer

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter27: Service-entrance Equipment

Section: Chapter Questions

Problem 44R

See similar textbooks

Similar questions

The allowable ampacity of a 4 AWG THHN from Table 310.15(B)(16) is 95 amperes. What is this conductors ampacity if connected to a terminal listed for use with 60C wire? ______
Can you help me ? Three identically shaped segments of different materials have a voltage of 120 mV applied between their ends. As a result of the voltage, segment A has a current of 2500muA , segment B has a current of 105 μA and segment C has a current of 0.000002 A. The materials are conductor, semi- conductor and insulators as Determined?
1.A. You've assembled the following components to join two copper conductors: a mould, powdered copperoxide, powdered aluminum, and an igniter. With these components, which of the following processes willyou use to connect the conductors?A. Exothermic weldingB. Irreversible compression groundingC. Mechanical groundingD. Thermal cycling 1.B. Two electricians are discussing voltage ratings. Electrician A says that a motor that's installed 40 feetfrom a power source will show a lower applied voltage than a motor that's installed 20 feet from the samepower source. Electrician B says that an exact voltage of 240 V must be applied to a motor that's rated at240 V. Who is correct?A. Neither Electrician A nor Electrician B is correct.B. Only Electrician A is correct.C. Only Electrician B is correct.D. Both Electrician A and Electrician B are correct.
Which of these are TRUE: 1. Only electron flow is acceptable in interpreting current flow 2. Cross-sectional area is very vital in determining the current density of a conductor 3. The number of electrons that passed a certain area in the conductor can be determined once the amount of electric current is identified 4. The orientation or the direction is a factor in adding or subtracting current 5. The method of calculating for the total resistance for the parallel and series circuits are the same 6. Drift means gradual movement or carried slowly
Determine each system if Static or Dynamic (5 points), Linear or Non-Linear (5 points), Time Variant or Time Invariant (5 points), Causal or Non Causal (5 points). Show proof for each answer. 3. Y3(n)=|x(n)| Please answer this immediately. Thank you!
Which of these are TRUE: 1. Only electron flow is acceptable in interpreting current flow 2. Cross-sectional area is very vital in determining the current density of a conductor 3. The number of electrons that passed a certain area in the conductor can be determined once the amount of electric current is identified 4. The orientation or the direction is a factor in adding or subtracting current 5. The method of calculating for the total resistance for the parallel and series circuits are the same 6. Drift means gradual movement or carried slowly 7. In gold, glass, rubber, and silver. Silver has the least resistivity 8. Current has the capacity to travel in both path at the same time
without pipes, draw a simple diagram of a circuit containing an exhaust fan with on lamp both load controlled by 1 gang 1 way switch.
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: AC CIRCUITS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you! 2. GIVEN.(include symbols and units) 3. REQUIRED/FIND/MISSING (with symbol/s) 4. ILLUSTRATION (Required). 5. STEP-by-STEP SOLUTION with Formulas and Symbols. No Shortcut, No skipping, and detailed as possible 6. FINAL ANSWERS must be rounded up to three decimal places • A positive-sequence three-phase balanced wye voltage source has a phase voltage of Van=100 <20° V. Determine the line voltages of the source.
Question 777 electric Full explain this question and text typing work only All part work u We should answer our question within 2 hours takes more time then we will reduce Rating Dont ignore this line
BASIC ELECTRICAL ENGINEERING UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LONG EXPLANATION NEEDED. ANSWER IN 4 DECIMAL PLACES. BOX THE FINAL ANSWER. Substation 2A have a busbar made of aluminum with a length of 5 meters and a cross sectional areais 4x3 sq. cm. The resistivity of the Aluminum at 20 DegC is 2.82x10-8 ohm-m. Determine theresistance of the busbar
Give me right solution with clear calculations
Consider the circuit shown in (Figure 1). Suppose that R= 150 Ohm. Please answer in typing format solution please only typing format solution