BASIC ELECTRICAL ENGINEERING UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LONG EXPLANATION NEEDED. ANSWER IN 4 DECIMAL PLACES. BOX THE FINAL ANSWER. Substation 2A have a busbar made of aluminum with a length of 5 meters and a cross sectional area is 4x3 sq. cm. The resistivity of the Aluminum at 20 DegC is 2.82x10-8 ohm-m. Determine the resistance of the busbar

BASIC ELECTRICAL ENGINEERING UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LONG EXPLANATION NEEDED. ANSWER IN 4 DECIMAL PLACES. BOX THE FINAL ANSWER. Substation 2A have a busbar made of aluminum with a length of 5 meters and a cross sectional area is 4x3 sq. cm. The resistivity of the Aluminum at 20 DegC is 2.82x10-8 ohm-m. Determine the resistance of the busbar

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter8: Combination Circuits

Section: Chapter Questions

Problem 4PA: The hot water for the heating system for a small factory is supplied by a single boiler. The bolier...

See similar textbooks

Similar questions

Electric heating cable embedded in plaster, or sandwiched between layers of dry wall, creates heat. Therefore, any nonmetallic-sheathed cable run above these ceilings and buried in insulation must have its current-carrying capacity derated according to the (40C) (50C) (60C) correction factors found in Table 310.15(B)(2)(a) in the NEC. (Circle the correct answer.)
After the determination of the currents references, can we connect the ammeter terminals in any way in order to measure the current of a component? *please write it using keybord NOT handwriting*
1.A. You've assembled the following components to join two copper conductors: a mould, powdered copperoxide, powdered aluminum, and an igniter. With these components, which of the following processes willyou use to connect the conductors?A. Exothermic weldingB. Irreversible compression groundingC. Mechanical groundingD. Thermal cycling 1.B. Two electricians are discussing voltage ratings. Electrician A says that a motor that's installed 40 feetfrom a power source will show a lower applied voltage than a motor that's installed 20 feet from the samepower source. Electrician B says that an exact voltage of 240 V must be applied to a motor that's rated at240 V. Who is correct?A. Neither Electrician A nor Electrician B is correct.B. Only Electrician A is correct.C. Only Electrician B is correct.D. Both Electrician A and Electrician B are correct.
Assume that you were tasked to install a microwave oven using 12 AWG copper. When you look at the spec plate for the oven, you discover that the oven is rated for 240V, 60HZ, and takes a current of 25A. The location for the oven is 785.7 Ft, away from the breaker panel. Calculate the expected VD if any. Assume temperature to be 75 ̊ C what is the answer? VD?
What is the ampacity of a #3 AWG Aluminum THWN if there are 3 of them that are considered current carrying conductors in a conduit and the ambient temperature is 86 Degrees F? a 115 b 85 c 100 d 75
Can you help me ? Three identically shaped segments of different materials have a voltage of 120 mV applied between their ends. As a result of the voltage, segment A has a current of 2500muA , segment B has a current of 105 μA and segment C has a current of 0.000002 A. The materials are conductor, semi- conductor and insulators as Determined?
Voltage Drop! Assume that you were tasked to install a microwave oven using 12 AWG copper. When you look at the spec plate for the oven, you discover that the oven is rated for 240V, 60HZ, and takes a current of 25A. The location for the oven is 785.7 Ft, away from the breaker panel. Calculate the expected VD if any. Assume temperature to be 75 ̊ C. what is the Voltage Drop ? Answer?
Please answer the "required" portion. Show full solutions with brief explanation. Required: - total resistance in the picture - type of circuit (either parallel-series or series-parallel) between terminals - AC - BC
In an outdoor substation the three bus-bar conductors are supported by units of post type insulators. Each unit consists of a stack of 3 pin type insulators fixed one on the top of the other. The voltage across the lowest insulator is 15kV and that across the next unit is 12kV. Estimate: i. ratio of mutual to self-capacitance ii. the bus-bar voltage of the substation. iii. Efficiency across the string of insulators
Please I want answer of this Electrical Principles question. Thanks
We are running 3 wires and a ground in a RMC to a control panel with a 60 amp circuit breaker disconnect in the control panel. The conduit is run along the ceiling where the ambient air temperature is 100 degrees. The control panel feeds our secondary cooling pump. What size are the ungrounded conductors? All conductors have typeTHHN insulation. A #6 AWG B 600 Kcmil C #8 AWG D #2 AWG What size RMC do we need? A 3" B 3/4" C 1" D 1 1/2"
ENGINEERING UTILITIES (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LONG EXPLANATION NEEDED. ANSWER IN 3 DECIMAL PLACES. BOX THE FINAL ANSWER.)